Rev.1.2
Key Function1.In normal display, The key function is call out adjustment display scale page
2.Into parameter setting page, the parameter mark & data is alternate display, If need modify data
can press up key into setting procedure, The display is lock parameter data, this time must let off
key about 0.2 sec, press again, the parameter data will increment. (Key Response about 0.2 sec)
Key Function1.In normal display, The key function is call out adjustment analog output AZERO&ASPAN page
2.Into parameter setting page, the parameter mark & data is alternate display, If need modify data
can press down key into setting procedure, The display is lock parameter data, this time must let off
key about 0.2 sec, press again the parameter data will decrement. (Key Response about 0.2 sec)
& Key Function 1.In setting group or setting page press & key return normal display, but if in setting page the
modify data will be lost
No Key in anything 1.In setting group or setting page no key in anything about 2 minutes, return normal display, b
Setting page the modify data will be lost
Step
Parameter mark description
Parameter mark
Operation manual
1
Normal display
Press /FUNC key into P.COD setting page
2
P.COD(Pass code input page)
1.Key in 6 digit pass code with or or key
2.Press key,the pass code is right into setting group,otherwise return
normal display
3
SYS(System setting group)
ROP(Alarm setting group)
AOP(Analog output setting
group)
DOP(Communication setting
group)
1.Select setting group with key
2.Press key into setting page of selection setting group
4
SYS(System setting group)
Press key decide SYS setting group , press key into DP setting
page
4-1
DP(Decimal Point)
Default = 0
1.Decide decimal point position with or key(0~5)
2.Press key enter data and into TYPE setting page
4-2
TYPE(Type)
Default = 1U2G
1.Decide input type with or key (1U2G,1G2U,1D2G,1G2D
,1U2D,1P2D,1A2B)
2. Press key enter data and into CNTS setting page
4-3
CNTS(Count Rates Select)
Default = 50KHZ
1.Decide Count Rates Select with or key (50HZ,500HZ,50KHZ)
2. Press key enter data and into CODE setting page
4-4
CODE(Pass Code)
Default = 0
1.Decide pass code with or or key (0~999999)
2. Press key enter data and into LOCK setting page
4-5
LOCK(Panel Lock)
Default = NO
1. Decide panel lock with or key(NO or YES)
2. Press key enter data and return SYS setting group
5
ROP( Alarm setting group)
Press key decide ROP setting group, press key into OP.MODE
setting page
5-1
OP.MODE(Output Mode )
Default = N
1. Decide output mode with & key (N,F,R,Q,C,P,K)
2. Press key enter data and intoACT1.T setting page
5-2
ACT1.T(Active 1 Time )
Default = 0
1.Decide Active 1 Time with or or key (0.0~99.9)sec.
2. Press key enter data and intoACT2.T setting page
3.ACT1.T=0 sec. is self-holding output 1
.ACT1.T=0.1~99.9 sec. is one-shot output 1
5-3
ACT2.T(Active 2 Time )
Default = 0
1. Decide Active 2 Time with or or key (0.0~99.9)sec.
2. Press key enter data and return ROP setting group
3. ACT2.T=0 sec. is self-holding output 2
ACT2.T=0.1~99.9 sec. is one-shot output 2
6
AOP(Analog output setting
group)
Press key decide AOP setting group , press key into ANLO
setting page
