AUTLED LC-002-010 User manual

LED RF Controller Mono - User Manual
Artikel Nr.: LC-002-010
1. Product Description
The LED RF Controller Mono is for on/off and dimming of Mono-LED‘s. Connection with various
remote controls are possible and it can multiple recipients simultaneously controlled with the
remote control. In addition, the controller can be controlled by standard switch push button.
3. Description
2. Specification
1. Compatible with various remote controls for mono applications
2. Push / Dim function possible with a simple connection of a standard pushbutton
3. Each Receiver can be controlled by max. 8 different remotes
input power 12-24VDC
max. output power 4x5A (240W/12V) oder (480W/24V)
PWM frequency 1500Hz
max. wire cross-section 1,5 mm2
dimensions (L x W x H) in mm 178 x 46 x 19 mm
weight 100g

4. Dimensions
5. Connection and Button Introduction
Connection for
single color LED
Learning Key Button
Power Input
12/24VDC
Connection
Push/Switch
Do wiring according to connection diagram:
1. Short press on the learning key on receiver is when you pair with a remote and short press of
On/Off of the connecting remote. The LED light connected on the receiver flashes and confirmedf
the learning/pairing.
2. If a Push/Switch Button connected, (this works immediately as directly connected to the recei-
ver) short press is to switch the LED light ON/OFF, long press for diming up, long press again for
dimming down.
3. Long press on the learning key on the receiver over 5 seconds until LED light flashes, the
learned ID will be deleted and the receiver will be reset to the factory defaults

L
N
230V~
POWER
PE
POWER
OUT
LED Netzteil | LED Power Supply
12 oder 24VDC
je nach LED | according to LED
POWER
IN
230V
+
–
PE
L
N
LED RF Controller Mono
5 Zonen
Fernbedienung | Remote
LC-002-011
LED Flexstrip MONO | max. 5m
+
–
LED Flexstrip MONO | max. 5m
+
–
LED Flexstrip MONO | max. 5m
+
–
LED Flexstrip MONO | max. 5m
+
–
o
GND
TASTER
BUTTON
Dimmung mittels Taster
optional möglich
Dimming through button
as an option
LED Flexstrip MONO | max. 5m
+
–
LED RF Controller Mono
10 Zonen
Fernbedienung | Remote
LC-002-021
LED RF Controller Mono
Single
Fernbedienung | Remote
LC-002-022
OUTPUT
LED
LED RF Controller Mono -
Empfänger | Receiver
Output: max. 4x5A
LC-002-010
CH1–
+
CH3–
+
+
–+
CH2–
PUSH
DIM
GND
o
+
CH4–
LED RF Controller Mono
4 Kanal
Fernbedienung | Remote
LC-002-014
LED RF Controller Mono
Wandsender Schw. | Weiss
Wall Remote Black | White
LC-002-012 | LC-002-013
LED RF Controller Mono
Doppeltastermodul
Double Push Button Module
LC-002-015
LED RF Controller Mono
1 Zonen Funktaster
1 Zone Radio Push Button
LC-002-016
LED RF Controller Mono
2 Zonen Funktaster
2 Zone Radio Push Botton
LC-002-017
6. Connection Diagram
7. Safety warnings
1. To avoid installed the product in minefield, strong magnetic field and high voltage area.
2. To ensure the wiring is correct and firm avoiding short circuit damages to components and
cause fire.
3. Please install the product in a well ventilated area to ensure appropriate temperature
environment.
4. The product must be worked with DC constant voltage power supply.
Please check the consistence of input power with the product, if the output voltage of the
power comply with that of the product.
5. Connect the wire with the power on is forbidden. Ensure proper wiring first then check to
ensure no short-circuit, then power on.
6. Don‘t repair it by yourself whenever an error occur. Contact the supplier for any inquiry.