Automatic Technology ATS Series User manual

Sectional Door Opener
Instruction Manual
Doc # 160091_02
Part # 86296
Released 03/06/19
ATS Series
TEMPO ATS-2
SECTIONAL DOOR OPENER

ATS Series Instruction Manual2
Table of Contents
1. Installation Safety Warnings! 3
2. Before you Begin 4
3. Tools Required 4
4. Kit Contents 5
5. Position 5
6. Fit the Opener 6
7. Bracket Position 6
Wall Bracket Position: 6
Mounting The Wall Bracket: 6
Attach The Rail To The Wall Bracket 6
8. Perforated Angle 7
9. Mounting Brackets and Arms 7
Mounting The Door Bracket: 7
Attaching the Arms 7
10. Optional Safety Beam Kit 8
11. Setting Limits 9
Set the Limit Positions and adjust drive speed: 9
Clearing the Door Limit Positions 9
Re-profiling the Door 9
12. Safety Testing 10
Test the Close Cycle 10
Testing the Open Cycle 10
Test the Manual Door Operation 10
13. Auto-Close 10
14. Coding a Transmitter 11
Storing the Transmitter Code 11
Installation of the Wall Mounted Transmitter 11
Remotely Coding Transmitters 11
Erasing All Transmitter Codes 11
Vacation Mode 11
15. Home Owner Safety Warnings! 12
16. Opener Safety & Security 13
Your Door CAN NOT be used when: 13
Your Door CAN be used when: 13
To Disengage the Opener: 13
To Re-Engage the Opener: 13
17. Operating your Opener 13
18. User Operating Controls 14
19. Specifications 15
20. Troubleshooting 16
21. Maintenance 18
22. Battery Replacement 19
23. Battery Disposal 19
24. Appendix 20
A - Status Indication during Operating Mode. 20
B - Adjustment Mode Instructions 21
C - Adjusting Force Margins 21
D - Battery Functions 21
E - Setting limits via Transmitter 22
F - Setting the PET Mode position 22
25. Warranty 23
Installation Instructions Home Owner Instructions

3ATS Series Instruction Manual
1. Installation Safety Warnings!
WARNING! • The door may operate unexpectedly, therefore do not allow anything to stay in the path of
the door.
• When operating the manual release while the door is open, the door may fall rapidly due
to weak or broken springs, or due to being improperly balanced.
• The drive must not be used with a door incorporating a wicket door, unless the drive cannot
be operated with the wicket door open.
• The drive is intended to be installed at least 2.5m above the floor.
• Do not disengage the opener to manual operation with children/persons or any objects
including motor vehicles within the doorway.
• If the door is closing and is unable to re-open when obstructed, discontinue use. Do not
use a door with faulty obstruction sensing
• When using auto close mode, a Photo Electric beam must be fitted correctly and tested
for operation at regular intervals. Extreme caution is recommended when using auto close
mode. All safety rules must be followed.
ELECTROCUTION! • Place opener in protected area so that it does not get wet.
• Do not spray with water .
• Disconnect the power cord from mains power before making any repairs or removing covers.
Only experienced service personnel should remove covers from the opener.
• If the power supply cord is damaged, it must be replaced by an Automatic Technology
service agent or suitably qualified person.
• Connect the opener to a properly earthed general purpose 240V mains power outlet
installed by a qualified electrical contractor.
CAUTION:
Emergency Access • If garage has no pedestrian entrance door, an emergency access device should be
installed. This accessory allows manual operation of the garage door from outside in case
of power failure.
Muscular strain • Practice correct lifting techniques (carton weighs approx 9kgs)
• Practice correct lifting techniques when required to lift the door as per installation instructions.
Fall from ladder • Ensure ladder is the correct type for job.
• Ensure ladder is on flat firm ground that will take the weight without the legs sinking.
• Ensure user has 3 points of contact while on ladder.
Crush injury from unsecured
door
• Place a 2 metre exclusion zone around area under the door while it is unsecured.
• Follow the installation instructions
Garage Door • Examine the door installation, in particular, springs and mountings for signs of wear, damage
and imbalance.
• The garage door must be well balanced. Sticking or binding doors must be repaired by a
qualified garage door installer prior to installation of the opener.
• Remove or disengage all garage door locks and mechanisms prior to installation of the opener.
Entanglement • Never plug in and operate opener prior to installation.
• Keep hands and loose clothing clear of door and guides at all times.
Entrapment under
operating door
• DO NOT operate the opener unless the garage door is in full view and free from objects
such as cars and children/people. Make sure that the door has finished moving before
entering or leaving the garage
• In order for the opener to sense an object obstructing the door way, some force must be
exerted on the object. As a result the object, door and/or person may suffer minor damage
or injury.
• Ensure the garage door is in good working order by undertaking regular servicing.
• Install the optional wall transmitter in a location where the garage door is visible, but out
of the reach of children at a height of at least 1.5m.
• Photo Electric beams must be installed if the closing force at the bottom edge of the door
exceeds 400N (40kg)
This automatic garage door opener is designed and tested to offer safe service provided it is
installed and operated in strict accordance with the following safety warnings. Failure to comply
with the following instructions may result in death, serious personal injury or property damage.

