Automatic Technology Axess Pro Series 1101 Quick start guide

Featuring TrioCode™Technology
Doc # 160034_01
Part # 13384
Released 05/03/14
Axess®Pro Series 1101
Commercial Overhead Garage Door Opener

2Axess Pro Series 1101 Owner Installation Instructions
Automatic Technology (Australia) Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an
Automatic Technology (Australia) Pty Ltd industrial roller shutter opener. Automatic Technology (Australia) Pty Ltd hereby
further expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any
person as a result whether directly or indirectly from failure to install the Automatic Technology (Australia) industrial roller
shutter opener in accordance with these installation instructions.
WARNING: Electrical wiring must be in compliance with
your local building and electrical codes.
WARNING: It is vital for the safety of persons to follow
all instructions. Failure to comply with the installation
instructions and the safety warnings may result in serious
personal injury and/or property and remote control opener
damage. Please save these instructions for future reference.
NOTE: For full automatic operation a Safety Beam (Photo
Electric Beam Sensor) must be fitted to the logic console
with this opener. Failure to comply will void the warranty and
may cause serious personal injury and/or property damage.

Owner Installation Instructions Axess Pro Series 1101 3
Axess®Pro Series 1101
Commercial Overhead Garage Door Opener
Contents
1. Important Safety Instructions 4
2. Controller Input And Outputs 6
3. Set up Requirements 7
3.1 Kit Contents 7
4. Pre-Installation Requirements 8
4.1 Initial Check 8
4.2 Drive Unit Pre-assembly 8
5. Installation 9
6. Safety Beam Installation 10
6.1 Fitting the Safety Beam 10
6.2 Wiring the Safety Beam 10
6.3 Alignment 10
7. Powering up the Axess®1101 11
8. Setting Limits 12
8.1 Setting Travel Limits 12
8.2 Setting close travel limit 12
8.3 Setting open travel limit 12
8.4 Automatic limit adjustment and load profile 12
8.5 Pedestrian access position 12
8.6 Errors during setting of travel limit 12
9. Safety Obstruction Force Test 13
9.1 Testing Close Cycle 13
9.2 Testing Open Cycle 13
9.3 Recalculate Force Margins 13
10. Coding Transmitter 14
10.1 Coding Transmitter Button 14
10.2 Selecting Function Of The Button 14
10.3 Returning To Main Screen 14
11. Remotely Coding Transmitters 15
11.1 Selecting The Function To Be Coded 15
11.2 Activate Remote Code Set Mode 15
11.3 Removing the Battery From the Transmitter 15
12. Setting Pedestrian Position 16
12.1 Setting Pedestrian Position 16
12.2 Checking Pedestrian Position 16
12.3 Error Displays 16
13. Auto-Close Mode 17
13.1 Setting Up Standard Auto-Close 17
13.2 Safety Beam Triggered Auto Close 17
13.3 Pedestrian Auto-Close 17
13.4 Auto-Close After Obstruction: 17
14. Accessories Installation 18
14.1 Fitting Solenoid Or Magnetic Locks 18
14.2 Fitting Courtesy Lights 18
15. Specifications 19
16. Troubleshooting 20
17. Maintenance 21
17.1 Door Maintenance 21
17.2 Lubrication (every 3 - 6 months) 21
17.3 Door Service and Repair 21
17.4 Opener Maintenance 21
18. Appendix 22
A - Console Menu Structure 22
B - Viewing & Editing Parameters 25
C - Control Board Adjustments 26
D - Diagnostic Tools 28
E - Memory Tools 29
F - Transmitter Editing 30
G - Transmitter Management 31
Warranty and Exclusion of Liability 32

