AXIOMTEK GOT3187W-832-PCT User manual

GOT3187W-832-PCT
All-in-One
18.5”WXGA TFT Fanless
Compact-Size PANEL PC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make
any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted,
in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by
the manufacturer that you follow the manufacturer’s instructions to only replace the same
or equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
August 2013, Version A3
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT3187W-832-PCT Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT3187W-832-PCT
Series is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2 are trademarks of International Business Machines Corporation.
Intel®and Atom®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
CHAPTER 1 INTRODUCTION .............................................................................. 1
CHAPTER 2 HARDWARE AND INSTALLATION...................................................... 7
2.1 OPEN BACK COVER...............................................................................................8
2.2 CF CARD INSTALLATION.........................................................................................9
2.3 JUMPER AND SWITCH SETTINGS ...........................................................................11
2.4 COM PORT CONNECTOR ...................................................................................13
2.5 ETHERNET.......................................................................................................14
2.6 MOUNTINGS:PANEL /WALL /VESA...................................................................14
2.7 HDD INSTALLATION ...........................................................................................16
2.8 DRAM INSTALLATION ........................................................................................18
2.9 WIRELESS LAN CARD INSTALLATION .....................................................................20
2.10 POWER INPUT ..................................................................................................22
CHAPTER 3 AMI BIOS SETUP UTILITY................................................................24
3.1 STARTING.........................................................................................................24
3.2 NAVIGATION KEYS .............................................................................................24
3.3 MAIN MENU....................................................................................................25
3.4 ADVANCED MENU.............................................................................................26
3.5 CHIPSET MENU.................................................................................................33
3.6 BOOT MENU ....................................................................................................35
3.7 SECURITY MENU ...............................................................................................36
3.8 SAVE &EXIT MENU...........................................................................................37
CHAPTER 4 DRIVERS INSTALLATION................................................................40
4.1 SYSTEM ...........................................................................................................40
4.2 TOUCH SCREEN.................................................................................................40
4.3 EMBEDDED O.S................................................................................................41

v
This page is intentionally left blank.

GOT3187W-832-PCT User’s Manual
Introduction 1
Back
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the
GOT3187W-832-PCT. Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT3187W-832-PCT adopts a 18.5-inch WXGATFT LCD with 300-nit
brightness and an Intel®Atom™processor D2550 1.86 GHz to provide excellent
computing performance and thermal resistance. This fanless platform is
especially designed for operating under heavy-duty environment including steel
refinery, oil pipe, ship, machine maker operating systems and many more.
Having below abilities makes GOT3187W-832-PCT surely a most robust and
cost-effective solution.
Wide Operating Temperature Range
GOT3187W-832-PCT features a technology of wide operating temperature range
which allows it to work between -10°C to +50°C. It incorporates no fixture frame
touch screen and fanless cooling system with a low power Intel®Atom™processor
D2550 1.86 GHz, making the platform a power-efficient solution.

GOT3187W-832-PCT User’s Manual
2 Introduction
Back
Reliable and Stable Design
The GOT3187W-832-PCT adopts a fan-less cooling system and a CompactFlash™
card, which makes it especially suitable for vibration-heavy environments, best for
the transportation, ship, and industrial machinery markets. For high capacity
storage requirement, GOT3187W-832-PCT can work under 2G (5 ~ 500Hz,
random for CompactFlash™) in operation mode with a patent of anti-vibration
design. The patent improves the system reliability and sustainability.
WLANAntenna Supported (optional)
GOT3187W-832-PCT has a PCI Express Mini Card slot for optional add-ons such
as wireless LAN card for 802.11 b/g connections & 3G/GPRS application,
graphics-enhanced video card, universal analog TV/FM tuner/AV capture card, and
more. It also provides an optional fixed rotational WLAN antenna for wireless
network connection.
More Features
GOT3187W-832-PCT utilizes one 204-pin DDR3 SODIMM system memory max.
up to 4GB, one SATA HDD and one CompactFlash™slot. It provides
over-current protection-fuse and a full set of I/O including 1 RS-232, 1
RS-232/422/485, 4 USB 2.0, 1 audio (line-out), 2 Gigabit Ethernet.
Additionally, this slim unit supports panel mount, wall mount (optional), VESA
mount (optional) and desktop stand (optional).
1.2 Specifications
Main CPU Board
CPU
Intel®AtomTM D2550 1.86GHz processor onboard
System Chipset
Intel®NM10 Express
System Memory
One 204-pin DDR3 SO-DIMM socket
Maximum memory up to 4GB
BIOS
America Megatrends BIOS
I/O System
Standard I/O
One RS-232 and one RS-232/422/485
Four USB 2.0

GOT3187W-832-PCT User’s Manual
Introduction 3
Back
Ethernet
Two Gigabit Ethernet
Audio
One Line-out
Expansion
One Mini card
Storage
One slot for CF card
One SATA
Power connector
Phoenix power connector
System Specification
18.5”WXGA(1366x768) LCD with LED backlight
Projected Capacitive Touch
Fanless Heat Dispensing Design
IP65 aluminum front bezel
Disk drive housing:
One 2.5”SATA drive
Net Weight
5.8 Kgs (12.79 lb)
Dimension (Main Body Size)
460.8mm x 58.5mm x 285mm
Operation Temperature
-10℃to 50℃
Relative Humidity
20% to 95% @ 40℃, Non-Condensing
Power input
DC power 10~30V (phoenix type)
Note: All specifications and images are subject to change without notice.
Note: If the operation temperature is higher than 40 ℃ , the wide temperature
HDD/CF are recommended to be used on the device.
Note: If the operation temperature is higher than 45 ℃ , the wide temperature
memory module is recommended to be used on the device.