ATS Series Instruction Manual4
3. Tools Required
2. Before you Begin
Test the following before commencing installation:
a. The door MUST BE in good operating condition.
b. Manually move the door up and down, the door should move freely without
binding or sticking.
c. The maximum force required to move the door should not exceed 20kg.
d. Lift the door to about halfway. When released, the door should stay in place.
DIY
DO NOT DO IT YOURSELF:
If any of the above door requirements are not met, DO
NOT attempt to fix yourself. Please contact a garage door
professional. (P) 13 62 63
Examine the conditions in the garage:
a. Look at the ceiling:
i. Is it plastered? The opener is mounted to a perforated angle which MUST be securely fastened to a structural support.
You will need to locate the structural beams in the ceiling which are generally 400mm apart.
ii. Does it have exposed beams? The opener is mounted to a perforated angle which must be securely fastened to a
structural support like the exposed beams. You may need to install a 40mm thick board (not supplied) between structural
supports.
b. Look at the wall above the garage door.
i. Is it brick? The wall bracket MUST be securely fastened to the wall with suitable screws and ensure it does not move.
Screwdrivers
Adjustable End Wrench
Sockets and Wrench
Pencil
Drill
2 x Screws
(M6 x 20mm)
Stepladder
Perforated Angle
Metal pieces
(32 x 32 x 1.5mm) x 1200mm length
4 x Screws
(M8 x 20mm)
4 x Bolts and Nuts
(M8)
Drill Bits
Pliers
Hack saw
Tape Measure
Level
ii. Is it timber? The wall bracket MUST be securely fastened to a structural
support. You may need to install a 40mm thick board (not supplied) between
structural supports to fasten the wall bracket to.

5ATS Series Instruction Manual
4. Kit Contents
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
15
1. 1 x ATS drive unit
2. 1 x Wall mount transmitter
3. 2 x Transmitters and batteries
4. 1 x Bent arm door attachment
5. 1 x Straight arm door attachment
6. 1 x Wall bracket TS01
7. 1 x Door bracket Locator
8. 1 x Door bracket
9. 3 x Pin Snap SSP 8 ZNU 31080
10. 2 x Hex Head screw M8x25
11. 1 x Pin 0890
12. 2 x Clevis Pin 0829
13. 2 x Hex Serration flange nut M8
14. 4 x Hex flange screw taptite ‘S’ M4 x 10
PLUS
15. 2 x Track Bracket
16. 1 x Pre-Assembled Rail
10.00°
min
MINIMUM HEAD
ROOM FOR STEEL
RAIL 57mm
DOORS HIGHEST
POINT
15
1
16
5
4
6
7
12
8
14
11 9
13
10
5. Position
Perforated
Angle
The Opener:
a. MUST BE installed in a dry position, protected from weather.
b. REQUIRES properly earthed 3 pin single phase power on the ceiling within an arms length of the opener.
c. Requires a MINIMUM HEADROOM of 57mm between the highest point of the door’s travel and the ceiling.
d. Use the diagram below as a reference when completing the installation.
129
9

