Autonics AFE Series User manual

B-16
AFE Series
Sensor connector type terminal block
lEasy wiring works and significant time saving combined with
sensor connector
[wire mount plug(CNE-P - , sold separately)]
lUnnecessary wire stripping and specific tools
lSpace saving with compact size
lEasy check for operation status and for cable break
by adopting LED signal
l2 ways of mounting (DIN rail, mounting with screws)
lSelectable NPN/PNP input (NPN/PNP selection switch)
Model
Features
Example of sensor connector type terminal block connection
Example of connection AFE4-H20-16LF and 40-point I/O module PLC with branch cable
Branch cable
PLC I/O Unit
AFE4-H20-16LF
AFE4-H20-16LF
24 VDC I/O I/O
GND
00 01 02 03 04 05 06 07
08 09 0A 0B 0C 0D 0E 0F
24 VDC I/O I/O
GND
00 01 02 03 04 05 06 07
08 09 0A 0B 0C 0D 0E 0F
※ For sensor connector wire plug (CNE Series), refer to A-2 to 5 pages.
※ It is recommended for I/O cable to use Autonics CJ Series
(connector transmission cable). Refer to -1 page.
Model Item Connector type
for primary
For secondary Number
of sensor
connectors
LED Case type
Connector type Number of
connector pins
AFE4-H20-16LF Interface
terminal block
Sensor
connector 4-pin
socket
Hirose
connector
20-pin 16EA Yes Full case type
AFE4-H40-32LF 40-pin 32EA
Please read “Caution for your safety” in operation manual
before using this unit.

(A)
Sensor
connector
(B)
I/O terminal
block
(C)
I/O cable
(D)
Remote I/O
terminal block
B-17
Sensor Connector Type Terminal Block
AFS
AFL/AFR
ACS
AFE
ABS
Relay
Model AFE4-H20-16LF AFE4-H40-32LF
Power supply 12-24 VDC
Allowable voltage range 90 to 110% of rated voltage
Rated current Max. 1A ※1
Number of connector pins 20-pin 40-pin
Number of sensor connectors 16EA 32EA
Insulation resistance Min. 1,000 ㏁ (at 500 VDC megger)
Dielectric strength 600 VAC 50/60 Hz for 1 min.
Vibration Mechanical 0.75 mm amplitude at frequency of 10 to 55 Hz(for 1 min.) in each of X, Y, Z directions for 1 hour
Malfunction 0.75 mm amplitude at frequency of 10 to 55 Hz(for 1 min.) in each of X, Y, Z directions for 10 min.
Shock Mechanical 150 m/s2(15G) in each of X, Y, Z directions for 3 times
Malfunction 100 m/s2(10G) in each of X, Y, Z directions for 3 times
Environ-
ment
Ambient temperature -15 to 55 ℃, storage : -25 to 65 ℃
Ambient humidity 35 to 85%RH, storage : 35 to 85%RH
Material CASE, BASE : PC
Tightening torque 0.7 to 0.8 N·m
Approval
Weight※2Approx. 121 g(Approx. 69 g) Approx. 203 g(Approx. 119 g)
Specications
※1: The rated current includes LED current of terminal block.
※2: The weight is with packaging and the weight in parentheses is only unit weight.
※Environment resistance is rated at no freezing or condensation.
Dimensions
●AFE4-H20-16LF
●AFE4-H40-32LF
(unit:mm)
※Factory default of the NPN/PNP selection switch is NPN.
※Indicator(PW: red LED, operation and disconnection: blue LED)
38.2
Ø4
128
70
79
24
VDC
I/O
I/O
GND
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F
NPN/PNP
selection switch
Indicator※
35.2
72
70
38.2
79
Ø4
76
24
VDC
I/O
I/O
GND
00 01 02 03 04 05 06 07
08 09 0A 0B 0C 0D 0E 0F
NPN/PNP
selection switch
Indicator※
35.2
72
70