4Axess Pro Series 1101 Owner Installation Instructions
WARNING! • The door may operate unexpectedly, therefore do not allow
anything to stay in the path of the door.
• For Safety protection, a Safety Beam must be fitted with logic
console. Failure to comply will void the warranty and may result in
serious personal injury and/or property damage .
• The drive must not be used with a shutter incorporating a wicket door,
unless the drive cannot be operated with the wicket door open.
• The drive is intended to be installed at least 2.5m above the floor.
• DO NOT allow children to operate the opener. Any device that can
operate the opener, make sure it is out of reach of children and that
the doorway is in full view at all times. Serious personal injury and/or
property damage can result from failure to follow this warning.
• If the door is closing and is unable to re-open when obstructed,
discontinue use. Do not use a door with faulty obstruction sensing
• When using auto close mode, a Safety (Photo Electric) Beam must
be fitted correctly and tested for operation at regular intervals.
Extreme caution is recommended when using auto close mode.
All safety rules must be followed.
ELECTROCUTION! • Place opener in protected area so that it does not get wet.
• Do not spray with water .
• Disconnect the power cord from mains power before making any
repairs or removing covers. Only experienced service personnel
should remove covers from the opener.
• If the power supply cord is damaged, it must be replaced by an
Automatic Technology service agent or suitably qualified person.
• Electrical wiring must be compliance with the local building an
electrical codes.
The safety alert symbols below indicate a personal
safety or property damage instruction exists.
READ THESE INSTRUCTIONS CAREFULLY.
This automatic shutter opener is designed and tested to
offer safe service provided it is installed and operated in
strict accordance with the following safety rules. Failure
to comply with the following instructions may result in
death, serious personal injury or property damage.
1. Important Safety Instructions

Owner Installation Instructions Axess Pro Series 1101 5
1. Important Safety Instructions
CAUTION:
Emergency access • If your facility has no pedestrian entrance door, an emergency access device
should be installed.
Entrapment under
operating door • DO NOT operate the opener unless the door is in full view and free from objects
such as cars and children/people. Make sure that the shutter has finished moving
before entering or leaving the premises.
• Do not allow children to play with door controls or transmitters.
• In order for the opener to sense an object obstructing the door way, some force
must be exerted on the object. As a result the object, door and/or person may
suffer damage or injury.
• Ensure the door is in good working order by undertaking regular servicing.
• For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a
Safety (Photo Electric) Beam.
• Safety beams must be installed if the closing force at the bottom edge of the door
exceeds 400N (40kg)
Installation • Frequently examine the installation, in particular cables, springs and mountings
for signs of wear, damage or imbalance. DO NOT use if repair or adjustment
is needed since a fault in the installation or an incorrectly balanced door may
cause injury. DO NOT attempt to repair the shutter yourself as hardware is under
extreme tension.
•The door must be well balanced and in good working order. door springs, brackets
and their hardware are under extreme tension and can cause serious personal injury.
Do not attempt to adjust them. A faulty door must be repaired by a industrial roller
door professional prior to opener installation.
• Remove or disengage all door locks and mechanisms prior to installation of the
opener.
• Ensure no parts of the door or installation extend over public paths or roads.
• After installation a full function test of the system and safety devices must be
done.
Security • Make sure the door is fully closed before leaving the driveway.
Entanglement in
moving door • Keep hands and loose clothing clear of door and opener at all times.

6Axess Pro Series 1101 Owner Installation Instructions
2. Controller Input And Outputs
+ − 1 2 3 4 5 V+ LGT LCK V+ IN V−
24VDC
DRIVE UNIT P.E BEAM
COM
OPN
STP
CLS
OSC
SWP
PED
RELAY OUTPUTS
13
04
02
01
05
14
15
16
15
16
08
Fig 2.1
03
12
11
10
09
07
06
24VDC+ output for powering accessories 3A(max)
24VDC- output for powering accessories 3A(max)
Drive unit connections
Com Terminal for light or lock interface relay drive
Light interface relay drive
Lock interface relay drive
V+ PE Beam power
PE Input Terminal
V- PE Beam Power
COM terminal for inputs terminals 11-16
OPN N/O input terminal
STP N/O input terminal
CLS N/O input terminal
OSC N/O input terminal
SWP N/O input terminal
PED N/O input terminal
Console Exit Button
Console Previous Button
Console Down/Close Button
Console Up/Open Button
Console SET Button
Console Next Button
Antenna Connector
Console Display
Motor Speed Control Connector
Programmer Interface Connector
3 Ampere 240 Volt Fuse
Motor Control Connector
24V AC Power Supply Input Terminal
01
02
03
04
05
06
07
08
09
10
11
12
13
14
28
29
17
18
19
20
21
22
23
24
25
26
27
2829
17
18
19
20
21
22
23
24
25
26
27

