AXIOMTEK NA-320 Series User manual

NA-320 Series
Network Appliance
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.


Copyright 2010 AXIOMTEK Co., Ltd.
All Rights Reserved
July 2011, Version A2
Printed in Taiwan

iii
Safety Approvals
CE Marking
FCC Class B(NA-320/NA-320FL)
1. FCC Compliance
This equipment has been tested and complies with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.

iv
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing
the internal components. Use a grounding wrist strap and place all
electronic components in any static-shielded devices. Most
electronic components are sensitive to static electrical charge.
2. Disconnect the power cords from the NA-320 Series before
making any installation. Be sure both the system and the external
devices are turned OFF. Sudden surge of power could ruin
sensitive components. Make sure the NA-320 Series is properly
grounded.
3. Do not open the system’s top cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do
so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity on
your body.
When handling boards and components, wear a wrist-
grounding strap, available from most electronic component
stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel®and Pentium®are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft
Corporation.
Other brand names and trademarks are the properties and registered
brands of their respective owners.

v
Table of Contents
Disclaimers.........................................................................ii
Safety Approvals ............................................................... iii
Safety Precautions ............................................................iv
CHAPTER 1.................................................................... 1
INTRODUCTION ............................................................ 1
1.1 General Description........................................... 1
1.2 Features ............................................................ 2
1.3 Specifications .................................................... 3
1.3.1 System ........................................................................ 3
1.3.2 Mechanical / Environmental........................................ 5
1.4 Dimensions and Outlines................................... 7
1.5 I/O Outlets ......................................................... 9
1.5.1 Front Panel for NA-320 &NA-320FL .......................... 9
1.5.2 Rear Panel for NA-320 &NA-320FL......................... 11
1.5.3 Front Panel for NA-320R ......................................... 13
1.5.4 Rear Panel for NA-320R .......................................... 15
CHAPTER 2.................................................................. 17
HARDWARE DESCRIPTION ....................................... 17
2.1 Checklist.......................................................... 17
2.2 Memory Module (SODIMM) ............................. 18
2.3 Board Layout ................................................... 19
2.4 Jumper Settings .............................................. 21
2.4.1 Switch Button Selection Jumper (JP1 )..................... 22
2.4.2 LAN Bypass Trigger Selection Jumper (JP2, JP3) ... 23
2.4.3 LAN ByPass Selection Jumper (JP4) ....................... 24
2.4.4 CompactFlashTM Voltage Selection Jumper (JP5).... 24
2.4.5 Clear CMOS Jumper (JP6) ....................................... 25
2.4.6 Auto Power Button Jumer (JP7) ............................... 25
2.5 Connectors ...................................................... 26
2.5.1 DC-In Power Jack (CN1) for NA-320 & NA-320FL ... 27
2.5.2 Power out Connector (CN2)...................................... 27
2.5.3 LCM or SATA Power Connector (CN7) .................... 28
2.5.4 Mini Card Connector (CN8) ...................................... 28
2.5.5 Front Panel Bezel Connector (CN9) ......................... 29

vi
2.5.6 Serial Port1 (For Console) Connector (COM1)......... 30
2.5.7 Serial Port2 Connector (COM2) ................................ 31
2.5.8 CPU FAN Connector (FAN1) .................................... 31
2.5.9 System FAN Connector (FAN2)................................ 31
2.5.10 PS2 Keyboard/Mouse Connector (KM1).................. 32
2.5.11 Serial ATA Connector: SATA1, SATA3 ................... 32
2.5.12 Compact Flash™ Socket：SCF1 ............................ 33
2.5.13 USB Port0~Port1 Connector (USB1)....................... 34
2.5.14 VGA Connector (VGA1)........................................... 35
2.5.15 LED1~LED8 ............................................................. 35
2.5.16 USB Port2~Port3 Connector (USB2)....................... 36
2.5.17 Power Input 12V Connector (ATX1) for NA-320R ... 36
CHAPTER 3.................................................................. 37
AMI BIOS SETUP UTILITY ..........................................37
3.1 Starting............................................................ 37
3.2 Navigation Keys............................................... 37
3.3 Main Menu....................................................... 38
3.4 Advanced Menu............................................... 39
3.5 Boot Menu ....................................................... 49
3.6 Security Menu.................................................. 52
3.7 Chipset Menu .................................................. 53
3.8 Exit Menu ........................................................ 57
APPENDIX A ................................................................ 59
ENABLING LAN BYPASS FEATURE........................... 59
APPENDIX B ................................................................ 60
WARNING .................................................................... 60