ATS Series Instruction Manual6
6. Fit the Opener
Secure C-Rail to Opener:
a. Remove the Opener from the box.
b. Locate and insert the shaft of drive unit 1into the C-Rail’s sprocket.
c. Fix the two track brackets 15 with four (4) M4 x 8 screws 14 supplied in accessory pack.
d. Place drive unit back in packing box for protection.
Locate shaft into
the sprocket
16
1
15
14 WARNING! DO NOT
use tek screws to affix
rail. Only use the screws
provided, and fix these
into the threaded holes
in the chassis.
7. Bracket Position
Wall Bracket Position:
a. Determine the centre of the door and mark this point with a line on the wall
above.
b. Raise the door and find the highest point of travel of the first (top) door panel.
60mm
Level
WARNING! The Opener must be securely fastened to structural
supports, otherwise opener failure may ensue causing serious
personal injury and / or property damage.
DO NOT DO IT YOURSELF: If sufficient structural support can not
be found, contact a door professional for installation.
DIY
c. Using step ladder and a level, transfer this height to the wall above the door
and mark a line 60mm above it, across the centre line.
Mounting The Wall Bracket:
a. Draw two lines extending 21.5mm from each side of the centre point.
b. Centre the wall bracket 6over the intersection of these two lines. Mark
centres for at least two holes and ensure it is into a solid mounting point.
c. Drill holes in the wall with an appropriate bit.
d. Secure to the wall using:
i. IF CONCRETE OR BRICK:
8mm (5/6”) loxins/dynabolts.
ii. IF TIMBER:
wood screw #20 or similar (min. 50mm).
Attach The Rail To The Wall Bracket
a. Leave the drive unit in its packing box on the floor for protection and lift the
other end of the C-Rail.
b. Attach the C-Rail assembly 16 to the wall bracket 6with the
90mm long pin 11 and secure with the supplied pin snap 9.
16
11
9
6
6

7ATS Series Instruction Manual
8. Perforated Angle
Attach Perforated Angle (not supplied) or equivalent
a. Measure across the ceiling from the centre point 3155mm (+/- 50mm) to find a supporting beam.
b. Create a perforated angle which best suits your site. Use a hack saw to cut the L shape metal strips. Secure the perforated
angle to a supporting beam using diagrams shown below.
c. Raise the drive unit to the ceiling mounted perforated angle and secure with M8x20mm screws and nuts (not supplied). Strips
should not extend more than 18mm below centre of drive unit mounting holes.
d. To prevent moisture on the C-rail running into the powerhead it is recommended a strip of silicon sealant is placed across the
top of the C-rail just before the opener.
Ceiling Beams that run towards the door requires:
1 x perforated L shape metal strip and
2 x shorter perforate L shape metal drop down strips.
Ceiling Beams that run parallel to the door requires:
2 x perforated L shape metal strips and
2 x shorter perforate L shape metal drop down strips.
(Not supplied)
9. Mounting Brackets and Arms
Mounting The Door Bracket:
a. The door bracket locator 7is placed over the door bracket
8, on the door’s centre line one-third down the top panel and
mounted using M6 or equivalent screws (not supplied),
b. STEEL DOORS ONLY: Bracket can be welded in place.
NOTE: If in doubt about the door’s strength, reinforcement
may be added to the door’s frame where necessary. Door
damage may occur if the bracket is installed on a panel
with insufficient strength. The opener’s warranty does not
cover damage caused to the door and/or door panels.
Attaching the Arms
a. Assemble the bent arm 4(connecting to the door) to the
right side of the straight arm 5with bolts 10 and nuts 13
supplied in the accessory pack. Connect the straight arm 5to
8
7
7
12
9
4
13
6
10
9
12
8
5
the shuttle with a clevis pin 12 and a pin snap 9. Always use both bent and straight arms.
b. Connect the assembled arm to the bracket with clevis pin 12 and pin snap 9. The angle “A” must be more than 10°.
A

ATS Series Instruction Manual8
10. Optional Safety Beam Kit
Safety Beams
The Safety Beam Kit provides additional safety by preventing the door closing when
the beam is blocked by a car, child etc. When the Safety Beam Kit is installed the
Auto-close feature can be enabled if required.
a. To install the Safety Beam Kit, refer to the Safety Beam instruction supplied with
the kit.
b. After the beams are installed the beam alignment feature of the opener can be
used.
c. Turn power on to the opener.
d. Align the safety beams using the main light as a guide:
i. bright = aligned
ii. dull = not aligned or blocked
When the beam is aligned or if no beam is fitted, continue with Setting Limits.