GOT3187W-832-PCT User’s Manual
4 Introduction
Back
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of GOT3187W-832-PCT.

GOT3187W-832-PCT User’s Manual
Introduction 5
Back
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT3187W-832-PCT.
No
Function
No
Function
1
POWER SWITCH (ATX)
5
COM 2 (RS-232)
2
Power Input connector (Screw)
6
Ethernet (RJ-45)
3
Dual USB 2.0 ports
7
Dual USB 2.0 ports
4
COM 1 (RS-232/422/485)
8
AUDIO (LINE-OUT)

GOT3187W-832-PCT User’s Manual
6 Introduction
Back
1.5 Packing List
When you receive the GOT3187W-832-PCT, the bundled package should contain
the following items:
GOT3187W-832-PCT unit x 1
Driver CD x 1
Phoenix connector x 1
Panel mount kit x 12
Screws for HDD x 4
If you cannot find the package or any items are missing, please contact Axiomtek
distributors immediately.

GOT3187W-832-PCT User’s Manual
Hardware and Installation 7
Back
Chapter 2
Hardware and Installation
The GOT3187W-832-PCT provides rich I/O ports and flexible expansions for you to meet
different demand, for example CF card. The chapter will show you how to install the
hardware. It includes:
Open back cover
CompactFlash™Card
Serial Port
Ethernet
Mounting Method
Hard disk
DRAM
Wireless LAN Card
Power

GOT3187W-832-PCT User’s Manual
8 Hardware and Installation
Back
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew 8 screws on the back cover. Please refer the photo below.
Step 2 Remove the back cover.

GOT3187W-832-PCT User’s Manual
Hardware and Installation 9
Back
2.2 CF card Installation
The GOT3187W-832-PCT provides one CF slot for users to install CompactFlash™card.
Please refer to the following instructions for installation:
Step 1 Open the cover, unscrew 2 screws on the chassis.
Step 2 Stick mylar on the CF card.

GOT3187W-832-PCT User’s Manual
10 Hardware and Installation
Back
Step 3 Insert the CF card to the CF card slot, then finding the CF cover from the
system package and screw it.

GOT3187W-832-PCT User’s Manual
Hardware and Installation 11
Back
2.3 Jumper and Switch Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install
jumper clip on 2 jumper pins to close. And remove jumper clip from 2 jumper pins
to open. The following illustration shows how to set up jumper.
Before applying power to GOT3187W-832-PCT, please make sure all of the
jumpers and switch are in factory default position. Below you can find a summary
table and onboard default settings.
Jumper
Description
Setting
JP4
Auto Power On
Default: Disable
2-3 close
JP5
CF Voltage Selection
Default: +3.3V
1-2 close
JP6
Restore BIOS Optimal Defaults (Clear CMOS)
Default: Normal Operation
1-2 close
JP7
COM1 RS-232/422/485 Mode Setting
Default: RS-232
3-5, 4-6 close
JP8
3-5, 4-6 close
JP9
1-2 close
JP10
COM1 Data/Power Selection
Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
JP11
COM2 Data/Power Selection
Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close

GOT3187W-832-PCT User’s Manual
12 Hardware and Installation
Back
2.3.1 COM1 Configuration
The COM1 & COM2 are standard DB-9 connectors. Those connectors are equipped with
The GOT3187W-832-PCT has two serial ports. COM1 is RS-232/422/485, while COM2 is RS-232.
The following table shows you set COM1 port mode:
Description
Jumper Setting
RS-232 (Default)
JP7
JP8
JP9
RS-422
JP8
JP7
JP9
RS-485
JP8
JP7
JP9
2.3.2 COM port Power Configuration
All of the serial ports can output data or power through jumper setting.
The following table shows you how to do that.
Description
JP10~JP13
Pin1: DCD
Pin9: RI
(Default)
Pin1: +5V
Pin9: +12V
Pin1: +5V
Pin9: RI
Pin1: DCD
Pin9: +12V
Note: Each port +5V Maximum: 2A, +12V Maximum: 1A.

GOT3187W-832-PCT User’s Manual
Hardware and Installation 13
Back
2.3.3 Auto Power On (JP4)
If JP4 is enabled for power input, the system will be automatically power on
without pressing soft power button. If JP4 is disabled for power input, it is
necessary to manually press soft power button to power on the system.
2.3.4 Restore BIOS Optimal Defaults (JP6)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing
this procedure can restore BIOS optimal defaults.
2.4 COM port Connector
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If
you need COM1 port to support RS-422 or RS-485 mode, please refer to Jumper
Settings
Function
Setting
Enable auto power on
1-2 close
Disable auto power on (Default)
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use

GOT3187W-832-PCT User’s Manual
14 Hardware and Installation
Back
2.5 Ethernet
The GOT3187W-832-PCT is equipped with a high performance Plug and Play
Ethernet interface, full compliant with IEEE 802.3 standard, and can be connected
with a RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Pin
100Base-T
1000Base-T
1
TX+
BI-DA+
2
TX-
BI-DA-
3
RX+
BI-DB+
4
NC
BI-DB-
5
NC
BI-DC+
6
RX-
BI-DC-
7
NC
BI-DD+
8
NC
BI-DD-
2.6 Mountings: Panel / Wall / VESA
There are 4 application options for the GOT3187W-832-PCT,
Panel/Wall/Desktop/VESA mountings.
2.6.1 VESA-ARM/Wall-Mount
The GOT3187W-832-PCT provides VESAmount: 100x100 mm. Screw four screws to fix
the kit in the back chassis.
Wall mount:
1
2
3
4
5
6
7
8
RJ-45