NA-320 Series Network Appliance User’s Manual
Introduction 1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications
of the NA-320 Series Network Appliance Server. Chapter 1 contains
the following sections:
General Description
Features
Specifications
Dimensions
I/O Outlets
1.1 General Description
The NA-320 is a 1U and desktop and NA-320R is a 1U and rackmount
network security hardware platform for VPN, firewall and other
network security applications, which consists can support of Intel®
ATOM D410/D510 1.66GHz FSB 667; 512K/1M L2 Cache. This
platform supports the 1U desktop and 1U rack mount form factor, and
the system supports DDR2 667 memory with single channel up to
maximum 2 GB for one SODIMM slot. In the meantime, the platform
also can support 6 Gigabit LAN ports which can provide best
throughput. For the purpose to store event log data, it can deploy one
2.5” SATA2 HDD (NA-320&NA-320FL) or two 2.5” SATA2 (default) or
one 3.5” SATA2 HDD (optional) in (NA-320R). This platform can be
easily enabled through application programs to make a user-friendly
appliance for customers, and provide the highest ever performance of
encryption and decryption.

NA-320 Series Network Appliance User’s Manual
Introduction
2
1.2 Features
Low power and high performance for network security field
applications. NA-320 series supports Intel®ATOM D510 1.66GHz
FSB 533; 512K/1M L2 Cache.(D410 for optional)
Supports Six 10/100/1000Mbps Ethernet ports
Supports BIOS redirected to COM port features
Supports one 2.5” SATA2 Hard Disk for NA-320&NA-320FL
Supports Two 2.5” SATA2 or one 3.5” SATA2 (optional) Hard
Disk for NA-320R
Reasonable computing performance and throughput for
processor and LAN ports


Suitable for Network Appliance; VPN, network bandwidth
controller, firewall and UTM

NA-320 Series Network Appliance User’s Manual
Introduction 3
1.3 Specifications
1.3.1 System
System CPU
Intel®D510 1.66GHz FSB 533; 512K/1M L2 Cache
processor onboard.(D410 for optional)
BIOS
AMI 16Mbit PnP Flash BIOS with function of BIOS redirected
to COM port
System Memory
One DDR2 667 SODIMM up to 2 GB(NA-320,NA-320R)
One DDR2 667 SODIMM up to 2 GB(Wide tempature
support is available upon request (NA-320FL)
NOTE Due to chipset limitation, system memory controller supports
the following DDR2 Data Transfer Rates, SODIMM Modules
and DRAM Device Technologies:
DDR2 Data Transfer Rate: 667 (PC 5300), non-ECC
2 Ranks of x16 SDRAMs (Double-sided)
1 Rank of x16 SDRAMs (Single-sided)


HDD Interface
One 2.5” SATA2 HDD for NA-320
One 2.5” SATA2 HDD (Wide tempature support is available
upon request (NA-320FL)
Two 2.5” SATA2 or one 3.5” SATA2 (optional) Hard Disk for
NA-320R


Compact Flash
One Compact Flash Type II (Wide tempature support is
available upon request (NA-320FL)
Network Interface
Six 10/100/1000Mbps Ethernet (Intel®82583V)
One group LAN by pass for optional(NA-320&NA-320FL)


Watchdog Timer
255 stepping for porting

NA-320 Series Network Appliance User’s Manual
Introduction
4


USB
Two USB ports in the rear side


Console
RS-232 Console port is the rear side(RJ-type)


Power
1 x 12V, 5A power adapter for NA-320,NA-320FL
AC to DC 84W open frame for NA-320R


OS Compatibility
Redhat 2.6 Kernel

NA-320 Series Network Appliance User’s Manual
Introduction 5
1.3.2 Mechanical / Environmental
Form Factor
1U Desktop for NA-320 & NA-320FL
1U Rack mount for NA-320R
LED
Power, HDD, Link/Act with transfer rate
LAN by pass LED and promgramable LED (NA-320,NA-
320FL for optional)
Operation Temperature
0°C ~ 40°C (32°F ~ 104°F)for NA-320&NA-320FL
0°C ~ 45°C (32°F ~ 113°F)for NA-320R
Storage Temperature
-20°C ~ 70°C (-4°F ~ 158°F)
Humidity
10% - 95% RH, non-condensing
Chassis Material
Steel
Dimensions
44mm (1.73”) (H) x 230mm (9.00”) (W) x 152.1mm (5.98”) (D)
for NA-320
44mm (1.73”) (H) x 230mm (9.00”) (W) x 153.5mm (6.04”) (D)
for NA-320FL
44mm(1.73’’)(H) x 430mm (16.93”) (W) x 248mm (9.76”) (D)
for NA-320R
Weight (Net/Gross)
1.295Kg / 2.295Kg (NA-320)
2.0 Kg/3.0 Kg(NA-320FL)

NA-320 Series Network Appliance User’s Manual
Introduction
6
3.2Kg/4.2Kg (NA-320R)
NOTE All specifications and images are subject to change
without notice.

