AWID SR-2400 Assembly instructions

SR-2400 Reader Installation Sheet
Installation Sheet
(Wiegand Interface)
SR-2400 Low-
Frequency Card Reader
These instructions are for AWID’s SR-
2400 Reader, using co patible proxi ity credentials
Parts List
(a) 1 Installation Sheet for SR-2400
(b) 1 Model SR-2400 Reader
(c) 2 #6-32 × 1” thread-
cutting screw, type 23
(d) 3 Screw-hole plug (1 spare)
Preparation
Reader Location
: Select the reader’s ounting location. The SR
1-
3/4 inch door fra e, or to a wall or other surface. On a etal surface, read range is reduced about 20%.
The SR-
2400 ay be installed indoors or outdoors. The diagra for screw and cable holes is on page 2.
DC Power Supply: DC po
wer for this reader is usually supplied fro the +DC and Ground ter inals of the
Wiegand reader port on the syste ’s panel. If this is not possible, use a separate power supply. Power ay be
shared with other readers if the supply has sufficient current
volts DC (as low as +5 volts is OK), 750 illia peres capacity, linear
Cable
to Controller and Power Supply: 4 to 6 conductors fro the reader to the syste (2 wires for DC po
2 wires for Wiegand data, and 1 or 2 wires for external LED and Beeper/Alar , if used). 22
wires. Overall 100%
shield for both power and data

If the DC power supply is separated fro the panel’s reader port, the reader’s
connected to both
the DC power supply’s Negative ter inal and the panel reader port’s Ground ter inal.

If the separate DC power supply is close to the reader, run two 22
and 3 to 5 wires for Wiegand data (including Ground) and for the external control lines, if used.
Both cables ust be overall-
shielded and earth

Conduit: If cables are pulled through etal conduit, the conduit should be earth
Installation
1. Connector – Cut off the 10-pin in-
line connector fro the end of the reader’s cable. D
2. ire Connections –
Connect the reader’s wires to the cable(s) for power and data.
a. First, connect black
to the panel port’s Ground ter inal, and, if separate, to the power supply Negative.
b. Connect green to the Data-
0 ter inal
c. Connect the gray
drain wire to the shield of the connecting cable.
If power and data are in separate cables, connect all three drains/shields together near the reader.
d. If the LED and/or Beeper/Alar
feature
e.
At the end of the cable(s) near the panel (and near the power supply, if separate), connect the
verified earth-ground.
f. Last, connect red
to the DC Positive ter inal.
Version 2.1 / Doc# 041405
(Wiegand Interface)
Frequency Card Reader
2400 Reader, using co patible proxi ity credentials
cutting screw, type 23
: Select the reader’s ounting location. The SR
-2400 Reader
ay be screwed to a
3/4 inch door fra e, or to a wall or other surface. On a etal surface, read range is reduced about 20%.
2400 ay be installed indoors or outdoors. The diagra for screw and cable holes is on page 2.
wer for this reader is usually supplied fro the +DC and Ground ter inals of the
Wiegand reader port on the syste ’s panel. If this is not possible, use a separate power supply. Power ay be
shared with other readers if the supply has sufficient current
capacity. The power supply should be close to +12
volts DC (as low as +5 volts is OK), 750 illia peres capacity, linear
-
rated, regulated DC output.
to Controller and Power Supply: 4 to 6 conductors fro the reader to the syste (2 wires for DC po
2 wires for Wiegand data, and 1 or 2 wires for external LED and Beeper/Alar , if used). 22
shield for both power and data
. 500 feet axi u length.
If the DC power supply is separated fro the panel’s reader port, the reader’s
black
wire
the DC power supply’s Negative ter inal and the panel reader port’s Ground ter inal.
If the separate DC power supply is close to the reader, run two 22
-gauge cables –
2 wires for DC power,
and 3 to 5 wires for Wiegand data (including Ground) and for the external control lines, if used.
shielded and earth
-gr
ounded (at the end far fro the reader).
Conduit: If cables are pulled through etal conduit, the conduit should be earth
-
grounded (like the cables).
line connector fro the end of the reader’s cable. D
Connect the reader’s wires to the cable(s) for power and data.
to the panel port’s Ground ter inal, and, if separate, to the power supply Negative.
0 ter inal
. Connect white to the Data-1 ter inal.
drain wire to the shield of the connecting cable.
If power and data are in separate cables, connect all three drains/shields together near the reader.
feature
s are used, connect the brown and/or
yellow
At the end of the cable(s) near the panel (and near the power supply, if separate), connect the
to the DC Positive ter inal.
Page 1 of 2
2400 Reader, using co patible proxi ity credentials
fro AWID.
ay be screwed to a
3/4 inch door fra e, or to a wall or other surface. On a etal surface, read range is reduced about 20%.
2400 ay be installed indoors or outdoors. The diagra for screw and cable holes is on page 2.
wer for this reader is usually supplied fro the +DC and Ground ter inals of the
Wiegand reader port on the syste ’s panel. If this is not possible, use a separate power supply. Power ay be
capacity. The power supply should be close to +12
rated, regulated DC output.
to Controller and Power Supply: 4 to 6 conductors fro the reader to the syste (2 wires for DC po
wer,
2 wires for Wiegand data, and 1 or 2 wires for external LED and Beeper/Alar , if used). 22
-gauge stranded
wire
must be
the DC power supply’s Negative ter inal and the panel reader port’s Ground ter inal.
2 wires for DC power,
and 3 to 5 wires for Wiegand data (including Ground) and for the external control lines, if used.
ounded (at the end far fro the reader).
grounded (like the cables).
line connector fro the end of the reader’s cable. D
iscard the connector.
to the panel port’s Ground ter inal, and, if separate, to the power supply Negative.
If power and data are in separate cables, connect all three drains/shields together near the reader.
yellow
wires.
At the end of the cable(s) near the panel (and near the power supply, if separate), connect the
shield to a
(continued)