B-18
AFE Series
Sensor connector socket arrangement
※No. 2 and 4 are connected
1 12-24VDC
2 I/O
3 GND
4 I/O
How to squeeze sensor connector wire plug
●Cover color and wire specications for sensor connector wire mount plug
Model Cover color
Applied wire specications
Norminal cross section
area (mm²) Cover diameter (mm)
CNE-P04-WT Transparent(WT)
0.05 to 0.08
(AWG30 to 28)
ø 0.6 to 0.8
CNE-P04-YG Yellow-Green(YG) ø 0.8 to 1.0
CNE-P04-VT Violet(VT) ø 1.0 to 1.2
CNE-P04-RE Red(RE)
0.13 to 0.21
(AWG26 to 24)
ø 0.8 to 1.0
CNE-P04-YW Yellow(YW) ø 1.0 to 1.2
CNE-P04-OG Orange(OG) ø 1.2 to 1.6
CNE-P04-GN Green(GN)
0.32 to 0.5
(AWG22 to 20)
ø 1.0 to 1.2
CNE-P04-BL Blue(BL) ø 1.2 to 1.6
CNE-P04-GY Gray(GY) ø 1.6 to 2.0
Specications of sensor connector wire mount plug
(unit: mm)
16.5
5.9
※Sensor connector plug is sold separately.
12.5
16
4 3 2 1
1)Insert wires. 2)Squeeze the connector.
lCheck the pin number and insert wires at the insertion part
of the cover.
lCheck the wires are inserted at the end of cover.
lInsert the cover to the body with tools (press fitting plier, etc).
lSqueeze it with tools at the side direction as below
figure.
After
squeezing
Before
squeezing ※Sensor connector wire plug is sold separately.
Refer to A-2 to 5 pages.
-

(A)
Sensor
connector
(B)
I/O terminal
block
(C)
I/O cable
(D)
Remote I/O
terminal block
B-19
Sensor Connector Type Terminal Block
AFS
AFL/AFR
ACS
AFE
ABS
Relay
lRemoving
1)Insert a screwdrive into holes of rail lock and pull the lock out to
the direction "①".
2)Removing the unit by pulling to the direction "②".
Connections
●AFE4-H20-16LF
●AFE4-H40-32LF
2 20
19
1
※Hirose connector model
: HIF3BA-20PA-2.54DSA
※Hirose connector model
: HIF3BA-40PA-2.54DSA
2 40
39
1
Installations
Mounting to and Removing from DIN rail Mounting with screws
< Mounting > < Removing >
①
②
①
②
Rail lock
DIN rail
①
①
Rail lock
2-M4 screw
Caution for using
1. Use the product within the rated specifications for operating temperature and humidity.
2. Check voltage fluctuations in the power supply within the rated range.
3. When connecting PLC or other controllers, check the polarity of power before wiring.
4. Power wire should be AWG16(1.25 mm2).
5. Do not use NPN output sensor and PNP output sensor simultaneously.
6. Do not use this unit at below places.
① Place where there is severe vibration or impact
② Place where strong alkalis or acids are used
③ Place where there are direct ray of the sun
④ Place where strong magnetic field or electric noise are generated
7. In case of 24VDC signal input, isolated and limited voltage/current or Class2 source should be provided for power supply.
8. Installation environment
①It shall be used indoor.
②Altitude max. 2,000 m
③Pollution Degree 2
④Installation Category II
20 18 16 14 12 10 8 6 19 17 15 13 11 9 7 5 4 3 2 1
GND
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
NPN
VCC
PNP
VCC
GND
V
1
G
1
V
2
G
2
V
3
G
3
V
4
G
4
V
5
G
5
V
6
G
6
V
7
G
7
V
8
G
8
V
9
G
9
V
10
G
10
V
11
G
11
V
12
G
12
V
13
G
13
V
14
G
14
V
15
G
15
V
16
G
16
43 2
15678
40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 39 37 35 33 31 29 27 25 23 21 19 17 15 13
11
9
00
V
2
G
2
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1E 1F1D
1C
GND
GND
VCC
VCC
PNP
NPN
N·C
V
3
G
3
V
4
G
4
V
5
G
5
V
6
G
6
V
7
G
7
V
8
G
8
V
9
G
9
V
10
G
10
V
11
G
11
V
12
G
12
V
13
G
13
V
14
G
14
V
15
G
15
V
16
G
16
V
17
G
17
V
18
G
18
V
19
G
19
V
20
G
20
V
21
G
21
V
22
G
22
V
23
G
23
V
24
G
24
V
25
G
25
V
26
G
26
V
27
G
27
V
28
G
28
V
29
G
29
V
30
G
30
V
31
G
31
V
32
G
32
V
1
G
1
●
Mounting
1)Push the rail locks to the direction "①".
2)Hook DIN rail connection onto DIN rail.
3)Push the unit down to the direction "②" and then push up the rail
locks to the unit body.
1)This unit is able to mount on the panel with rail locks.
2)It is recommended to use M4×15 mm of spring washer
screws and to use flat washers which are diameter Ø 6.
The tightening torque should be 0.7 to 1.0 N·m.