9ATS Series Instruction Manual
Set the Limit Positions and adjust drive speed:
The Limit Positions can vary due to site conditions, such as uneven
ground. When setting the Close limit, ensure the position is when the
door makes first contact with the ground. Alternatively for the Open
limit the position should be at the height of the garage opening.
NOTE: The drive speed is set to the fastest setting by default. This
may not be suitable for larger doors or for single piece doors.
a. Switch power on and the BLUE LED on the CLOSE button
will start to flash and the GEAR LED is lit to indicate that the
opener is ready to set the Close travel limit.
b. Press either the CLOSE or OPEN button to move the door
to the halfway point.
WARNING! In setting the close limit position,
do not force the door into the floor with
excessive force, as this can interfere with
the ease of operation of the manual release
mechanism.
Door Opener
Speed Mode
STATUS MAIN LIGHT
Fast (Default) On 3 Flash
Medium On 2 Flashes
Slow On 1 Flashes
WARNING! The door will automatically close,
open and close again after the next step.
Ensure that nothing is in the door’s path.
11. Setting Limits
NOTE: If unhappy with the speed or travel limit setting,
restart this procedure by resetting the door limit positions
as per below first.
Clearing the Door Limit Positions
Limit positions can be deleted by:
a. Press the MODE button repetitively until the GEAR
LED is lit.
b. Press and hold the MODE button for 10 secs, let the
MODE button go when the main light stops flashing.
c. The close LED will flash continuously to indicate limits
have been cleared.
NOTE: If no action is taken within 30 seconds, the opener
will return to normal operating mode and restore the original
settings.
d. Follow from CLOSE limit: above to set new limit positions.
CLOSE limit:
i. Press and hold the CLOSE button to start closing
the door, taking note of the speed the door moves.
ii. If the close speed is not suitable, to make a change,
press and hold the CLOSE button and by pressing the
STOP / SET button on the opener it will cycle through
all three speed modes as shown in table.
iii.Once at the desired speed, release the CLOSE button.
iv. To set the close limit, inch the door by making single
presses of the CLOSE button to the desired
position. We recommend the CLOSE limit position
being the first point of contact of the rubber strip ( at
the bottom of the door) with the ground.
v. If the door overshoots, press the OPEN button to
move the door in the OPEN direction.
vi.When the door is at the desired CLOSE position, press
the STOP / SET button on the opener, the GREEN
LED on the OPEN button will now flash.
OPEN limit:
i. Press and hold the OPEN button to start opening
the door, taking note of the speed the door moves.
ii. If the open speed is not suitable, to make a change,
press and hold the OPEN button and by pressing the
STOP / SET button on the opener it will cycle through
all three speed modes as shown in table.
iii.Once at the desired speed, release the OPEN button.
iv. Continue inching the door to the desired position.
v. To set the open limit, inch the door by making single
presses of the OPEN button to the desired
position. We recommend the OPEN limit position
being the height of the garage opening.
vi.If the door overshoots, press the CLOSE button
to move the door in the CLOSE direction.
vii. When the door is at the desired OPEN position,
press the STOP / SET button The door will now
automatically close and open to calculate the safety
obstruction settings.
Re-profiling the Door
Re-profiling is a simplified way of re-learning the travel
characteristic of a previously setup Limit Switch travel
installation. Re-profiling can be used when the travel
characteristics of the door change due to mechanical
adjustments etc. To initiate a re-profile:
a. Limits must be set.
b. Press the MODE button repetitively until the GEAR
LED is lit.
c. Press and hold the CLOSE button for two
seconds, the door will open and close by itself to
record profile.

