AXIOMTEK GOT107W-319 User manual

GOT107W-319
All-in-One
7” WSVGA TFT Fanless Touch Panel
Computer with Intel® Celeron®
Processor N3350 onboard or Intel®
Pentium® Processor N4200
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or rights of any
third party, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
Wrong type of batteries may cause explosion. It is recommended that users only replace with
the same or equivalent type of batteries as suggested by the manufacturer once properly
disposing of any used ones.
Copyright 2019 Axiomtek Co., Ltd.
All Rights Reserved
June 2019, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important precautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT107W-319 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT107W-319 series is
properly grounded.
3. Do not open the top cover of the system. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a grounding wrist strap, available
from most electronic component stores.
Trademark Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is a trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 GOT107W-319 Specifications.............................................................2
1.2.1 Main CPU Board ......................................................................................... 2
1.2.2 I/O System................................................................................................... 2
1.2.3 System Specifications ................................................................................. 3
1.3 Dimensions..........................................................................................4
1.4 I/O Outlets............................................................................................5
1.5 Packing List.........................................................................................6
Chapter 2 Hardware and Installation ...................... 7
2.1 Jumper and Connector Settings........................................................7
2.1.1 Jumper Settings .......................................................................................... 8
2.1.2 Connector Settings...................................................................................... 9
2.2 Mountings –Panel/Wall/Desktop/VESA ..........................................13
2.2.1 Panel-Mounting (optional)......................................................................... 13
2.2.2 Assembling the Wall-Mount Bracket......................................................... 15
2.2.3 Assembling the stand................................................................................ 16
2.3 Storage Installation...........................................................................17
2.3.1 mSATA Installation .................................................................................... 17
2.3.2 MicroSD Card Installation ......................................................................... 18
2.4 DRAM Installation..............................................................................19
2.5 M.2 Wireless Card Installation..........................................................20
2.6 Power Input (AC to DC cable) ..........................................................21
Chapter 3 AMI BIOS Setup Utility .......................... 23
3.1 Navigation Keys ................................................................................23
3.2 Main Menu..........................................................................................24
3.3 Advanced Menu.................................................................................25
3.3.1 Serial Port Configuration........................................................................... 26
3.3.2 Hardware Monitor...................................................................................... 27
3.3.3 Trusted Computing.................................................................................... 28
3.3.4 ACPI Settings............................................................................................ 29
3.3.5 CPU Configuration .................................................................................... 30

v
3.3.6 SATA Configuration ................................................................................... 31
3.3.7 USB Configuration..................................................................................... 32
3.4 Chipset Menu.....................................................................................33
3.4.1 North Bridge.............................................................................................. 34
3.4.2 South Bridge.............................................................................................. 35
3.5 Security Menu....................................................................................36
3.6 Boot Menu..........................................................................................37
3.7 Save & Exit Menu ..............................................................................38
Chapter 4 Drivers Installation .............................. 39
4.1 System ...............................................................................................39
4.1.1 Windows 10............................................................................................... 39
4.2 Touch Screen.....................................................................................39
Appendix A Watchdog Timer & DIO Programming ... 41
About Watchdog Timer................................................................................41
How to Use Watchdog Timer.......................................................................41
WDT Sample Program .................................................................................43
How to Use DIO Software Programming....................................................43

vi
This page is intentionally left blank.