SR-2400 Reader Installation Sheet
Note:
3. Reader Mounting –
Feed the reader’s cable through the cable opening in the door fra e or wall. Fasten
the reader to the fra e or wall, with screws through the
screws or other fasteners for ounting. After final testing, push the screw
4. Reader Test –
When power is applied to the SR
beeper sounds. With every presentation of an AWID LF proxi ity card to the reader, the LED changes
color o entarily, and the beeper sounds briefly. Read range with a co patible card is up to 5
5. System Test – Wire the read
er to the syste ’s controller. Progra the code for the AWID proxi ity card
or tag into the host syste , with full priority, all doors groups, and all ti e zones. Present the card or tag
to the reader. Observe door unlock or gate opening, indicating “Ac
Technical Support ● Call 408-825-
1100, option 1. E
SR-
2400 has been evaluated to the following Access Control Perfor ance Levels for UL standard 294:
1. Destructive Attack –
Level I (No Attack).
2. Line Security –
Level I (No Line Security).
3. Endurance –
Level IV (100,000 cycles).
4. Standby Power –
Level I (No Standby Power).
Access Control Reader, General Signaling Type
Version 2.1 / Doc# 041505
Note:
The SR-2400 reader
has no Hold control or RS
Do not use the blue, violet and orange
wires.
Feed the reader’s cable through the cable opening in the door fra e or wall. Fasten
the reader to the fra e or wall, with screws through the
holes fro the front of the reader. Use the supplied
screws or other fasteners for ounting. After final testing, push the screw
-
hole plugs over the screw heads.
When power is applied to the SR
-
2400, the LED initializes to steady
beeper sounds. With every presentation of an AWID LF proxi ity card to the reader, the LED changes
color o entarily, and the beeper sounds briefly. Read range with a co patible card is up to 5
er to the syste ’s controller. Progra the code for the AWID proxi ity card
or tag into the host syste , with full priority, all doors groups, and all ti e zones. Present the card or tag
to the reader. Observe door unlock or gate opening, indicating “Ac
cess Granted” by the syste .
1100, option 1. E
- ail Supp[email protected] .
2400 has been evaluated to the following Access Control Perfor ance Levels for UL standard 294:
Level I (No Attack).
Level I (No Line Security).
Level IV (100,000 cycles).
Level I (No Standby Power).
Access Control Reader, General Signaling Type
NM.
Page 2 of 2
has no Hold control or RS
-232 interface.
wires.
Feed the reader’s cable through the cable opening in the door fra e or wall. Fasten
holes fro the front of the reader. Use the supplied
hole plugs over the screw heads.
-red for standby, and the
beeper sounds. With every presentation of an AWID LF proxi ity card to the reader, the LED changes
color o entarily, and the beeper sounds briefly. Read range with a co patible card is up to 5
-1/2 inches.
er to the syste ’s controller. Progra the code for the AWID proxi ity card
or tag into the host syste , with full priority, all doors groups, and all ti e zones. Present the card or tag
cess Granted” by the syste .
2400 has been evaluated to the following Access Control Perfor ance Levels for UL standard 294: