AXIOMTEK CAPA84R User manual

4 9418E84R000E
© Copyright 2018 Axiomtek Co., Ltd.
Version A1 ovember 2018
Printed in Taiwan
Quick Start
The basic procedures required to power on CAPA84R:
(1). Require power at minimum 12V/0.87A. Check to ensure that
power supply is OFF before connecting to CAPA84R and that
all necessary peripheral devices are plugged properly.
(2). Install suitable heat dissipation device, ex: heatsink…etc.
(3). Make sure all of the jumper and switch are at default settings;
especially SW2 (1-2 close).
(4). Install DDR3L memory module into connector SODIMM1 until
fully seated.
(5). Firmly insert power to CN5/ATX1.
(6). Install a momentary on/off button/switch onto CN3, pin 7 and 8.
(7). Turn on the power supply.
(8). Press the on/off button/switch to power on CAPA84R.
CAPA84R Series Quick Installation Guide
9418E84R000E 1
© Copyright 2018 Axiomtek Co., Ltd.
Version A1 ovember 2018
Printed in Taiwan
Checklist

CPU
B
oard x1

Product
I
nformation
D
VD
x1

Quick
I
nstallation
G
uide
x1

Heatsink
or
H
eatspreader
(Optional)
Connectors
Connector Description
CN1
SMBus Connector
CN2
Digital I/O
Connector
CN3
Front Panel Connector
CN5/ATX1
DC +12V Power I
nput Connector
CN7
Fan Connector
CN8 DC +5V/15W Power Output Connector
CN9
M.2 2230 Key E Connector
CN10
SATA Power Connector
CN11
SIM Card Wafer Connector
CN12
SATA C
onnector
CN13
M.2 2242/3042 Key B Connector
CN14
USB 2.0 Port 1 and 2 Wafer Conne
ctor
CN15
Inverter Connector
CN16
Audio
Line
-
in/Line
-
out/Mic
-
in
Wafer
Connector
CN17
Ethernet Port 3 Wafer Connector
CN18
LVDS Connector
CN19 USB 3.0/2.0 Port 0 Type A Connector
CN20
DisplayPort Connector
CN21, CN23
Ethernet Port 1 and 2
CN22
Audio
Line
-
out Phone Jack
VGA1
VGA Connector
COM1, COM2
COM1 and COM2 Wafer Connector
BAT1
CMOS Battery Connector
SODIMM1 DDR3L SO-DIMM Connector
CAP
A
84R
Intel
®
Celeron
®
J1900/J1800
Processor
Capa
oard

2 9418E84R000E
© Copyright 2018 Axiomtek Co., Ltd.
Version A1 ovember 2018
Printed in Taiwan
Jumper and Switch Settings
Before applying power to the CAPA84R, please make sure all of the
jumper and switch are in factory default positions.
Jumper/Switc
h Description Setting
JP1 LVDS Voltage Selection
Default: +3.3V Level 1-2 Close
SW1 Restore BIOS Optimal Defaults
Default: Normal Operation Release
SW2 Auto Power On
Default: Disable 1-2 Close
Note: Please contact your local vendors if any damaged or missing items. DO
NOT apply power to the board if there is any damaged component.
Board Layout
Top View
Rear I/O
9418E84R000E 3
© Copyright 2018 Axiomtek Co., Ltd.
Version A1 ovember 2018
Printed in Taiwan
Bottom View
Side View
Note: Please refer to the CAPA84R series product information CD for the
complete user’s manual, drivers and utilities. User’s manual and related
documents are in Acrobat PDF format.