AXIOMTEK UST210-83K-FL Series User manual

UST210-83K-FL Series
Robust DIN-rail Fanless Embedded
System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any
third party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the
accuracy, completeness or usefulness of any information in this document. Axiomtek
does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any
time without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
©Copyright 2021 Axiomtek Co., Ltd.
All Rights Reserved
January 2021, Version A4
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The UST210-83K-FL does not come equipped with an operating system. An
operating system must be loaded first before installing any software into the
computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in
any static-shielded devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the UST210-83K-FL before making any
installation. Be sure both the system and the external devices are turned OFF.
Sudden surge of power could ruin sensitive components. Make sure the UST210-
83K-FL is properly grounded.
4. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only.
Do not spray any liquid cleaner directly onto the screen.
6. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -45℃or above 85℃. It may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a
must, only a trained technician is allowed to do so. Integrated circuits on
computer boards are sensitive to static electricity. To avoid damaging chips from
electrostatic discharge, observe the following precautions:
▪Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This will help to discharge any
static electricity on your body.
▪When handling boards and components, wear a grounding wrist strap,
available from most electronic component stores.
8. This product is intended to be supplied by a Listed Power Adapter or DC power
source. Output meets SELV limits, rated 12-24Vdc, minimum 1.6-0.81A, Tma = 25
degree C, and the altitude of operation = 5000m. Supported POE rated 24Vdc,
minimum 1.95A Tma = 25 degree C, and the altitude of operation = 5000m.
If you need further assistance while purchasing the power source, please contact
the manufacturer for further information.
CAUTION
Risk of explosion may occur if the battery is replaced by an incorrect type. Dispose
of used batteries according to the instructions.
WARNING
⚫Do not touch the hot surface of the system unit when it is turned on.
⚫Restricted access area: The equipment should only be installed in a Restricted
Access Area.

iv
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IP20
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture
with air or with oxygen or nitrous oxide.
4. Mode of operation: Continuous
5. Type of protection against electric shock: Class I equipment
General Cleaning Tips
You may need the following precautions before you begin to clean the computer.
When you clean any single part or component for the computer, please read and
understand the details below fully.
When you need to clean the device, please rub it with a piece of dry cloth.
1. Be cautious of the tiny removable components when you use a vacuum cleaner
to absorb the dirt on the floor.
2. Turn the system off before you start to clean up the computer or any components.
3. Never drop the components inside the computer or get circuit board damp or wet.
4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the
sake of cleaning. Some individuals may be allergic to the ingredients.
5. Try not to put any food, drink or cigarette around the computer.

v
Cleaning Tools
Although many companies have created products to help improve the process of
cleaning your computer and peripherals users can also use household items to clean
their computers and peripherals. Below is a listing of items you may need or want to
use while cleaning your computer or computer peripherals.
Keep in mind that some components in your computer may require a designated
product for cleaning. Please read the instructions that come with a cleaning product
to avoid misusage.
⚫Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, we still recommend that
you rub it with a piece of cloth.
⚫Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water
or rubbing alcohol and rub it on the computer. Unknown solvents may be harmful
to the plastics parts.
⚫Vacuum cleaner: Vacuuming the dust, dirt, hair, cigarette particles, and other
particles out of a computer can be one of the best methods of cleaning a
computer. Over time these items can restrict the airflow in a computer and cause
circuitry to corrode.
⚫Cotton swabs: Cotton swabs moistened with rubbing alcohol or water are
excellent tools for wiping hard-to-reach areas in your keyboard, mouse, and other
locations.
⚫Foam swabs: Whenever possible it is better to use lint free swabs such as foam
swabs.
Note: We strongly recommended that you should shut down the system before you start to
clean any single components.
Please follow the steps below:
1. Close all application programs;
2. Close operating software;
3. Turn off power;
4. Remove all devices;
5. Pull out the power cable.