NA-320 Series Network Appliance User’s Manual
Introduction 7
1.4 Dimensions and Outlines
NA-320

NA-320 Series Network Appliance User’s Manual
Introduction
8
NA-320FL
NA-320R

NA-320 Series Network Appliance User’s Manual
Introduction 9
1.5 I/O Outlets
Locate the front panel I/O outlets on the NA-320 Series server to
connect serial and Ethernet interface devices.
1.5.1 Front Panel for NA-320 &NA-320FL
LAN By-Pass LED(for optional)
While running the LAN By-Pass function, the LED always
lights up.
Programmable LED (for optional)
A sample code will be provided that allow users to define
their own function.
Power LED
It will be lighting when the server is powered on to perform
diagnostic tests and check a proper operation.
LAN Link LED
It will be lighting when a twisted pair is connected to
another Ethernet device on the port. It shows network
transfer rate while making a connection.
Activity LED
It will be lighting when the server is transmitting or
receiving a packet through the twisted pair ports.
LEDs
LEDs

NA-320 Series Network Appliance User’s Manual
Introduction
10
HDD LED
The LED flashes when transmitting or receiving any signals.

NA-320 Series Network Appliance User’s Manual
Introduction 11
1.5.2 Rear Panel for NA-320 &NA-320FL
Console port – RS-232 Console port is for the command
of line interface and of diagnostic support by P.O.S.T
(Power on Self Test).
Reset Switch – It is is for reset the system to reboot your
computer instead of turning OFF the power switch. It is a
better way to reboot your system for a longer life of the
system’s power supply.(for optional)
Default Switch – The sample code will be provided that
allows users to define their own function. For example,
when the system has any problems, this switch can
support to reset it to the customer’s OS default settings if
12V/5A DC
Power Input
LAN Ports
USB Ports
Console
Port
Reset/Default
Switch
USB Ports
LAN Ports
Console
Port
12V/5A DC
Power Input

NA-320 Series Network Appliance User’s Manual
Introduction
12
our customer’s OS supports this application. (for optional)
Link/Active LED (Single color)for LAN port #1, port#2,
port#3, port#4, port#5, port#6
1. The orange LED is on when the LAN port connection
is working.
2. The LED flashes when transmitting or receiving any
signals to or from the appliance.
3. The LED is dark when the appliance is off.
Transmitted LED for LAN port #1, port#2, port#3,
port#4, port#5, port#6
1. The double-color LED light indicates
10/100/1000Mbps transfer rate.
`Transfer Rate LED Light Color
10Mbps Dark
100Mbps Green
1000Mbps Amber
2. When the amber-color LED light is radiating, it should
be 1000Mbps transfer rate at this moment.
3. When the green-color LED light is radiating, it should
be 100Mbps transfer rate at this moment
4. If the LED is dark and Link/Active LED is light on or
flashing, it should be 10Mbps transfer rate.
5. When this LED and Link/Active LED both are
dark. No networking devices are attached

NA-320 Series Network Appliance User’s Manual
Introduction 13
1.5.3 Front Panel for NA-320R
Power on LED
System and power on
HDD LED
Link/Active LED (single color)
1. The green LED is on when it is a normal HD
connection.
2. The LED flashes when transmitting or receiving any
signals.
LAN By-Pass LED
While running the LAN By-Pass function, the LED always
lights up.
GPIO LED
A sample code will be provided that allow users to define
their own function.
Link/Active LED (Single color)for LAN port #1, port#2,
port#3, port#4, port#5 and port#6
1. The orange LED is on when the LAN port connection is
working.
2. The LED flashes when transmitting or receiving any
signals to or from the appliance.
3. The LED is dark when the appliance is off.
Power/HDD/
LAN Bypass
/GPIO LED
LAN Ports
USB Ports
Console
Port
Reset/Default
Switch

NA-320 Series Network Appliance User’s Manual
Introduction
14
Transmitted LED for LAN port #1, port#2, port#3,
port#4, port#5 and port#6
1. The double-color LED light indicates 10/100/1000Mbps
transfer rate.
`Transfer Rate LED Light Color
10Mbps Dark
100Mbps Green
1000Mbps Amber
2. When the amber-color LED light is radiating, it should
be 1000Mbps transfer rate at this moment.
3. When the green-color LED light is radiating, it should
be 100Mbps transfer rate at this moment
4. If the LED is dark and Link/Active LED is light on or
flashing, it should be 10Mbps transfer rate.
5. When this LED and Link/Active LED both are
dark. No networking devices are attached
Console port – RJ RS-232 Console port is for the
command of line interface and of diagnostic support by
P.O.S.T (Power on Self Test).
Reset Switch – It is is for reset the system to reboot your
computer instead of turning OFF the power switch. It is a
better way to reboot your system for a longer life of the
system’s power supply.
Default Switch – The sample code will be provided that
allows users to define their own function. For example,
when the system has any problems, this switch can support
to reset it to the customer’s OS default settings if our
customer’s OS supports this application