AXIOMTEK P1157E-871 User manual

P1157E-871
All-in-One
15”XGA TFT Expandable
PANEL PC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
May 2013, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the P1157 Series before making any installation. Be
sure both the system and the external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure theP1157 Series is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 Specifications......................................................................................2
1.3 Dimensions and Outlines ...................................................................4
1.4 I/O Outlets............................................................................................6
1.5 Packing List.........................................................................................7
Chapter 2 Hardware and Installation ...................... 9
2.1 Open back cover ...............................................................................10
2.2 Serial Ports Interface ........................................................................11
2.2.1 COM1 Data/Power Selection (JP10)..........................................................11
2.2.2 COM1 RS-232/422/485 Mode Setting (JP11, JP12, JP14) .......................11
2.2.3 COM3 Data/Power Selection (JP13)..........................................................11
2.2.4 COM1&COM2 Connector ......................................................................... 12
2.2.5 COM3 & COM4 Connectors...................................................................... 12
2.3 Ethernet..............................................................................................13
2.4 Mountings: Panel / Wall / Rack / Desktop / VESA...........................14
2.4.1 VESA-ARM / Wall-Mount / Desktop-mount............................................... 14
2.4.2 Panel-mount Kit Assembly ........................................................................ 15
2.4.3 Rack-mount Kit Assembly......................................................................... 16
2.5 HDD Installation.................................................................................17
2.6 DRAM Installation..............................................................................19
2.7 CPU Installation.................................................................................21
2.8 CPU Cooler Installation ....................................................................23
2.9 Wireless LAN Module Installation (optional)...................................24
2.10 Add-on Card Installation...................................................................26
2.11 Optical Drive Installation(optional)..................................................28
Chapter 3 AMI BIOS Setup Utility .......................... 31
3.1 Starting...............................................................................................31
3.2 Navigation Keys ................................................................................31
3.3 Main Menu..........................................................................................32

v
3.4 Advanced Menu.................................................................................33
3.5 Chipset Menu.....................................................................................43
3.6 Boot Menu..........................................................................................47
3.7 Security Menu....................................................................................48
3.8 Save & Exit Menu ..............................................................................49
Chapter 4 Drivers Installation .............................. 51
4.1 System ...............................................................................................51
4.2 Touch Screen.....................................................................................51
4.3 Embedded O.S...................................................................................54
APPENDIX A WATCHDOG TIMER .......................... 55
About Watchdog Timer................................................................................55
How to Use Watchdog Timer.......................................................................55
APPENDIX B INTEL® IAMT SETTINGS.................. 57
Entering MEBx .............................................................................................57
Set and Change Password..........................................................................58
Intel®iAMT Web Console ............................................................................59

vi
This page is intentionally left blank.

P1157E-871 User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the P1157E-871.
Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The P1157E-871 adopts a 15-inch XGA TFT LCD with 250-nits brightness and Intel®3rd&2nd
CoreTM i7/i5/i3 series, Pentium®and Celeron®processors and Intel® C216/Q77 chipset to
provide excellent and powerful computing performance. Furthermore, P1157E-871 adopts
built-in speaker and option WLAN module for wireless connectivity.
Industrial-grade front bezel
P1157E-871 adopts industrial-grade material front bezel which incorporates the advantages of
light weight, high degree of hardness better heat releasing, easy-to-shape and anti-corrosion
ability. Therefore, P1157E-871 is especially suitable for most rugged industrial environments.
Expandable for 2 PCIe (2 PCI optional)
P1157E-871 has 2 PCIe (2 PCI optional) for expansion purpose. User can easily plug in
standard half-size PCI or PCIe card for any requirement.
Speaker and WLAN Antenna Supported
P1157E-871 features built-in speakers for kiosk application to display multimedia content
program. It also supports WLAN module (optional) antenna for wireless network connectivity.