vi
Scrap Computer Recycling
Please inform the nearest Axiomtek distributor as soon as possible for suitable
solutions in case computers require maintenance or repair; or for recycling in case
computers are out of order or no longer in use.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. IBM, PC/AT, PS/2, VGA are trademarks
of International Business Machines Corporation.
Intel®and Celeron®are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation. Other brand names and
trademarks are the properties and registered brands of their respective owners.

vii
Table of Contents
Safety Precautions................................................................................................ iii
Classification.........................................................................................................iv
General Cleaning Tips ..........................................................................................iv
Scrap Computer Recycling................................................................................... vi
SECTION 1 INTRODUCTION.........................................................................1
1.1 General Description...........................................................................1
1.2 System Specifications.......................................................................2
1.2.1 CPU ...................................................................................................................2
1.2.2BIOS ..................................................................................................................2
1.2.3System Memory ...............................................................................................2
1.2.4Display ..............................................................................................................2
1.2.5Ethernet Ports..................................................................................................3
1.2.6Remote SW.......................................................................................................3
1.2.7Storage..............................................................................................................4
1.2.8 Wireless ............................................................................................................4
1.2.9USB ...................................................................................................................4
1.2.10 COM/CAN .........................................................................................................4
1.2.11 Power................................................................................................................4
1.2.12 Power & Reset Button.....................................................................................5
1.2.13 DIO ....................................................................................................................5
1.2.14WatchDog Timer (WDT) ..................................................................................6
1.2.15Restore BIOS Optimal Defaults (SW1).....................................................6
1.2.16System LED......................................................................................................6
1.2.17Operation Temperature...................................................................................6
1.2.18Storage Temperature ......................................................................................6
1.2.19 Humidity ...........................................................................................................6
1.2.20 Weight...............................................................................................................6
1.2.21 Dimensions ......................................................................................................6
1.2.22 System I/O Outlets...........................................................................................7
1.3 Dimensions ........................................................................................8
1.4 I/O Outlets...........................................................................................9
SECTION 2 HARDWARE INSTALLATION .................................................11
2.1 Installing the Memory Module......................................................... 11
2.2 Installing the mSATA....................................................................... 12
2.3 Installing the Wireless Module........................................................ 13
2.4 Installing the Hard Disk ................................................................... 15
2.5 Installing the DIN-rail Mount and Wall Mount Kits......................... 16
2.6 Installing the Cable Fixing Plate...............................................................18
SECTION 3 AMI UEFI BIOS UTILITY..........................................................19
3.1 Entering Setup ................................................................................. 19
3.2 The Main Menu.................................................................................19
3.3 Advanced Features.......................................................................... 20
3.4 Chipset Feature................................................................................37
3.5 Security............................................................................................. 38
3.6 Boot Type ......................................................................................... 40
3.7 Save & Exit ....................................................................................... 42
APPENDIX A WATCHDOG TIMER .............................................................45

viii
About Watchdog Timer ...................................................................................45
How to Use Watchdog Timer .......................................................................... 45
APPENDIX B POWER BUTTON SETTING FOR WINDOWS SOFTWARE 47

UST210-83K-FL User’s Manual
Introduction 1
SECTION 1
INTRODUCTION
This chapter contains general information and detailed specifications of the UST210-83K-FL.
Section 1 includes the following sections:
◼General Description
◼System Specification
◼Dimensions
◼I/O Outlets
1.1 General Description
The UST210-83K-FL fanless embedded system is an ideal solution for communications control
and protocol converter applications in harsh environments. Designed for use in strict
environments, the UST210-83K-FL adopts an extra low power consumption Intel E3940
(1.6GHz/4-cores) processor, while also supporting an industrial operating temperature range
from -40°C to +70°C. The UST210-83K-FL offers a wide selection of I/O functions,
including 2 x USB, 1 x HDMI, 4 x LAN, 1 x COM port, 1 x CANBUS and 1 x DIO. Its
compact size makes it suitable for DIN-rail or wall mount, allowing for easy installation into
control cabinets. By supporting Windows®10, the UST210-83K-FL provides a friendly
environment for programmers to develop application software at a lower cost.
The UST210-83K-FL is a robust gateway built with an industrial-grade hardware design. It
adopts an advanced cooling system and supports mSATA and 2.5”SATA SSD (or HDD), which
makes it a perfect field control & monitoring system solution for the following markets:
◼Utility industries (hydro resources; energy; chemical plants; mining, etc.)
◼Public transportation industries (traffic/ highway control; train/bus control, etc.)
◼Homeland security (weather monitoring/alarm system, etc.)