Owner Installation Instructions Axess Pro Series 1101 7
3. Kit Contents
Fig 3.1
1
2
3
17
16
15
19
10
11
12
18
4
ITEM DESCRIPTION QTY ORDER
CODE
1 POWER HEAD WV 3P 1101 1 92531
2 PTX-5V2 TC-128 TRANSMITTERS 2 61167
3 SAFETY BEAMS KIT PACK 1 61751
4 STRAIGHT ARM 1 62790
5 BENT ARM 1 62800
ACCESSORY PACK IPDO-2 (92520)
6 NILOCK NUT M8 1 10860
7 FLAT WASHER 1 11020
8 SLEEVE 081246 1 64385
9 HEX HEAD SCREW M8 X 70 1 10088
10 WALL BRACKET 1 62525
11 DOOR BRACKET LOCATOR 1 62515
12 DOOR BRACKET 1 62511
13 PIN SNAP SSP 8 ZNU 31080 3 10720
14 HEX HEAD SCREW M8 X 25 2 10110
15 CLEVIS PIN 0829 2 62551
16 HEX SERRATION FLANGE NUT M8 2 10148
17 HEX HEAD SCREW M8 X 16 4 10120
18 SPRING WASHER 4 10950
AXESS PRO TRACK KIT
19 AXESS PRO TRACK KIT 4M 1 92510
AXESS PRO TRACK KIT 5.85M 1 92511
9
14
13
5
8
7
6

8Axess Pro Series 1101 Owner Installation Instructions
4. Pre-Installation Requirements
The Axess®Pro Series 1101 is designed to operate most
commercial heavy duty and heavy residential overhead doors.
The door must be in good working condition and travel freely
in the guides.
4.1 Initial Check
Before commencing installation, check the following:
a. The door moves freely for the full travel in both directions.
b. The mounting must be a solid construction (concrete, brick
or steel) and must be able to withstand the full driving force
applied to the door.
c. There is a 240V 10 Amp power point located within one metre
of the drive unit.
d. Safety Beam must be installed. The Safety Beams should be
positioned as close to the door as practicable.
4.2 Drive Unit Pre-assembly
The drive unit 1and track assembly 19 are supplied as two
separate parts. The drive sprocket is part of the track assembly.
a. To connect track to the drive unit, remove the front cover.
b. Disconnect the trolley from the chain index (Fig 4.1).
c. Loosen tension on the chain. Do not disconnect the chain.
d. Locate the sprocket keyway with keyway on the Reducer and
slide it in place until the face of sprocket boss sits against the
shoulder on drive shaft of the reducer.
NOTE: The whole track has to slide with the sprocket. It can be
knocked on with a mallet or “helped” with a screwdriver.
e. Once the sprocket is in position, lock cap head screw.
f. Secure the track to drive unit with the four (4) M8 x 16
Hex Head screws 17 .
g. Tighten the chain and lock it with lock nuts.
h. Connect the front cover to the drive unit.
IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION
Warning: Incorrect installation can lead to severe injury.
Follow ALL installation instructions.
Fig 4.1
19
1
17
Drive Sprocket
Trolley Chain Index