P1157E-871 User’s Manual
2 Introduction
Powerful computing: Intel® 3rd Generation Core i7/i5/i3/Celeron processors
P1157E-871 features Intel®3rd&2nd Core™ i7/i5/i3 series, Pentium®and Celeron®processors
and Intel®C216/Q77 chipset which deliver high computing performance capability. Ivy Bridge
CPU offers reliable and stable performance and rugged environment.
1.2 Specifications
Main CPU Board
CPU
Intel®3rd&2nd Core™ i7/i5/i3 series, Pentium®and Celeron®processors
System Chipset
Intel®C216/Q77 Express Chipset
System Memory
2 x 204-pin DDR3 1600/1333 MHz SO-DIMM socket
Supporting 8GB per DIMM, maximum memory size up to 16GB
BIOS
America Megatrends BIOS (AMI UEFI BIOS)
I/O System
Standard I/O
1 x RS-232/422/485 with 5V&12V, 1 x RS-232 with 5V/12V, 2 x RS-232
4 x USB 3.0
2 x USB 2.0
1 x HDMI
1 x DVI-I
Ethernet
2 x RJ45 for Giga Ethernet
Audio
1 x Line-out
1 x Mic-in
Expansion
1 x Wireless Module(optional)
2 x PCIe x 8 slots Riser card (2 x PCI slots Riser card optional)
Storage
2 x 2.5” or 1 x 3.5” SATA HDD
Power connector
1 x AC plug

P1157E-871 User’s Manual
Introduction 3
System Specification
15”XGA(1024 X 768)LCD
5 wired resistive Touch
IP65/NEMA4 aluminum front bezel
IP65 aluminum front bezel
Net Weight
6.2 Kgs (13.67 lb)
Dimension (Main Body Size)
378 x 125 x 309mm
Operation Temperature
0℃to 45℃
Relative Humidity
10% to 95% @ 40℃, Non-Condensing
Power Input
100~240VAC power connector
NOTE 1. All specifications and images are subject to change without notice.
2. Combo key: Pressing Brightness+ & Brightness- means System ON/OFF.
Pressing VOL+ & VOL- means Audio mute.
3. The speed of expansion card will depend on your CPU.

P1157E-871 User’s Manual
4 Introduction
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of P1157E-871.

P1157E-871 User’s Manual
Introduction 5

P1157E-871 User’s Manual
6 Introduction
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the P1157E-871.
No
Function
1
1 x RS-232/422/485 with 5V&12V (COM1)
2
1 x DVI-I
3
2 x RJ45 for GIGAEthernet
4
1 x Line-out
5
1 x RS-232 with 5V&12V (COM3)
6
2 x USB2.0
7
1 x AC Plug
8
1 x switch for power on/off
9
1 x RS-232 (COM2)
10
1 x HDMI
11
4 x USB3.0
12
1 x MIC-in
13
1 x RS-232 (COM4)
14
2 x PCIe x 8 or 2 x PCI

P1157E-871 User’s Manual
Introduction 7
1.5 Packing List
When you receive the P1157E-871, the bundled package should contain the following items:
P1157E-871 unit x 1
Driver CD x1
Panel mount kit x 6
Wall/VESA mount kit x 1 (optional)
Rack mount kit x 1 (optional)
Power cord x 1
DVI to VGA adaptor
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.

P1157E-871 User’s Manual
8 Introduction
This page is intentionally left blank.

P1157E-871 User’s Manual
Hardware and Installation 9
Chapter 2
Hardware and Installation
The P1157E-871 provides rich I/O ports and flexible expansions for you to meet different
demand. The chapter will show you how to install the hardware. It includes:
Open back cover
Serial Port Interface
Ethernet
Mounting Methods
Hard disk
DRAM
CPU
CPU Cooler
Wireless LAN Module(optional)
Add-on card
Optical Drive(optional)

P1157E-871 User’s Manual
10 Hardware and Installation
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew 3 screws on the back cover and push to the right side. Please refer
the photo below.
Step 2 Remove the back cover and unscrew 2 screws.

P1157E-871 User’s Manual
Hardware and Installation 11
2.2 Serial Ports Interface
The P1157E-871 has four serial ports. COM1 is RS-232/422/485, while COM2, COM3 and
COM4 are RS-232.
The following table shows you the pin assignments of this connector:
2.2.1 COM1 Data/Power Selection (JP10)
The COM1 port has +5V level power capability on DCD and +12V level on RI by setting
this jumper. When COM1 is set to +5V or +12V level, please make sure the
communication mode is RS-232 (see section 2.2.2).
2.2.2 COM1 RS-232/422/485 Mode Setting (JP11, JP12, JP14)
Use these jumpers to set COM1 port to operate as RS-232, RS-422 or RS-485
communication mode.
JP11 JP12 JP14
2.2.3 COM3 Data/Power Selection (JP13)
The COM3 port has +5V level power capability on DCD and +12V level on RI by setting
this jumper.
Description
Jumper Setting
Power: Set CN15A pin 1 to +5V level
1-3 close
Data: Set CN15A pin 1 to DCD (Default)
3-5 close
Power: Set CN15A pin 9 to +12V level
2-4 close
Data: Set CN15A pin 9 to RI (Default)
4-6 close
Description
Jumper Setting
RS-232 mode
(Default)
JP11 3-5, 4-6 close
JP12 1-2 close
JP14 3-5, 4-6 close
RS-422 mode
JP11 1-3, 2-4 close
JP12 3-4 close
JP14 1-3, 2-4 close
RS-485 mode
JP11 1-3, 2-4 close
JP12 5-6 close
JP14 1-3, 2-4 close
Description
Jumper Setting
Power: Set CN13 pin 1 to +5V level
1-3 close
Data: Set CN13 pin 1 to DCD (Default)
3-5 close
Power: Set CN13 pin 8 to +12V level
2-4 close
Data: Set CN13 pin 8 to RI (Default)
4-6 close

