AXIOMTEK ITC150WM User manual

ITC150WM
15.6" FHD TFT-LCD Slim Bezel Modular
Panel PC Powered by Intel® Smart Display
Module (SDM)
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or rights of any
third party, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
Wrong type of batteries may cause explosion. It is recommended that users only replace with
the same or equivalent type of batteries as suggested by the manufacturer once properly
disposing of any used ones.
Copyright 2020 Axiomtek Co., Ltd.
All Rights Reserved
July 2020, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important precautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect all power cords from the ITC150WM Series before making any installation.
Be sure both the system and the external devices are turned OFF. Sudden surge of
power could ruin sensitive components. Make sure the ITC150WM series is properly
grounded.
3. Do not open the top cover of the system. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a grounding wrist strap, available
from most electronic component stores.
Trademark Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is a trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Section 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 ITC150WM Specifications...................................................................2
1.2.1 Smart Display Module –( SDM 300S module) ............................................ 2
1.2.2 I/O System................................................................................................... 2
1.2.3 System Specifications................................................................................. 3
1.3 Dimensions..........................................................................................4
1.4 I/O Outlets............................................................................................6
1.5 Packing List.........................................................................................7
Section 2 Hardware and Installation ...................... 9
2.1 Jumper and Connector Settings........................................................9
2.1.1 Jumper Settings ........................................................................................ 10
2.1.2 Connector Settings.....................................................................................11
2.2 Mountings –VESA ............................................................................16
2.2.1 Panel-Mounting (optional)......................................................................... 16
2.2.2 Assembling the Wall Mount Bracket ......................................................... 17
2.2.3 Assembling the stand................................................................................ 18
2.3 Storage Installation...........................................................................19
2.3.1 Storage Installation.................................................................................... 19
2.3.2 MicroSD Card Installation ......................................................................... 19
2.4 M.2 Wireless Card Installation .........................................................20
Section 3 AMI BIOS Setup Utility .......................... 21
3.1 Navigation Keys ................................................................................21
3.2 Main Menu..........................................................................................22
3.3 Advanced Menu.................................................................................23
3.3.1 Trusted Configuration................................................................................ 24
3.3.2 ACPI Settings............................................................................................ 25
3.3.3 NCT5104D Super IO configuration ........................................................... 26
3.3.4 CPU Configuration .................................................................................... 27
3.3.5 Network Stack Configuration..................................................................... 29
3.3.6 CSM (Compatibility Support Module) Configuration ................................. 30
3.4 Chipset Menu.....................................................................................32
3.4.1 South Cluster Configuration...................................................................... 33

v
3.5 Security Menu....................................................................................36
3.6 Boot Menu..........................................................................................37
3.7 Save & Exit Menu ..............................................................................38
Section 4 Drivers Installation .............................. 41
4.1 System ...............................................................................................41
4.1.1 Windows 10............................................................................................... 41
4.2 Touch Screen.....................................................................................41

vi
This page is intentionally left blank.

ITC150WM User’s Manual
Introduction 1
Section 1
Introduction
Chapter 1 contains general information and detailed specification of the ITC150WM, which
includes the following sections:
General Description
Specifications
Dimensions
I/O Outlets
Package List
1.1 General Description
ITC150WM is Modular Panel PC ,equipped with a 15.6”TFT LCD display and low power
consumption processor, Intel® SDM CPU card (processor Celeron® Processor N3350 with 2M
cache, up to 2.4 GHz) or Intel® Pentium® Processor N4200 (with 2M Cache, up to 2.5 GHz). It
is compatible with Windows 10 and supports on board eMMC for storage and one M.2 card
slot for wireless connection. It has excellent ID design and friendly user interface which make it
a professional yet easy-to-use panel computer. The ITC150WM is an ideal model for retail
applications with limited spaces in factory automation, building automation and more.
ITC150WM : 15.6" FHD TFT-LCD Slim Bezel Modular Panel PC
Reliable and stable design
ITC150WM adopts a fanless cooling system which makes it suitable for harsh
environments susceptible to dust, vibration, etc.
Embedded O.S. supported
ITC150WM supports not only Windows 10 (64bit), but also embedded O.S. In terms of
storage device,
Industrial-grade product design
ITC150WM is adaptively designed to be used in different industrial environments. It
comes with an IP54-rated front panel.
For connecting other devices, ITC150WM also has several IO interfaces: USB, Ethernet
Mirco SD card and HDMI also can be SDM module replaced