ATS Series Instruction Manual10
12. Safety Testing
Test the Close Cycle
a. Press the OPEN button or transmitter button to open the door
(If the door starts closing, press the transmitter button to stop the
door, then press transmitter again to open).
b. Place a piece of timber 40mm high on the floor directly under the
door.
c. Press the transmitter button to close door.
d. The door should strike the object and re-open.
e. Remove the timber.
Testing the Open Cycle
a. Press the CLOSE button or transmitter button to close the
door.
b. Press the transmitter button again to open the door.
c. When the door reaches approximately half way, firmly grab the
door’s bottom rail - the door should stop.
If the door does not reverse readily when closing, or stop when
opening, put the door into manual by pulling down on the manual
release string to disengage the motor and contact 13 62 63 for
support.
Test the Manual Door Operation
Periodically disengage the opener and manually operate the door.
The door must be smooth to operate by hand. The force required on
the bottom rail should not exceed 20kg.
CAUTION: Take care when completing a
safety test. Failure to follow this warning
can result in serious personal injury and/or
property damage.
WARNING! If the door is closing and is unable
to re-open when obstructed, discontinue use.
Do not use a door with faulty obstruction sensing.
Wood 40mm high
WARNING! If the door fails these tests,
put the opener into manual mode, only
operate the door by hand and call for
service.
13. Auto-Close
WARNING! It is compulsory to have
Safety Beams installed when using
Auto-Close mode.
Auto-Close mode is a function that automatically closes the door after
a pre-set time. Safety beams must be installed in order to run the Auto-
Close function. There are two types of Auto-Close available:
i. Standard auto-close - the door will Auto-Close after a
programmed time. In this mode the timer starts to countdown
as soon as the door is fully open. This function is useful in case
the safety beam does not get triggered.
ii. Safety Beam triggered auto-close - the door will auto-close
after a programmed time. In this mode the timer starts counting
down only when the safety beam is triggered. ie car leaving the
garage.
To enable the Auto-Close function:
a. Press the MODE button until the GEAR LED starts flashing.
b. Press the OPEN button until the GEAR LED flashes:
i. two (2) times to get to PE auto-close or
ii. three (3) times to get to standard auto-close.
c. Press STOP / SET button to enter parameter.
d. The default setting for Auto-Close is OFF. Press the
OPEN button to move through options and the
light’s brightness will change accordingly.
e. Press STOP / SET button to save the parameter’s new
value or press MODE to leave the value unchanged.
Parameter Value options = Indicated by brightness of
main light (DEFAULT parameter underlined)
Name Flashes 123456
PE AUTO-CLOSE 2OFF 15sec 30sec 60sec 90sec -
AUTO-CLOSE 3OFF 15sec 30sec 60sec 90sec 120sec
WARNING! Safety beams must be
installed if the closing force at the bottom
edge of the door exceeds 400N (40kg).

11ATS Series Instruction Manual
14. Coding a Transmitter
Storing the Transmitter Code
The opener can only operated from remote control
transmitters that have been programmed into its
memory. Up to 64 codes can be stored in the memory.
a. Press the MODE button until the TRANSMIT
LED is lit.
b. Press and HOLD the button/s indicated in the table
to set the required transmitter function. The Main
light will start to flash rapidly.
c. Press one of the four (4) buttons on the transmitter
until the main light starts to flash rapidly, then release
transmitter button.
d. Press the remote control button again until the main
light stops flashing rapidly.
e. Release both buttons. The transmitter button is now
coded, press to test.
NOTE: Refer to the Light indicator table for the details
of the transmitter status.
BUTTON
TRANSMITTER
FUNCTION
Open / Stop / Close HOLD
PET (Pedestrian) Mode HOLD
Open HOLD
Light HOLD HOLD
Vacation Mode HOLD HOLD
MAIN LIGHT TRANSMITTER
STATUS
ON Button added
OFF Button removed
2 FLASHES, then OFF Remote control deleted
4 FLASHES, then OFF Memory full
Installation of the Wall Mounted Transmitter
a. Store the transmitter code as per instructions
above. Test the transmitter button.
b. Mount the transmitter in a convenient location, yet
out of reach of children and at least 1.5m off the
ground.
c. Make sure the door is visible from this location.
Remotely Coding Transmitters
Using this method transmitters can be coded without access to
the opener’s control panel as long as a pre-coded transmitter is
available.
a. Take any pre-coded transmitter. Press the button for the
function to be duplicated and release.
b. Using a small needle / pen, press and hold firmly for two
seconds the middle button, through the Coding Hole.
c. Within ten (10) seconds take the additional transmitter you
wish to code. Hold the new transmitter’s button for two
seconds, pause for two seconds, hold again for two seconds
and then release.
d. Wait for ten (10) seconds and then press the new transmitter’s
button to test.
Erasing All Transmitter Codes
a. Press the MODE button until the TRANSMIT LED is lit.
b. Press and hold the MODE button for 10 secs, let the MODE
button go when the main light stops flashing.
c. Follow steps a - e in Storing the Transmitter Code to code
new transmitters.
Vacation Mode
a. To turn on Vacation mode and lock out all remotes, press the
button on the remote programmed with Vacation Mode.
b. To turn off Vacation Mode, press the transmitter button
programmed to vacation mode to turn off.

