HDMI
UHD EXTENDER
HDM-3EXCU 100M + USB
HDM-3MXCU 40M + USB
HDM-3MXC 40M
(Local or Remote)
USER MANUAL V1.0
Package Contents-
2x HDM-3EXCU or HDM-3EXC or HDM-3MXCU or
HDM-3MXC Unit
1x User manual
1x USB Micro B to Type A Cable ( HDM-3EXCU
HDM-3MXCU Only )
1x IR Receiver Cable
1x IR Blaster Cable
2x Terminal Blocks 3P
1x Power adapter DC 12V with lock
Anything missed, please contact with your vendor.
-1-
Features
Through the HDMI Extender, you can use one BD or
UHD Source to display identical image and extension
of HDMI signal up to 100 Meter on UHD TV.
HDCP Compliant
Supports 3D pass-through
Support RS-232(Bi-direction transfer)
Supports all frequency band IR extension control
One CAT.6A U/FTP cable extension *Note
Supports UHDTV up to 4k2k@60 4:4:4 & HDR
HD-BaseT technology
USB 2.0 Extender
Supports Power over Cable ( POC ) *Note
Specifications
Function HDM-3EXCU HDM-3MXCU HDM-3MXC
HDMI A-Type Female x 1
HDMI A-Type Female x 1
Terminal block (TXD GND RXD)
ψ
ψ
USB Micro B
USB 2.0 ( Host
or Device )
USB 2.0 ( Host
or Device )
NA
Setup USB/IR/Gender Function
4k2k 60fps 4:4:4 / 8K 30fps 4:2:0
Cable Distance
DC 12V with lock
107.2 x 69 x 20 mm (LxWxH)
LOCAL FRONT VIEW
1. DIP SW : USB/RS232/Gender Device Setup
2. IR IN
3. IR OUT
4. LED : Power/Mode/LINK/Gender/HDMI TX/HDMI RX
5. RS232 : TX/GND/RX
-2-
LOCAL REAR VIEW
1. Power Jack
2. LINK : HDBT TX/RX
3. HDMI IN
4. HDMI OUT
5. USB : Host/Device ( 3EXCU & 3MXCU Only)
Installation
1. Connect the HDMI extension cable between the BD and
the “HDMI IN” port of HDM-3EXCU Local TX Device.
2. Connect the HDMI extension cable between the UHDTV
and the “HDMI OUT” port of HDM-3EXCU Remote RX
Device.
3. Connect the CAT.6A cables between the TX “LINK” port
and the RX “LINK” port of extender.
4. Connect the power cord on the extender.
5. Turn on the BD UHDTV and Power on HDM-3EXCU.
IR Receiver Cable Directions:
Put it into the Device “IR IN” port and place the IR Receiver
Cable, so that you can point to it easily with your IR remote
extension controller.
IR Blaster Cable Directions:
Plug IR blaster cable plug into Device “IR OUT” port, It sits
in front of the BD receiver’s IR sensor, which is located on
the front-panel.
RS232:
1. Connect RS232 signal to RS232 TXD/GND/RXD Port
on HDM-3EXC TX and RX Device.
2. RS232 baud rate support to 115200.
USB
1. Setup the HDM-3EXCU Dip SW to USB Host or
Device.
2. Connect Cable between the PC and HDM-3EXC USB
Host Port.
3. USB Micro B to Type A Cable Connect to HDM-3EXCU
USB Device Port and Plug in USB Device on Cable
Type A Port.
4. Support Keyboard/Mouse/Flash Drive and many more
USB 2.0 Devices up to 350Mbps data rate.
-3-