UST210-83K-FL User’s Manual
2 Introduction
⚫Features
◼Fanless design
◼Wide temperature operation range of -40°C - +70°C
◼Supports 4x 10/100/1000 Base-T Ethernets
◼Two SKUs:
a) 1 x CANBUS port + 1 x COM port supporting RS-232/422/485 (4 wires)
b) 2 x COM ports support RS-232/422/485 (4 wires)
◼2 x USB 3.0
◼1 x HDMI
◼2 x PCIe Mini Card slots:
a) 1 x half size (USB/mSATA Interface)
b) 1 x full size (USB Interface) with SIM slot
◼Supports one 2.5”SATA drive and one mSATA (1 x half size Mini Card slot)
◼Wide range 9–36VDC power input with terminal block
(typical 12/24VDC for vehicle application)
◼8-bit programmable TTL level digital input/output port
◼DIN-rail or wall-mount mounting available
◼CE and FCC certified
◼Supports TPM2.0
◼Supports IEEE802.3 AF/AT PoE 30W (PoE model type only)
⚫Embedded O.S. Supported
◼UST210-83K-FL supports Windows®10 and Linux Ubuntu 18.04.
1.2 System Specifications
1.2.1 CPU
⚫Onboard Intel Atom® Apollo Lake-I x5-E3940 processor (1.6 GHz/4-cores).
1.2.2 BIOS
⚫AMI (American Megatrends Inc.) UEFI (Unified Extensible Firmware Interface)
BIOS.
1.2.3 System Memory
⚫One DDR3L 204-pin SO-DIMM (1.35V) slot.
⚫Supports 1866 MHz max up to 8GB.
1.2.4 Display
⚫Supports HDMI standards up to 1920x1200@60Hz.

UST210-83K-FL User’s Manual
Introduction 3
1.2.5 Ethernet Ports
⚫LAN chip: Intel Ethernet Controller I211.
⚫Four RJ-45 connectors support 10/100/1000 Base-T Ethernet with 1.5KV
magnetic isolated protection.
⚫Supports Power of Ethernet IEEE802.3 AF/AT 30W (PoE model type only) by
using the alternative A & B connection method to carry the power.
The UST210 is designed to function as a PSE device. To prevent
damaging the system hardware, do not connect the UST210 to other
PSE devices.
(Picture Source: IEEE std 802.3at-2009 Datasheet)
1.2.6 Remote SW
⚫1 x SW CN for remote control.

UST210-83K-FL User’s Manual
4 Introduction
1.2.7 Storage
⚫1 x mSATA (half size mini card slot).
⚫1 x SATA.
1.2.8 Wireless
⚫2 x Mini Card slots. (one half size and one full size)
⚫1 x SIM card socket.
⚫4 x antenna holes.
1.2.9 USB
⚫2 x USB3.0.
1.2.10 COM/CAN
⚫1 port TB supports 1COM+1CANBUS or 2COM
⚫COM mode supports RS-232/422/485 (which can be selected by BIOS)
⚫Supports High Speed Mode115.2 Kbps, Up to 1.5 Mbps
⚫Pin define is listed as follows:
PIN
RS232
RS422
RS485
PIN
RS232
RS422
RS485
CAN
B5
RX
TX+
D+
A5
RX
TX+
D+
x
B4
CTS
TX-
D-
A4
CTS
TX-
D-
x
B3
TX
RX+
x
A3
TX
RX+
x
L
B2
RTS
RX-
x
A2
RTS
RX-
x
H
B1
GND
GND
GND
A1
GND
GND
GND
GND
1.2.11 Power
⚫Wide-range 9 - 36VDC (typical 12/24VDC) power input with terminal block.
⚫OVP and RVP protection.
⚫Supports Axiomtek Smart Ignition.
Pin
Signal
1
+
2
-
3
IGN

