Atop EH2316 Series Manual

Unmanaged Ethernet Switch
EH2316 Series
Version 1.0
Updated in November, 2018
P/N : 89900520G
Inside the package you will find the following items:
■ Unmanaged Ethernet Switch x 1
■ 5-Pin 5.08mm Lockable Terminal Block x 1
■ DIN-Rail Kit (Already mounted to the device) x 1
■ Wall Mount Kit Optional to purchase (include M3L5 screws*2)
■ Installation Guide with Warranty Card x 1
Front View
TOP View
Never install or work on electrical or cabling during periods of lightning activity.
Never connect or disconnect power when hazardous gases are present.
Warning:Hot Surface Do Not Touch. RESTRICTED ACCESS AREA: The equipment
should only be installed in a Restricted Access Area.
IndoorIndoor
This equipment should be installed indoor and not connect directly with equipment
installed outdoor.
EH2316-2G
1. 10/100/1000 BASE-T(X) RJ45 Ports
2. 10/100 BASE-T(X) RJ45 Ports
3. PWR1 LED
4. PWR2 LED
5. Grounding Screw
6. Functional Ground
7~8. Terminal for Power 1
9~10. Terminal for Power 2
P1
1
1G
2
3
4
9
10
11
12
5
6
7
8
13
14
15
16
P2
3
1
2
2
2
2
4
F.G.
V1-
V1+
V2-
V2+
5
6
78
10
9
You can then choose whether to plug in the other peripheral ports at this point
or do it later depending on the actual location of the device or level of comfort
for performing such operation.
3.
Once the plate has been firmly put in place, proceed to mount the whole
device as shown in (Fig. 3).Proceed to (Fig. 4) if you want to remove the
device from DIN-Rail.
4.
Next we can then proceed to connect
the device to the LAN (switch or PC,
depending on the case), take care on
using the RJ-45 connector; after this
we can then proceed to the device’s
settings
5.
If you have purchased the wall mount
kit, proceed to place the screws on the
back of the device as show in (Fig. 1).
1.
2. Although internal grounding has been
done inside, in order to ensure overall
maximum performance and protect
your device, it is still strongly advised
to ground the device properly; hazard-
ous ESD can come into contact and
damage your equipment. On the power
terminal block, there is a terminal for
Frame Ground, you can choose
whether to connect it to the grounding
or you may opt to connect to the
grounding screw next to the terminal
block ( the one chosen should be
connected at all times ) (Fig. 2)
■ The opening to the sides are for the
device’s heat dissipation please never
obstruct or cover them with any
objects or try to insert them through it.
F.G.
V1-
V1+
V2-
V2+
(Fig.2)
(Fig.1)
F.G.
V1-
V1+
V2-
V2+
1
2
(Fig.3)
1
2
(Fig.4)

Color State LED Description
Green
PWR1
PWR2
LAN
Amber
Amber
Off
On
On
On
Blinking
Off
On
Blinking
Ethernet is linked
Ethernet is active and data is being transmitted
Ethernet is not linked
Ethernet is linked at 10Mbps
Ethernet is linked at 100Mbps
Ethernet is linked at 1000Mbps
Power is supplied through PWR1
Power is supplied through PWR2
This product is intended to be supplied by an UL62368-1, IEC62368-1 or
IEC60950-1 certify Power Unit marked “LPS” and rated output rating: 12-48 Vdc,
0.6 A minimum, 60°C
Power input : 12-48 VDC, 0.6 A Max
If the device requires servicing of any kind, you may need to disconnect and
remove it from its mounting. The initial installation should be done in a way that
makes this as convenient as possible.
■ Voltage/Power lines should be properly insulated as well as other cables. Be
careful when handing the so as to not trip over
■ Do not under any circumstance insert foreign objects of any kind into the heat
dissipation holes located in the different faces of the device. This may not only
harm the internal layout but might cause harm to you as well.
■ Do not under any circumstance open the device for any reason. Please
contact your dealer for any repair needed or follow the instructions on section
of your User’s Manual.
Field Maintenance and Service
Front View
30
161,8 177,8
46
55
47,5
145
113 12,5
141,8
5555
145
177,8
Customers shall always obtain an authorized "RMA" number from Atop before
shipping the goods to be repaired to Atop. When in normal use, a sold product
shall be replaced with a new one within 3 months after purchase. The shipping
cost from the customer to Atop will be reimbursed by Atop.
After 3 months and still within the warranty period, it is up to Atop whether to
replace the unit with a new one; normally, as long as a product is under warranty,
all parts and labor are free of charge to the customers.
After the warranty period, the customer shall cover the cost for parts and
labor.Three months after purchase, the shipping cost from the customer to Atop
will not be reimbursed, but the shipping cost from Atop to the customer will be
paid by Atop.
Atop shall not be held responsible for any consequential losses from using Atop’s
product.
Warranty Policy
The warranty certification will not be effective until an authorized stamp issued by
Atop’s overseas agents.
Purchase Date: / / (yyyy/mm/dd)
Serial Number
Product CategoriesWarranty WarrantyProduct Categories
Media Converters
Embedded Device Servers
Ethernet Switches
Wireless
Serial Device Servers
Modbus Gateways
DIN-Rail Power Supplies
Power Adaptors
Antennas
Other Accessories
Warranty Conditions
RMA and Shipping Costs Reimbursement
Limited Liability
1. Please contact your local dealers or Atop Technical Support Center at the
following numbers.
+ 886-3-550-8137 (Atop Taiwan)
+ 86-21-6495-6232 (Atop China)
2. Please report the defected problems via Atop’s Web site or E-mail account
Web Site：www.atop.com.tw, e-mail：[email protected]
Web Site：www.atop.com.cn, e-mail：[email protected]
Atop Customer Services and Supports
Products supplied by Atop Technologies are covered in this warranty for
sub-standard performance or defective workmanship. The warranty is not,
however, extended to goods damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake
(c) Use of unqualified power supply, connectors, or unauthorized parts/kits
(d) Replacement with unauthorized parts
Warranty Period
─ Any changes to this material will be announced on Atop website. ─