ATS Series Instruction Manual12
Please read these important safety warnings!
This automatic garage door opener is designed and tested to offer safe service provided it is
installed and operated in strict accordance with the following safety warnings. Failure to comply
with the following instructions may result in death, serious personal injury or property damage.
WARNING! • When operating the manual release while the door is open, the door may fall rapidly due to
weak or broken springs, or due to being improperly balanced.
• DO NOT disengage the opener to manual operation with children/persons or any objects
including motor vehicles within the doorway.
• If the door is closing and does not re-open when obstructed, discontinue use. DO NOT use a
door with faulty obstruction sensing.
ELECTROCUTION! • Place opener in protected area so that it does not get wet.
• DO NOT spray with water .
• DO NOT open the protective covers.
• DO NOT operate opener if cable is damaged.
DO NOT DO IT
YOURSELF
• Keep the garage door balanced. Sticking or binding doors must be repaired. Garage doors,
door springs, brackets and their hardware are under extreme tension and can cause serious
personal injury. DO NOT attempt any garage door adjustment. DO NOT use if repair or
adjustment is needed. Call for a professional garage door service.
CAUTION:
Emergency access • If your garage has no pedestrian entrance door, an emergency access device should be
installed. This accessory allows manual operation of the garage door from outside in case of
power failure.
Entrapment under
operating door
• Watch the moving door and keep people away until the door is completely opened or closed.
DO NOT operate door when persons are near the door.
• DO NOT allow children to play with door controls or transmitters.
• Regularly conduct Open and Close cycle testing.
• Ensure the garage door is in good working order by undertaking regular servicing.
• Wall transmitters should be installed in a location where the garage door is visible, but out of
the reach of children at a height of at least 1.5m.
• Install Safety Beams (recommended).
Fall from Ladder • Ensure ladder is the correct type for the job.
• Ensure ladder is on flat ground.
• Ensure user has 3 points of contact while on ladder.
Entanglement in or
laceration from
moving door
• Keep hands and loose clothing clear of door and guides at all times.
• Keep hands clear of moving door as sharp edges can cause cuts or lacerations.
DIY
15. Home Owner Safety Warnings!

13ATS Series Instruction Manual
15. Home Owner Safety Warnings! 16. Opener Safety & Security
Your Door CAN NOT be used by the opener when:
a. There is a locking device installed.
b. There is a power failure.
Your Door CAN be used when:
a. There is an emergency, by disengaging the opener.
b. There is a power failure, by disengaging the opener.
To Disengage the Opener:
a. It is recommended to do so with the door in the closed position.
b. Pull the manual release cord towards the door, until you hear a click.
c. Move the door manually.
To Re-Engage the Opener:
a. Check the door has not been locked by a locking device.
b. Pull the manual release cord away from the door, until you hear a click.
c. The door will now operate from the opener.
CAUTION: When the opener is manually disengaged,
the door is no longer locked. To lock the door
manually, re-engage the opener after the door is
closed.
17. Operating your Opener
To Operate the opener:
a. Press the programmed transmitter button until your
door begins to move (usually 2 seconds). Make sure
you can see the door when you use the transmitter.
b. If you are in a vehicle you should aim the transmitter
through your windscreen as shown.
c. Check that the door is fully open or closed before you
drive in or away.
d. If you press the transmitter whilst the door is moving
the door will stop. The next press of the transmitter
will move the door in the opposite direction.
WARNING! When operating the manual
release (while the door is open) the door
may fall rapidly due to weak or broken
springs, or due to being improperly
balanced.
Do not disengage the opener to manual
operation with children/persons or any
objects including motor vehicles within
the doorway.
CAUTION: Do not use the string handle as a
mechanism to open the door. Failure to comply may
cause serious injury.

ATS Series Instruction Manual14
18. User Operating Controls
05 06 07
01
02
03 04
Button Function
1. DOWN ARROW (Blue) Closes the door
2. DOWN ARROW LED (Blue) Illuminates when the door is closed and flashes when the door is obstructed on close
or stopped.
3. STOP (Red) Stops the door
4. UP ARROW (Green) Opens the door
5. UP ARROW LED (Green) Illuminates when the door is open and flashes when the door is open with the auto-
close timer running, obstructed on opening or stopped.
6. MODE (Yellow) Enables Load Diagnostics Mode
7. MODE STATUS LED (Yellow) Illuminates when in Diagnostics Mode
8. BATTERY STATUS LED (Yellow) Illuminates when battery is charged and flashes when battery is charging, in use or
battery failed. Battery function not available with ATS-2 model.
9. REMOTE CONTROL
STATUS LED (Red)
Flashes on remote lockout and flickers on remote control activity
10. ADJUSTMENT LED (Yellow) Flashes a certain number of times depending on the parameter being changed.
11. NETWORK LED
(Not Available with ATS-2)
08091011

