AUTLED LC-004-944 User manual

LED DALI Controller Touch RGBW DT8 - 4 Zones
User Manual
Item no.: LC-004-944
1. Product Description
The DALI controller is a touch panel and sends DALI signals to DALI actors. This controller is
suitable for RGB and RGBW LED lights. It has a high sensitive glass touch panel with which you
can adjust any desired colour. The touch panel can control 4 DALI groups and 4 DALI scenes.
The DALI Device Type (DT) 8 device can be supplied passive via DALI bus or activ supplied
with 230VAC. Mounting on a commercially available 68mm flush-mounted box.
2. Specifiations
Power Supply 100-240VAC oder DALI Bus
Operation current 230VAC: <15mA | DALI consumption: 4mA
DALI Bus Output max. 100mA
Output Signal DALI
Max. wire-cross section 1,5mm²
dimensions 86 x 86 x 41,6 mm
3. Operation Manual
ON/OFF button or dimming
short press: turn on / off the controller. When switched on a blue LED lights up above the
colour wheel. long press: up,- or down dimming of the desired colour.
scene button
With this button you can call up the self-saved scenes. press the previously stored DALI group
1, 2, 3 or 4. Then briefly press the S button. Then select the saved scene with the buttons 1, 2,
3 or 4.
Colour wheel
At the colour wheel you can choose the desired colour or the colour mix.

4. Einstellungen
Play/Pause button
First short keystroke: Starting the 10 permanently stored color gradients.
Repeated short press: Pause the color gradient.
Long press of the button: The color speed is increased or slowed down.
Zone selection or sabind of 4 different scenes
These buttons can be used to select zones, long press turn the zone on / off or scenes to be
called and saved
R G B W - buttons
If you press shortly, you can switch between the individual channels.
First long press - brightness is increased, second long press - brightness is dimmed down.
Briefly press the button - channel is switched on, - or switched off.
1. Assignment of the DALI - Group:
The rear rotary switch determines which DALI group and scenes are controlled or stored
by the touch panel. A total of 15 groups + 1x broadcast can be selected.
If you set the rotary switch to position „0“ at Group, the command „broadcast“ will be sent.
For positions „1“ to „F“, groups 0-14 are addressed directly. The 16th DALI Group
which is designated 15, can not be addressed directly.
Note: For a group-wise control, it is necessary to assign the DALI actors to one or more
DALI groups. The DALI Touch Panel can not perform a group assignment.
Please note the detailed group setting:
Rotary Switch
Position 0 1 2 3 4 5 6 7 8 9 A B C D E F
DALI Group
for button 1 Broadcast 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
DALI Group
for button 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 BC
DALI Group
for button 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 BC 0
DALI Group
for button 4 2 3 4 5 6 7 8 9 10 11 12 13 14 BC 0 1

2. Setting the scene number:
The touch panel allows scene selection of upto 4 scenes.
A rotary switch on the back serves to select the scenes you want to control and to set
the starting scenes. Here you can choose between 16 scenes (0-15).
If you set the rotary switch to position „0“ in Scene, the 4 possible scenes become (S1-S4)
stored in the DALI actors under scene 0 to scene 3.
If you set the rotary switch, e.g. at position „7“, scenes 7-10 are occupied and at position „F“
scenes 15, 0, 1 and 2 are occupied.
Please note the detailed setting table for scenes as follows:
Rotary Switch
Position 0123456789ABCDEF
Scene assigned
to S1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Scene assigned
to S2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0
Scene assigned
to S3 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1
Scene assigned
to S4 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 2
4. Dimensions and Wiring
DALI signal 230VAC
Rotary switch
for scenes
Rotary switch
for groups

5. Installation
6. Wiring Diagram
Passiv: Supply via external DALI bus power supply

Active: Connection via 230VAC
Active: If supply is with 230VAC, the touch panel provides a
bus supply (100mA) to control 50 DALI actors. In broadcast
mode, a maximum of 2 active panels and 2 passive panels
for controlling 100 DALI actors can be connected to a DALI
line.