ITC150WM User’s Manual
2 Introduction
1.2 ITC150WM Specifications
1.2.1 Smart Display Module –( SDM 300S module)
CPU CARD (SDM)
Intel® Celeron® Dual Core Processor N3350 (2M Cache, up to 2.4 GHz) onboard.
Intel® Pentium® Quad Core Processor N4200 (2M Cache, up to 2.5 GHz) onboard.
System memory
Onboard LPDDR4 2400 MHz
4GB Up to 8 GB Max (optional)
BIOS
American Megatrends BIOS only support UEFI mode, Legacy mode can not be used
as Intel limitation.
1.2.2 I/O System
Standard I/O
1x Power button with LED
1 x HDMI output
1 x USB 3.0 Type A
2 x USB 2.0 Type A
1 x microSD card slot (push-push type)
2 x 12 VDC-in barrel (screw-lock type)
SDM module-300S
1 x RJ45 Giga Ethernet
2 x USB 3.0
2 x ANT
1 x Power button
1 x reset button
Expansion
1 x M.2(E Key) slot for wireless module

ITC150WM User’s Manual
Introduction 3
1.2.3 System Specifications
15.6" FHD TFT-LCD Slim Bezel with LED backlight
Projected capacitive multi-touch 10 point
Fanless heat dissipation design
Disk housing
By SDM Module
Net weight
3.15 kg
Dimension (main body size)
386 mm (W) x 241 mm (H) x 40 mm (D)
Operation temperature
0℃to 50℃
Relative humidity
10% to 90% @ 40℃, -non-condensing
Vibration
3.0 G, 5 to 500 Hz, random
Power input
Optional External 12V 60W AC adapter
—Power input: 100 to 240 VAC
—Power output: 12 VDC, Max. 5A
Cable for screw type connector to DC source for 9~24V DC
NOTE All specifications and images are subject to change without notice.

ITC150WM User’s Manual
4 Introduction
1.3 Dimensions
ITC150WM outlines and dimensions
ITC150 + SDM300S

ITC150WM User’s Manual
Introduction 5
ITC150 + SDM500L

ITC150WM User’s Manual
6 Introduction
1.4 I/O Outlets
Please refer to Figures 1-1 and 1-2 for controls and I/O locations at the bottom of the
ITC-150WM.
Figure 1-1 Front view of the ITC-150WM
Figure 1-2 Left side view and button view of the ITC-150WM

ITC150WM User’s Manual
Introduction 7
1.5 Packing List
Accessories package of the ITC-150WM should contain the following items:
ITC150WM System x 1
DC cable
User manual x 1
Adapter x 1 (Optional)
Please contact an Axiomtek distributor immediately if any item is missing.

ITC150WM User’s Manual
8 Introduction
This page is intentionally left blank.

ITC150WM User’s Manual
Hardware and Installation 9
Section 2
Hardware and Installation
The ITC150WM provides rich I/O ports and flexible expansions for users to meet different
demands. This section is describing hardware installation, including the following subsections:
Jumper and Connector Settings
Port Definitions
Hardware Installation
Mounting Methods
Connecting the Power Input
2.1 Jumper and Connector Settings
Diagram 2-1 TOP side of the carrier board

ITC150WM User’s Manual
10 Hardware and Installation
2.1.1 Jumper Settings
By making proper jumper settings, users can configure the board SDB101 to suit the needs of
their applications.
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following
illustration shows how to set up jumper.
Before applying power to ESMB860 Series, please make sure all of the jumpers are in factory
default position. Below you can find a summary table and onboard default settings.
Note
Once the default jumper setting needs to be changed, please do it under power-off
condition.
Table 2-1 Default jumper settings
LVDS PWM power Selection (JP1)
JP1 is LVDS PWM power jumper , default is 5V.
LVDS power selection (JP2)
LVDS power can be selected by JP2, default is 3.3V.
NOTE: Items marked with ★ are for default settings.
Function
Setting
PWM Mode 5V (Default)
1-2 close
PWM Mode 3.3V
3-4 close
Function
Setting
3.3V (Default)
1-2 close
5V
3-4 close
12V
5-6 close