15ATS Series Instruction Manual
19. Specifications
Technical Specifications ATS-2
Rated voltage range: 230V - 240Va.c.
Rated frequency: 50Hz / 60Hz
Rated power input: 165W
Door opening:
Maximum Door Area:
Maximum Door Weight:
Door must be well balanced and able to be operated by hand, as per
warranty conditions and AS/NZS 4505:2012
18m2
200kg*
Minimum headroom 57mm
Rated Operating Time 4 mins
Rated Temp +5oC to +40oC
Short Term Peak force: 1100N
Rated load 400N
Nominal force 200N (20kg)
Receiver type Multi-frequency UHF FM
(433.47, 433.92 & 434.37MHz)
Receiver code storage capacity 64 X 4-button Transmitters
Transmitter battery CR2032 (3 Volts)
Main light LED (Light Emitting Diodes)
Network connectivity Network compatible,
(requires optional Smart Phone Control Kit)
* Gross door weight, including all fittings
Note: Intermittent operations may occur in areas which experience very strong winds. The strong wind puts extra pressure on the
door and tracks which may in turn intermittently trigger the safety obstruction detection system.

ATS Series Instruction Manual16
20. Troubleshooting
Symptom Possible cause Remedy
The opener does not
work from the transmitter
Garage door in poor condition e.g.
springs may be broken
The opener does not have power
The battery in the transmitter is flat
The opener has turned on “Vacation
Mode”
The transmitter button is not
programmed to operate the door.
Check the door’s operation
Plug a device of similar voltage (e.g. a hair dryer)
into the power point and check that it is OK
Replace the battery
Turn off “Vacation Mode”
(Section 14)
Code in the transmitter
One transmitter works
but the other/s do not
Faulty transmitter
Flat battery
Replace transmitter
Replace battery
The chain / belt moves
but the door remains
stationary
The opener is disengaged Re-engage the opener
The transmitter range
varies or is restricted
Variations are normal depending on
conditions e.g. temperature or external
interference
The battery life is exhausted
Position of the transmitter in the motor
vehicle
Make sure you can see the door when you use the
transmitter.
Check the battery status by pressing a button
(flashing or no light requires battery to be changed)
Aim the transmitter through the windscreen.
The Courtesy light does
not work
LED has failed Change LED.
The door reverses for no
apparent reason
This may occur occasionally from
environmental conditions such as areas
that are windy, dusty or have extreme
temperature changes.
If Safety beams are installed they may
be partially obstructed.
Ensure the door runs smoothly before increasing the
force pressure.
Ensure the beam path is not obstructed. Check the
Alignment.
Auto Close not working Safety Beam or wiring faulty Repair Safety Beam or replace wiring.
Re-align optics. See Safety Beam instructions.
The door stops or moves
very slowly under battery
(Optional Battery Back
Up Accessory)
The batteries may have little OR no
charge
Connect mains power and leave the batteries to
charge. The batteries may take 24 to 48 hours to
reach their maximum charge capacity.
The Main light is
repeatedly flashing OFF a
number of times followed
by a pause
Generally the opener can still be used. The issue type is indicated by the number of
flashes shown.
The CLOSE (Blue) LED is
flashing
Limits are not set Set Up Limits (Section 11).

17ATS Series Instruction Manual
20. Troubleshooting
If You Need a Service Call
If the opener needs a service please call the dealer who installed the garage door opener (their contact details are usually
on a sticker on the back of your garage door). For product assistance contact 13 62 63 within Australia.
BEFORE CALLING you should have the following information to assist in providing the appropriate service:
1. Has anything happened since the opener last operated OK, e.g. a storm, a jolt to the door etc.?
2. What is the current light status on the opener?
3. Manually disengage the door (Section 16).
How easy is it to manually open and close the door?
4. What model is the opener? (Model no. information is located at the rear of the opener)
5. Who installed the opener? (Dealer details should be on a sticker on the back of your garage door)
6. When was it installed? (If known)
Flashes Issue Remedy
1Normal operation (door is fully open)
2PE is preventing door from moving Clear away any obstructions. Test Door. If unable to move the
door and suspect beam is faulty, enter Safety Beam Emergency
Close by pressing and holding a pre-coded button on transmitter
for more than five seconds and the door will start closing.
3NOT AVAILABLE
4 Wireless PE battery is low Change PE Battery
5NOT AVAILABLE
6 Maintenance is due after pre-set number of cycles. Contact dealer to arrange service.
7Standby battery is faulty Contact 1300 769 850 within Australia for assistance
8 Door was obstructed Clear away any obstructions and test door opens/closes
correctly. (If door is damaged, contact your door professional)
9 Motor overloaded or stalled Check the doors operation by disengaging the motor and
ensuring the door runs smoothly. If necessary make door
adjustments or contact your door professional.
10 Unit running on battery power Main light will flash (3) three times at the start of the cycle to
indicate opener is running from battery backup.
Check power supply.
Main Light = Service / Warning Indicator:
Requirements for a service and user warnings are indicated after operation by the main light repeatable flashing OFF a
number of times followed by a pause. The below table identifys the issues and remedies.