P1157E-871 User’s Manual
12 Hardware and Installation
2.2.4 COM1&COM2 Connector
The CN15 is a double-deck DB-9 connector. The upper connector (CN15A) is for COM1
and the lower connector (CN15B) is for COM2. Note that the connectors (CN13 and
CN15A) come with power capability on DCD and RI pins by setting jumpers (see section
2.2.1).
CN15A (COM1)
CN15B (COM2)
2.2.5 COM3 & COM4 Connectors
The COM3 and COM4 interfaces are available through CN13 and CN14,
respectively. Each of these connectors is a 2x5 pin 2.0 pitch box header, see
table below for its pin assignments.
CN13/CN14
Pin
Pin
Signal
1
10
Data Carrier Detect (DCD)
2
11
Receive Data (RXD)
3
12
Transmit Data (TXD)
4
13
Data Terminal Ready (DTR)
5
14
Ground (GND)
6
15
Data Set Ready (DSR)
7
16
Request to Send (RTS)
8
17
Clear to Send (CTS)
9
18
Ring Indicator (RI)
Pin
Signal
1
Data Carrier Detect (DCD)
2
Data Set Ready (DSR)
3
Receive Data (RXD)
4
Request to Send (RTS)
5
Transmit Data (TXD)
6
Clear to Send (CTS)
7
Data Terminal Ready (DTR)
8
Ring Indicator (RI)
9
Ground (GND)
10
NC

P1157E-871 User’s Manual
Hardware and Installation 13
2.3 Ethernet
The P1157E-871 is equipped with two high performance plug and play Ethernet interfaces
(RJ-45) which are fully compliant with the IEEE 802.3 standard. Connection can be
established by plugging one end of the Ethernet cable into this RJ-45 connector and the other
end to a 1000/100/10-Base-T hub.
The Universal Serial Bus (compliant with USB 3.0 (5Gb/s)) connectors on the rear I/O are for
installing USB peripherals such as keyboard, mouse, scanner, etc. Note that the CN10 carries
LAN1, USB 3.0 port 2 and 3 signals while CN11 carries LAN2, USB 3.0 port 0 and 1 signals
CN10 CN11
Pin
LAN1 Signal (WG82579LM)/
LAN2 Signal (WG82583V)
Pin
LAN1 Signal (WG82579LM)/
LAN2 Signal (WG82583V)
L1
MDI0+
L5
MDI2+
L2
MDI0-
L6
MDI2-
L3
MDI1+
L7
MDI3+
L4
MDI1-
L8
MDI3-
A
100 LAN LED (Green)/
1000 LAN LED (Orange)
B
Active LED
Pin
USB Signal
Pin
USB Signal
1
USB_VCC(+5V level standby
power)
10
USB_VCC (+5V level standby power)
2
USB_Data2-
11
USB_Data3-
3
USB_Data2+
12
USB_Data3+
4
GND
13
GND
5
SSRX2-
14
SSRX3-
6
SSRX2+
15
SSRX3+
7
GND
16
GND
8
SSTX2-
17
SSTX3-
9
SSTX2+
18
SSTX3+

P1157E-871 User’s Manual
14 Hardware and Installation
2.4 Mountings: Panel / Wall / Rack / Desktop / VESA
There are 5 application options for the P1157E-871, including Panel/Wall/Rack/ Desktop/VESA
mounting ways.
2.4.1 VESA-ARM / Wall-Mount / Desktop-mount
The P1157E-871 provides VESA mount: 75x75 mm or 100x100mm. Screw six screws to
fix the kit in the back chassis.
▲VESA/ Wall mount bracket
▲Putting the bracket on the back of system