UST210-83K-FL User’s Manual
Introduction 5
1.2.12 Power & Reset Button
⚫AT auto power on.
⚫Power button setting for software must be set up first.
⚫One reset button.
Note: Power button setting instructions for Windows software is offered in APPENDIX
B for reference.
1.2.13 DIO
⚫One DB9 female connector supports 8 bits TTL level programmable digital
input/output.
⚫The voltage for TTL is 5V.
⚫The programming is as follows:
- I/O sink current is 8~10mA (output drive current ± 50 mA).
- Input/Output is programmable.
Pin
Signal
1
DIO0
2
DIO1
3
DIO2
4
DIO3
5
DIO4
6
DIO5
7
DIO6
8
DIO7
9
GND

UST210-83K-FL User’s Manual
6 Introduction
1.2.14 WatchDog Timer (WDT)
⚫1~255 seconds or minutes; up to 255 levels.
1.2.15 Restore BIOS Optimal Defaults (SW1)
⚫Press the tact switch (SW 1) to restore optimal BIOS defaults.
1.2.16 System LED
⚫The table below summarizes the functional descriptions of the LED indicators and their
corresponding colors.
LED Name
Description
Color
ACT
Indicates storage status. The LED flashes when storage is
being accessed.
Orange
PWR
Indicates power status. When the DC input is acceptable, the
LED will turn on.
Green
1.2.17 Operation Temperature
⚫-400C ~ +700C
1.2.18 Storage Temperature
⚫-400C ~ +850C
1.2.19 Humidity
⚫0% ~ 95%
1.2.20 Weight
⚫0.514 kg
1.2.21 Dimensions
⚫48mm (1.22”) (W) x110mm (3.93”) (D) x155mm (4.92”) (H)

UST210-83K-FL User’s Manual
Introduction 7
1.2.22 System I/O Outlets
⚫One terminal block 2x5 pin male connector, 2 SKUs available:
a) COM x1 + CAN x1
b) COM x2
⚫One HDMI connector
⚫Four 10/100/1000 Base-T RJ-45 with 1.5KV magnetic isolated protection.
⚫Two USB 3.0 ports
⚫One DC power input with terminal block.
⚫One 9-pin D-Sub female connector for DIO.
⚫Four antenna holes.

UST210-83K-FL User’s Manual
8 Introduction
1.3 Dimensions
The following diagrams show you the dimensions and outlines of the UST210-83K-
FL.
Model without PoE
Model with PoE

UST210-83K-FL User’s Manual
Introduction 9
1.4 I/O Outlets
The following figures show you the I/O outlets on the front view and top view of the
UST210-83K-FL.
(Without PoE)
(with PoE)

UST210-83K-FL User’s Manual
10 Introduction
(Without PoE) (With PoE)

UST210-83K-FL User’s Manual
Hardware Installation 11
SECTION 2
HARDWARE INSTALLATION
The UST210-83K-FL is convenient for your various hardware configurations, such as
memory modules and mSATA drives. Section 2 will show you how to install the
hardware.
2.1 Installing the Memory Module
Step 1 Turn off the system.
Step 2 Loosen all screws from the cover and flip the cover to the left.
Step 3 Put the thermal pad on the memory module.
Step 4 Insert the memory into the slot and push the memory down to lock it in
place; make sure the memory is locked by the socket.

UST210-83K-FL User’s Manual
12 Hardware Installation
2.2 Installing the mSATA
Step 1 Insert the mSATA into the slot.
Step 2 Fasten the screws tightly.