Owner Installation Instructions Axess Pro Series 1101 9
5.1 Mounting The Drive Unit
a. Determine the centre of the door and mark this point on the
wall above (Fig. 5.1).
b. Raise the door to the open position.
c. Rest the opener on a support above the top edge of the door
to allow for a 25mm gap between the shuttle and the door
(Fig. 5.2).
d. Mark the position of the wall bracket 10 on the wall above the
door (Fig. 5.3).
e. Secure the wall bracket 10 in place with loxins or appropriate
fasteners (not supplied).
f. Secure the opener to the ceiling above drive unit mounting
holes, with perforated angle or similar (not supplied). Do not
lock the screws at this stage.
g. The door bracket comes in two parts. The door bracket locator
11 is placed over the door bracket 12 and uses 4 mounting
holes for extra strength. Mount the door bracket to the centre
line of the door (Fig. 5.4), using M6 or equivalent screws (not
supplied) Alternatively it can be welded on steel doors.
NOTE: If in doubt about the strength of the door, reinforcement
may need to be added to the frame or panel where necessary.
Damage to the door panel may occur if the bracket is installed
incorrectly on a panel with insufficient strength. The door opener
warranty does not cover damage caused by the opener to the
door and/or door panel.
h. Assemble the bent 5and straight arm 4with two (2) M8 x 25
Hex Head Screw 14 and two (2) M8 Hex Serration Flange Nut
16 (Fig. 5.5).
i. Connect the assembled arm to the door bracket 12 and the
trolley by a clevis pin 15 and a pin snap 13 .
NOTE: The shuttle must be in disengage position. Always use
both the bent & straight arms. If installing on a door with bad
wave action, lengthening the arm even further will assist the door
operation by reducing the wave action.
5. Installation
Fig 5.1
Track
Door
Fig 5.2
Fig 5.3
Fig 5.4
Fig 5.5
Perforated angle
11
12
Trolley
4
12
15
13
14
16
515
10

10 Axess Pro Series 1101 Owner Installation Instructions
6. Safety Beam Installation
6.1 Fitting the Safety Beam
a. Attach the mounting bracket 4to the adjustment bracket
3with the pan head screw 6. (Fig. 6.1)
b. Attach the bracket 2 to the Safety Beam transmitter with
four M3 x 5 taptite screws 5 and attach the other side to
the adjustment bracket 3 with the pan head screw 6 .
(Fig. 6.2)
c. Repeat steps a and b to assemble the Safety Beam
receiver.
Locate the Safety Beam in a strategic location in the doorway.
Automatic Technology recommends that the sensor is placed
100mm above the floor level and as close as possible to the
shutter opening.
6.2 Wiring the Safety Beam
a. Connect a Resistor 5k6 ohms (Green Blue Red Gold)
to number 2 (two) and 4 (four) terminal on the Safety-2
receiver (Fig. 6.3). Make sure to align the beams correctly.
Follow the manual supplied with the Safety Beams.
b. Ensure you program the Axess®Pro Series 1101 to idenitfy
what type of Safety Beam you have installed.
i. Press NEXT to Navigate to Menu 7
ii. Press SET to display Menu 7.1 (for IN3).
iii. Use the UP and DOWN arrows to change the Safety
Beam type from two to three wires.
iv. Press SET to accept the selection.
CAUTION: Before plugging the opener in, check
the power cord for damage and ensure it cannot
become entangled in any moving parts
6.3 Alignment
a. Power up the Axess®Pro Series 1101 with the Safety Beam
connected. The green LED on the transmitter should turn
ON to indicate power is present.
b. If the receiver is connected to power and the red LED is
flashing while the green LED on the transmitter is on, the
transmitter and receiver are not aligned.
c. Make horizontal and/or vertical adjustment on the
transmitter and/or receiver until the red LED on the
receiver turns on, indicating alignment. Approaching
to the alignment is indicated by fast flashes on the red
receiver LED.
Fig 6.1
Fig 6.2
1
2
5
4
36
6
V+
IN
V−
RED
BLUE
GREEN
GOLD
BLACK BLACK BLACK BLACK
YELLOW
RED
YELLOW
RED
++-
-
RED
SAFETY BEAM
Fig 6.3
V+
IN
V−
RED
BLUE
GREEN
GOLD
BLACK BLACK BLACK BLACK
YELLOW
RED
YELLOW
RED
++-
-
RED
SAFETY BEAM