AUTLED LC-004-942 User manual

LED DALI Controller Touch DW DT8 - 4 Zones (Groups)
User Manual
Item no.: LC-004-942
1. Product Description
The DALI controller is a touch panel and sends DALI signals to DALI actors.
This controller is suitable for tunable white (dynamic white) LED lights. It has a high
sensitive glass touch panel with which cold and warm white can be mixed and dimmed.
The touch panel can control 4 DALI groups and 4 DALI scenes. The DALI Device Type (DT) 8
device can be supplied passive via DALI bus or activ supplied with 230VAC.
Mounting on a commercially available 68mm flush-mounted box.
2. Specifications
Power Supply 100-240VAC oder DALI Bus
Operation current 230VAC: <15mA | DALI consumption: 4mA
DALI Bus Output max. 100mA
Output Signal DALI
Max. wire-cross section 1,5mm²
dimensions 86 x 86 x 41,6 mm
3. Operation Manual
ON/OFF button
When switched on, a blue LED lights up above the color wheel.
Brightness
Press and hold down to increase / decrease the light intensity.
Colour wheel
At the color wheel you can choose the desired color or the color mix of cold and warm white
to adjust. When adjusting the light color, the brightness always remains constant. When set to
cool white, it will light up to 100%. When warm white is set this lights up to 100%. When neutral
white is set, cool white becomes 50% and warm white 50%.
The colors are reduced by percentage depending on the direction of the slider, but the overall
color remains 100%. e.g. Cold white 70% and warmwhite 30%.

4. Operation
Zone buttons
With the 4 Zone buttons you can choose the desired DALI group. With long press button
you can switch on/off the desired Zone.
scene buttons
These keys can be used to recall and store moods. To save a scene, proceed as follows:
Press a scene button for 3 seconds until the connected LED lights up, the set scene has now
been saved. To call up a saved scene, briefly press the appropriate scene button.
1. Assignment of the DALI - Group:
The rear rotary switch determines which DALI group and scenes are controlled or stored
by the touch panel. A total of 15 groups + 1x broadcast can be selected.
If you set the rotary switch to position „0“ at Group, the commands Broadcast will be sent.
For positions „1“ to „F“, groups 0-14 are addressed directly. The 16th DALI Group
which is designated 15, can not be addressed directly.
Note: For a group-wise control, it is necessary to assign the DALI actors to one or more
DALI groups. The DALI Touch Panel can not perform a group assignment.
Please note the detailed group setting:
Rotary Switch
Position 0 1 2 3 4 5 6 7 8 9 A B C D E F
DALI Group
for button 1 Broadcast 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
DALI Group
for button 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 BC
DALI Group
for button 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 BC 0
DALI Group
for button 4 2 3 4 5 6 7 8 9 10 11 12 13 14 BC 0 1

2. Setting the scene number:
The touch panel allows scene selection of upto 4 scenes.
A rotary switch on the back serves to select the scenes you want to control and to set
the starting scenes. Here you can choose between 16 scenes (0-15).
If you set the rotary switch to position „0“ in Scene, the 4 possible scenes become (S1-S4)
stored in the DALI actors under scene 0 to scene 3.
If you set the rotary switch, e.g. at position „7“, scenes 7-10 are occupied and at position „F“
scenes 15, 0, 1 and 2 are occupied.
Please note the detailed setting table for scenes as follows:
Rotary Switch
Position 0123456789ABCDEF
Scene assigned
to S1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Scene assigned
to S2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0
Scene assigned
to S3 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1
Scene assigned
to S4 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 2
4. Dimensions and Wiring
DALI signal 230VAC
rotary switch
for scenes
rotary switch
for groups

5. Installation
6. Wiring diagram
Passiv: Supply via external DALI bus power suuply

Active: Connection via 230VAC
Active: If supply is with 230VAC, the touch panel provides a
bus supply (100mA) to control 50 DALI actors. In broadcast
mode, a maximum of 2 active panels and 2 passive panels
for controlling 100 DALI actors can be connected to a DALI
line.