GOT107W-319 User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the GOT107W-319,
including the following sections:
General Description
Specifications
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT107W-319 is a fanless and compact-size medical touch panel computer, equipped
with a 7”TFT LCD display and low power consumption Intel® Celeron® Processor N3350
(with 2M cache, up to 2.4 GHz) or Intel® Pentium® Processor N4200 (with 2M Cache, up to
2.5 GHz). This panel computer is compatible with Windows 10 and can house an mSATA for
storage and one M.2 card slot for wireless connection. Its excellent ID and friendly user
interface make it a professional yet easy-to-use panel computer. The GOT107W-319 is ideal
for applications with limited spaces in factory automation, building automation and more.
GOT107W-319: 7” TFT WSVGA Fanless Touch Panel Computer
Reliable and stable design
The GOT107W-319 adopts a fanless cooling system which makes it suitable for
environments prone to vibration.
Embedded O.S. supported
The GOT107W-319 supports not only Windows 10(64bit), but also embedded O.S. In
terms of storage device, the GOT107W-319 supports an mSATA.
Industrial-grade product design
The GOT107W-319 was adaptively designed to be used in different industrial
environments.
The GOT107W-319 comes with an IP65-rated front panel and its whole enclosure meets the
IPX1 standard.
For connecting other devices, the GOT107W-319 also features several interfaces: USB,
Ethernet, and RS-232/422/485.

GOT107W-319 User’s Manual
2 Introduction
1.2 GOT107W-319 Specifications
1.2.1 Main CPU Board
CPU
Intel® Celeron® Dual Core Processor N3350 (2M Cache, up to 2.4 GHz) onboard.
Intel® Pentium® Quad Core Processor N4200 (2M Cache, up to 2.5 GHz) onboard.
System memory
One 204-pin DDR3L-1600 SO-DIMM socket
Maximum memory up to 8 GB
BIOS
American Megatrends BIOS
1.2.2 I/O System
Standard I/O
One RS-232/422/485 port
One RS-232 port
Two USB 3.0 ports
Ethernet
Two RJ45 Giga Ethernet ports
Expansion
One M.2(E Key) slot for wireless module
Storage
One mSATA
MicroSD Card slot
Power connector
GOT107W-319: 12 VDC with an external 36W AC adapter and a screw type
connector.

GOT107W-319 User’s Manual
Introduction 3
1.2.3 System Specifications
7”WSVGA (1024 x 600) LCD with LED backlight
Projected capacitive multi-touch
Fanless heat dissipation design
Disk drive housing
mSATA
MicroSD card slot
Net weight
0.7 kg
Dimension (main body size)
192 mm x 145 mm x 37.4 mm
Operation temperature
0℃to 50℃
Relative humidity
10% to 90% @ 40℃, -non-condensing
Vibration
2.0 G, 5 to 500 Hz, random (with mSATA storage)
Power input
External 12V 36W AC adapter
—Power input: 100 to 240 VAC
—Power output: 12 VDC, Max. 3A
Cable for AC screw type connector to DC source for 9~24V DC
NOTE All specifications and images are subject to change without notice.

GOT107W-319 User’s Manual
4 Introduction
1.3 Dimensions
This diagram shows you dimensions and outlines of the GOT107W-319.
This diagram shows you the dimensions of the GOT107W-319 cutout

GOT107W-319 User’s Manual
Introduction 5
1.4 I/O Outlets
Please refer to Figures 1-1 and Table 1-1 for I/O locations at the bottom of the
GOT107W-319.
Figure 1-1 Front view of the GOT107W-319
Figure 1-1 Bottom view and back view of the GOT107W-319
Table 1-1 Descriptions of I/O functions at the bottom of the GOT107W-319
No
Function
No
Function
1
Power button
6
COM 1 (RS-232/422/485)
2
Power input connector
7
COM2
3
AT/ATX switch
8
Micro SD Card slot
4
Ethernet (RJ-45) x 2
9
Speaker x 2
5
USB3.0 x 2

GOT107W-319 User’s Manual
6 Introduction
1.5 Packing List
A complete bundled package of the GOT107W-319 should contain the following items:
GOT107W-319 x 1
Driver disc x 1
Power adapter & power cord (GOT107W-319-J)
AC to DC cable (GOT107W-319-DC)
Please contact an Axiomtek distributor immediately if you cannot find the package or any of the
above-mentioned items is missing.