ITC150WM User’s Manual
Hardware and Installation 11
2.1.2 Connector Settings
The connectors on the Carrier board allow the SDM module to connect with other parts of the
system. Ensure that all connectors are in place and firmly attached. Table 2-2 lists the function
of each connector on the board SDB101.
Table 2-2 Connector Settings
Connector
Description
DC-IN1
Power connector
DC-IN2
Power connector
DC-IN3
Power connector
SDcard1
SD Card
USB1-2
USB2.0 Connector
USB3
USB3.0 Connector
HDMI1
HDMI connector
PWR1
Power button
SPKL1
Speaker left channel connector
SPKR1
Speaker right channel connector
USB4~6
Internal USB Connector
I2C-1~2
I2C bus connector
LVDS1
LVDS connector
PROG1
U6 programing connector
EDP1
eDP connector
INV1
LVDS invertor connector
Power Connectors(DC-in or out)PHDR 2.0mm SCD456DCS113BB1G
SD Connector (sdcard1)
Pin
Signal
Pin
Signal
1
12V
2
GND
3
12V
4
GND
5
12V
6
GND
7
12V
8
GND
9
12V
10
GND
Pin
Signal
1
SD_DATA2
2
SD_DATA3
3
SD_CMD
4
VDD(3.3V)
5
SD_CLK
6
GND
7
SD_DATA0
8
SD_DATA1
CD
SD_Detect

ITC150WM User’s Manual
12 Hardware and Installation
USB2.0 Connector(USB2 & USB1)
USB3.0 Connector(USB3)
HDMI Connector (HDMI1)
Speaker Connector(SPKL1&SPKR1) PHD 2.0mm 1191-700-02S
Pin
Signal
1
USB_VCC (+5V level )
2
USB _D-
3
USB _D+
4
GND
Pin
Signal
1
USB_VCC (+5V level standby power)
2
USB #1_D-
3
USB #1_D+
4
GND
5
USB1_SSRXN
6
USB1_SSRXP
7
GND
8
USB1_SSTXN
9
USB1_SSTXP
Pin
Signal
Pin
Signal
1
HDMI IN_DATA2+
2
GND
3
HDMI IN_DATA2-
4
HDMI IN_DATA1+
5
GND
6
HDMI IN_DATA1-
7
HDMI IN_DATA0+
8
GND
9
HDMI IN_DATA0-
10
HDMI IN Clock+
11
GND
12
HDMI IN Clock-
13
N.C.
14
N.C.
15
HDMI IN_SCL
16
HDMI IN_SDA
17
GND
18
+5V
19
HDMI_HTPLG
Pin
Signal
1
SPR+
2
SPR-

ITC150WM User’s Manual
Hardware and Installation 13
Internal USB2.0 (USB4~6) PHD 2.0mm 1192-700-05RMR
I2C Connector(I2C-1~2) PHD 2.0mm 1192-700-05RMR
Programing connector (prog1) Dupont 2.0mm
eDP (EDP1)
Pin
Signal
1
VCC (+5V level )
2
USBn
3
USBp
4
GND
5
GND
Pin
Signal
L1
3.3V
L2
SDA
L3
SCL
L4
GND
Pin
Signal
1
TX
2
RX
3
GND
Pin
Signal
Pin
Signal
1
NC
2
12V
3
12V
4
12V
5
12V
6
NC
7
N.C.
8
BKLTCTL
9
BKLTEN
10
GND
11
GND
12
GND
13
GND
14
HPD
15
GND
16
GND
17
eDP_BIST
18
+DVCCM1
19
+DVCCM1
20
Channel B D1+
21
EDP_AUX_N
22
EDP_AUX_P
23
Channel A D0-
24
DP2_TX_0_DP_CON
25
DP2_TX_0_DN_CON
26
GND
27
DP2_TX_1_DP_CON
28
DP2_TX_1_DN_CON
29
GND
30
NC

ITC150WM User’s Manual
14 Hardware and Installation
Internal LVDS Connector (LVDS1)
This board has a 40-pin connector (SCN5) for LVDS LCD interface. It is strongly
recommended to use the matching JST SHDR-40VS-B 40-pin connector for LVDS
interface. Pin 1~6 VCCM can be set to +3.3V level or +5V level by JP2 (see section 2.2).
18 or 24-bit Daul channel
Pin
Signal
Pin
Signal
1
VCCM
2
VCCM
3
VCCM
4
VCCM
5
VCCM
6
VCCM
7
N.C.
8
LVDS_DET
9
GND
10
GND
11
Channel B D3-
12
Channel B D0-
13
Channel B D3+
14
Channel B D0+
15
GND
16
GND
17
Channel B CLK-
18
Channel B D1-
19
Channel B CLK+
20
Channel B D1+
21
GND
22
GND
23
Channel A D0-
24
Channel B D2-
25
Channel A D0+
26
Channel B D2+
27
GND
28
GND
29
Channel A D1-
30
Channel A D3-
31
Channel A D1+
32
Channel A D3+
33
GND
34
GND
35
Channel A D2-
36
Channel A CLK-
37
Channel A D2+
38
Channel A CLK+
39
GND
40
GND