AXIOMTEK GOT3156T-832 User manual

GOT3156T-832
All-in-One
15”XGA TFT Fanless
Compact-Size PANEL PC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make
any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted,
in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by
the manufacturer that you follow the manufacturer’s instructions to only replace the same
or equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
August 2013, Version A2
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT3156T-832 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT3156T-832 Series is
properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Atom™are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
CHAPTER 1 INTRODUCTION .............................................................................. 1
CHAPTER 2 HARDWARE AND INSTALLATION...................................................... 7
2.1 OPEN BACK COVER...............................................................................................8
2.2 CF CARD INSTALLATION.........................................................................................9
2.3 JUMPER AND SWITCH SETTINGS ...........................................................................10
2.4 COM PORT CONNECTOR ...................................................................................12
2.5 ETHERNET.......................................................................................................13
2.6 MOUNTINGS:PANEL /WALL /VESA...................................................................13
2.7 HDD INSTALLATION ...........................................................................................15
2.8 DRAM INSTALLATION ........................................................................................17
2.9 WIRELESS LAN CARD INSTALLATION .....................................................................19
2.10 POWER INPUT ..................................................................................................21
CHAPTER 3 AMI BIOS SETUP UTILITY................................................................23
3.1 STARTING.........................................................................................................23
3.2 NAVIGATION KEYS .............................................................................................23
3.3 MAIN MENU....................................................................................................24
3.4 ADVANCED MENU.............................................................................................25
3.5 CHIPSET MENU.................................................................................................32
3.6 BOOT MENU ....................................................................................................34
3.7 SECURITY MENU ...............................................................................................35
3.8 SAVE &EXIT MENU...........................................................................................36
CHAPTER 4 DRIVERS INSTALLATION................................................................39
4.1 SYSTEM ...........................................................................................................39
4.2 TOUCH SCREEN.................................................................................................39
4.3 EMBEDDED O.S................................................................................................41

v
This page is intentionally left blank.

GOT3156T-832 User’s Manual
Introduction 1
Back
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the
GOT3156T-832. Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT3156T-832 adopts a 15-inch XGATFT LCD with 450-nit brightness and
an Intel®AtomTM processor N2600 1.6 GHz to provide excellent computing
performance and thermal resistance. This fanless platform is especially designed
for operating under heavy-duty environment including steel refinery, oil pipe, ship,
machine maker operating systems and many more. Having below abilities makes
GOT3156T-832 surely a most robust and cost-effective solution.
Wide Operating Temperature Range
GOT3156T-832 features a technology of wide operating temperature range which
allows it to work between -20°C to +55°C. It incorporates compact ID and fanless
cooling system with a low power Intel®AtomTM processor N2600 1.6 GHz,
making the platform a power-efficient solution.

GOT3156T-832 User’s Manual
2 Introduction
Back
Reliable and Stable Design
The GOT3156T-832 adopts a fan-less cooling system and a CompactFlash™ card,
which makes it especially suitable for vibration-heavy environments, best for the
transportation, ship, and industrial machinery markets. For high capacity storage
requirement, GOT3156T-832 can work under 1.3G (10 ~ 500Hz, random for 2.5”
HDD) in operation mode with a patent of anti-vibration design. The patent
improves the system reliability and sustainability.
WLANAntenna Supported (optional)
GOT3156T-832 has a PCI Express Mini Card slot for optional add-ons such as
wireless LAN card for 802.11 b/g connections & 3G/GPRS application,
graphics-enhanced video card, universal analog TV/FM tuner/AV capture card, and
more. It also provides an optional fixed rotational WLAN antenna for wireless
network connection.
More Features
GOT3156T-832 utilizes one 204-pin DDR3 SODIMM system memory max. up to
2GB, one SATA HDD and one CompactFlashTM slot. It provides over-current
protection-fuse and a full set of I/O including 3 RS-232, 1 RS-232/422/485, 4 USB
2.0, 1 audio (line-out), 2 Gigabit Ethernet and 1 VGA. Additionally, this slim unit
supports panel mount, wall mount (optional), VESA mount (optional) and desktop
stand (optional).
1.2 Specifications
Main CPU Board
CPU
Intel®AtomTM N2600 1.6GHz processor onboard
System Chipset
Intel®NM10 Express
System Memory
One 204-pin DDR3 SO-DIMM socket
Maximum memory up to 2GB
BIOS
America Megatrends BIOS
I/O System
Standard I/O
Three RS-232 and one RS-232/422/485
Four USB 2.0

GOT3156T-832 User’s Manual
Introduction 3
Back
Ethernet
Two Gigabit Ethernet
Audio
One Line-out
Expansion
One Mini card
Storage
One slot for CF card
One SATA
Power connector
Phoenix power connector
System Specification
15”XGA(1024x768) LCD with LED backlight
5 wired resistive Touch
Fanless Heat Dispensing Design
IP65 aluminum front bezel
Disk drive housing:
One 2.5”SATA drive
Net Weight
7.4 Kgs (16.44 lb)
Dimension (Main Body Size)
378mm x 60.7mm x 309mm
Operation Temperature
-20℃to 55℃
Relative Humidity
20% to 90% @ 40℃, Non-Condensing
Power input
DC power 10~30V (phoenix type)
Note: All specifications and images are subject to change without notice.
Note: If the operation temperature is higher than 40℃, the wide temperature HDD
is recommended to be used on the device, and it is higher than 45℃, the wide
temperature CF or SSD is recommended to be used on the device.

GOT3156T-832 User’s Manual
4 Introduction
Back
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of GOT3156T-832.