ATS Series Instruction Manual18
21. Maintenance
Door Maintenance
A poorly maintained door could cause fatal / serious injuries or damage
to property.
•Frequently examine the door, particularly the cables, springs and
mountings for signs of wear, damage or imbalance. DO NOT USE if
repair or adjustment is needed since a fault in the installation or an
incorrectly balanced door may cause injury.
•Fasteners: Check all screws, nuts and bolts to ensure they are secure.
•Spring Tension: It is natural for springs to lose tension. Should the
door become hard to operate or completely inoperative, contact a
door professional.
•Guide Tracks: Clean the internal sections of the guide tracks every
3 - 6 months with a cloth dampened with mineral turps or methylated
spirits.
DO NOT DO IT YOURSELF:
WARNING! Failure to maintain your
garage door may void the warranty on
your garage door opener.
DIY
Door adjustments should only be
carried out by experienced persons,
as this function can be dangerous if
not performed under strict safety
procedures.
Run the Safety Testing procedures
MONTHLY in Section 12 to ensure
garage door is fit for use.
tip

19ATS Series Instruction Manual
When batteries reach the end of their usual life in accordance with Australian Battery Recycling Initiative please follow the next
simple steps for protecting the environment. Refer to the Automatic Technology website for information on where to recycle
batteries in Australia.
DO NOT throw the batteries in municipal waste. This symbol of the crossed out wheeled bin
indicates that the battery should not be placed in the municipal waste. Check your local regulations
for appropriate disposal of the batteries.
Recycling all batteries will have other environmental and social benefits:
WARNING! Prior to disposal, recycling, or collection, all battery terminals must be securely
insulated with a non conductive material to prevent any two batteries from short circuiting
and generating heat during storage or transport. Battery terminals may be insulated with
electrical tape; or batteries may be individually packaged in a non conductive material
(e.g., plastic bag or original packaging).
23. Battery Disposal
Battery Type:
3V Lithium Battery CR2032.
• To test the battery is working, press and
hold a transmitter button. Check Light
Status table to determine if battery needs
replacing
Light Status Battery Status
Solid OK
Flashing Requires replacement
No light Requires replacement
22. Battery Replacement
Use a pen
to push the
battery down
through the
side opening
to release
battery
• Use finger nails to separate
the transmitter casing to
expose circuit board.
• Use a non-metallic object
(e.g. pen) to remove the
battery.
•Some batteries are less toxic but hazardous for other
reasons. Lithium batteries can explode or catch fire in
landfill, while button cells are dangerous if swallowed
by children. Recycling offers a safe and environmentally
responsible solution for end of life batteries.
•Battery recycling recovers non-renewable materials such
as lead, cadmium, stella, zinc, manganese, cobalt, silver,
plastics and rare earth elements.
•Removal of batteries and other hazardous household
products from household waste facilitates the recovery of
organic materials through alternative waste technologies
such as composting. Batteries and heavy metals are known
contaminants in compost.
•The community supports recycling because it reduces
waste to landfill and achieves environmental benefits.

ATS Series Instruction Manual20
24. Appendix
A - Status Indication during Operating Mode.
LEDs Light Status Description
BLUE GREEN YELLOW RED PURPLE
DOOR OPEN 2AND
CLOSED 1LEDS
solid
flashing
flashing
solid
solid
flashing
flashing
flashing
solid
Open
Open with Autoclose timer running
Opening / Obstructed on Open
Closed
Closing / Obstructed on Close
Stopped
Partial Open
MODE LED 3flashing Load Diagnostics mode
BATTERY LED 4off
solid
flashing
rapid
flashing
Battery not used / not fitted
Battery charged
Battery charging, when connected
to power, without power battery
in use (holding STOP for 10s will
shutdown)
Battery failed
REMOTE CONTROL
STATUS LED 5
flashing
rapid
flashing
Remote lockout
Remote Control Activity
NETWORK LED 6
(not available on ATS-2
model)
05
06
01
02
03
04