GOT107W-319 User’s Manual
Hardware and Installation 7
Chapter 2
Hardware and Installation
The GOT107W-319 provides rich I/O ports and flexible expansions for users to meet different
demands. The section is describing hardware installation, including the following subsections:
Jumper and Connector Settings
Port Definitions
Hardware Installation
Mounting Methods
Connecting the Power Input
2.1 Jumper and Connector Settings
Diagram 2-1 Component side of the board

GOT107W-319 User’s Manual
8 Hardware and Installation
Diagram 2-2 Solder side of the board
2.1.1 Jumper Settings
By making proper jumper settings, users can configure the board SBC87319 to suit the needs
of their applications.
Table 2-1 shows the default jumper settings for the SBC87319.
Table 2-1 Default jumper settings
Jumper
★Default Setting
Jumper Setting
JP3
★Normal
Clear CMOS
Short 1-2
Short 2-3
NOTE: Items marked with ★ are for default settings.

GOT107W-319 User’s Manual
Hardware and Installation 9
2.1.2 Connector Settings
The connectors on the CPU Board allow the CPU Board to connect with other parts of the
system. Ensure that all connectors are in place and firmly attached. Table 2-2 lists the function
of each connector on the Board SBC87319.
Table 2-2 Connector Settings
Label
Connectors
CN4
Speaker connector
CN5
SIM socket
CN7
Mini PCI-Express Card socket
CN11
USB2.0 connector (optional with touch controller)
CN15
USB2.0 connector
CN17
DIO connector
CN19
M.2 E key 2230 type
CN23
USB3.0 connector
CN24
Power DC in connector
SW1
Power button
LAN1/LAN2
Ethernet connector
COM1
COM Port connector
COM2
COM Port connector
SW2
AT/ATX switch
SCN1
SD card connector

GOT107W-319 User’s Manual
10 Hardware and Installation
Speaker connector: CN4
Pin
Description
1
SPKOUT_L+
2
SPKOUT_L-
3
SPKOUT_R+
4
SPKOUT_R-
5
GND
USB2.0 connector: CN11
Pin
Description
1
USB Power
2
D-
3
D+
4
GND
5
GND
USB2.0 connector: CN15
Pin
Description
Pin
Description
1
USB2_PWR
2
USB2_PWR
3
USB_DN
4
USB_DN
5
USB_DP
6
USB_DP
7
GND
8
GND
9
GND
10
GND

GOT107W-319 User’s Manual
Hardware and Installation 11
DIO connector: CN17
Pin
Description
Pin
Description
1
+5V
2
+5V
3
GPIO1
4
GPIO2
5
GPIO3
6
GPIO4
7
GPIO5
8
GPIO6
9
GPIO7
10
GPIO8
11
GND
12
GND
COM Port connector: COM1
Pin
RS232 [*]
RS422 [*]
RS485 [*]
1
DCD#
TX-
485-
2
RXD
TX+
485+
3
TXD
RX+
NC
4
DTR#
RX-
NC
5
GND
GND
GND
6
DSR#
NC
NC
7
RTS#
NC
NC
8
CTS#
NC
NC
9
RI# [**]
NC
NC
[*]: Signals of COM1 can be RS-232/422/485 by selecting BIOS table.
[**]: Pin 9 of COM1 can be RI/5V/12V by selecting BIOS table.

GOT107W-319 User’s Manual
12 Hardware and Installation
COM Port connector: COM2
Pin
RS232
1
DCD#
2
RXD
3
TXD
4
DTR#
5
GND
6
DSR#
7
RTS#
8
CTS#
9
RI#
AT/ATX switch: SW2
Pin
Description
1
Disable auto power on (Default)
2
Enable auto power on

GOT107W-319 User’s Manual
Hardware and Installation 13
2.2 Mountings –Panel/Wall/Desktop/VESA
There are several mounting ways for the GOT107W-319: Wall, desktop, VESA and panel
mountings.
2.2.1 Panel-Mounting (optional)
The GOT107W-319 is designed for panel mount application.
Step1 Sticks four sealing pads on the edges of the chassis.
Step2 Assemble the panel kit onto the chassis and fasten the five screws.

GOT107W-319 User’s Manual
14 Hardware and Installation
Panel Mount Dimension