GOT3156T-832 User’s Manual
Introduction 5
Back
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT3156T-832.
No
Function
No
Function
1
POWER SWITCH (ATX)
7
COM 1 (RS-232/422/485)
2
Power Input connector (phoenix)
type)
8
COM 2 (RS-232)
3
COM 4 (RS-232)
9
Ethernet (RJ-45)
4
COM 3 (RS-232)
10
Dual USB 2.0 ports
5
Dual USB 2.0 ports
11
AUDIO (LINE-OUT)
6
VGA

GOT3156T-832 User’s Manual
6 Introduction
Back
1.5 Packing List
When you receive the GOT3156T-832, the bundled package should contain the
following items:
GOT3156T-832 unit x 1
Driver CD x 1
Phoenix connector x 1
Panel mount kit x 9
Screws for HDD x 4
If you cannot find the package or any items are missing, please contact Axiomtek
distributors immediately.

GOT3156T-832 User’s Manual
Hardware and Installation 7
Back
Chapter 2
Hardware and Installation
The GOT3156T-832 provides rich I/O ports and flexible expansions for you to meet different
demand, for example CF card. The chapter will show you how to install the hardware. It
includes:
Open back cover
CompactFlash™Card
Serial Port
Ethernet
Mounting Method
Hard disk
DRAM
Wireless LAN Card
Power

GOT3156T-832 User’s Manual
8 Hardware and Installation
Back
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew 14 screws on the back cover. Please refer the photo below.
Step 2 Remove the back cover.

GOT3156T-832 User’s Manual
Hardware and Installation 9
Back
2.2 CF card Installation
The GOT3156T-832 provides one CF slot for users to install CompactFlash™card. Please
refer to the following instructions for installation:
Step 1 Unscrew a screw on the cover of CF card slot on left side of GOT.
Step 2 Stick mylar on the CF card.
Step 3 Insert the card into the socket.
Step 4 Close the cover of CF card slot and fix it. Installation completes.

GOT3156T-832 User’s Manual
10 Hardware and Installation
Back
2.3 Jumper and Switch Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install
jumper clip on 2 jumper pins to close. And remove jumper clip from 2 jumper pins
to open. The following illustration shows how to set up jumper.
Before applying power to GOT3156T-832, please make sure all of the jumpers and
switch are in factory default position. Below you can find a summary table and
onboard default settings.
Jumper
Description
Setting
JP4
Auto Power On
Default: Disable
2-3 close
JP5
CF Voltage Selection
Default: +3.3V
1-2 close
JP6
Restore BIOS Optimal Defaults (Clear CMOS)
Default: Normal Operation
1-2 close
JP7
COM1 RS-232/422/485 Mode Setting
Default: RS-232
3-5, 4-6 close
JP8
3-5, 4-6 close
JP9
1-2 close
JP10
COM1 Data/Power Selection
Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
JP11
COM2 Data/Power Selection
Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
JP12
COM3 Data/Power Selection
Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
JP13
COM4 Data/Power Selection
Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close

GOT3156T-832 User’s Manual
Hardware and Installation 11
Back
2.3.1 COM1 Configuration
The COM1~4 are a standard DB-9 connector. Those connectors are equipped with
The GOT3156T-832 has four serial ports. COM1 is RS-232/422/485, while COM2 to COM4 are
RS-232. The following table shows you set COM1 port mode:
Description
Jumper Setting
RS-232 (Default)
JP7
JP8
JP9
RS-422
JP8
JP7
JP9
RS-485
JP8
JP7
JP9
2.3.2 COM port Power Configuration
All of the serial ports can output data or power through jumper setting.
The following table shows you how to do that.
Description
JP10~JP13
Pin1: DCD
Pin9: RI
(Default)
Pin1: +5V
Pin9: +12V
Pin1: +5V
Pin9: RI
Pin1: DCD
Pin9: +12V
Note: Each port +5V Maximum: 2A, +12V Maximum: 1A.

GOT3156T-832 User’s Manual
12 Hardware and Installation
Back
2.3.3 Auto Power On (JP4)
If JP4 is enabled for power input, the system will be automatically power on
without pressing soft power button. If JP4 is disabled for power input, it is
necessary to manually press soft power button to power on the system.
2.3.4 Restore BIOS Optimal Defaults (JP6)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing
this procedure can restore BIOS optimal defaults.
2.4 COM port Connector
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If
you need COM1 port to support RS-422 or RS-485 mode, please refer to Jumper
Settings
Function
Setting
Enable auto power on
1-2 close
Disable auto power on (Default)
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use

GOT3156T-832 User’s Manual
Hardware and Installation 13
Back
2.5 Ethernet
The GOT3156T-832 is equipped with a high performance Plug and Play Ethernet
interface, full compliant with IEEE 802.3 standard, and can be connected with a
RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Pin
100Base-T
1000Base-T
1
TX+
BI-DA+
2
TX-
BI-DA-
3
RX+
BI-DB+
4
NC
BI-DB-
5
NC
BI-DC+
6
RX-
BI-DC-
7
NC
BI-DD+
8
NC
BI-DD-
2.6 Mountings: Panel / Wall / VESA
There are 4 application options for the GOT3156T-832, Panel/Wall/Desktop/VESA
mountings.
2.6.1 VESA-ARM/Wall-Mount
The GOT3156T-832 provides two ways for VESA mount: 100x100 mm. Screw four
screws to fix the kit (option) in the back chassis.
Wall mount:
1
2
3
4
5
6
7
8
RJ-45

GOT3156T-832 User’s Manual
14 Hardware and Installation
Back
VESA mount: