AXIOMTEK MPC240 User manual

MPC240
24”FHD Medical Grade Panel
Computer with Intel®CoreTM i7/i5
Processors
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2015 Axiomtek Co., Ltd.
All Rights Reserved
OCT 2015, Version A1
Printed in Taiwan

iii
Symbol Index
No.
Description
Symbol
1
CE Marking
2
Manufactured by：address of the MFG
3
EC REP address
4
Refer to instruction 4 manual / booklet
5
Serial Number
6
Direct current
7
Alternating current
AXIOMTEK Co., Ltd.
8F., No.4, Lane 235, Baoqiao Road, Xindian District,
New Taipei City 231, Taiwan (R.O.C.)
http://www.axiomtek.com.tw
Made in Taiwan
MEDNET GmbH, Borkstrasse 10, 48163 Muenster, Germany

iv
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The MPC240 Series does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the MPC240 Series before making any installation. Be
sure both the system and external devices are turned OFF. A sudden surge of power
could ruin sensitive components. Make sure the MPC240 Series is properly grounded.
4. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
5. The brightness of the flat panel display will be getting weaker as a result of frequent
usage. However, the operating period varies depending on the application environment.
6. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen. The MPC240 Series may come with or
w/o a touchscreen. Although the touchscreen is chemical resistant, it is recommended
that you spray the liquid cleaner on a cloth first before wiping the screen. In case your
system comes without the touchscreen, you must follow the same procedure and not
spray any cleaner on the flat panel directly.
7. Avoid using sharp objects to operate the touchscreen. Scratches on the touchscreen may
cause malfunction or internal failure to the touchscreen.
8. The flat panel display is not susceptible to shock or vibration. When assembling the
MPC240 Series, make sure it is securely installed.
9. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -30°C or above 60°C. It may damage the equipment.
10. External equipment intended for connection to signal input/out or other connectors shall
comply with relevant IEC standard.
11. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.

v
Important Safety Instructions
Read before operating equipment.
This product was designed and manufactured to meet strict quality and safety standards.
There are, however, some installation and operation precautions which you should be
particularly aware of.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Classification Class I ME Equipment.
6. External power adapter, Input : 100~240Vac, 135W
7. The medical panel computer is certified with medical certifications to meet medical grade
approval standards. This design and against enclosure allow it to operate reliably and
quietly, it applied in any medical environments.
8. WARNING: To avoid risk of electric shock, this equipment must only be connected to a
supply mains with protective earth.
9. Accessory equipment connected to the analog and digital interfaces must be in
compliance with the respective nationally harmonized IEC standards (i.e. IEC 60601-1
for medical equipment, IEC 60950-1 for ITE equipment). Furthermore all configurations
shall comply with the system standard in IEC 60601-1. Anyone who connects additional
equipment to the signal input part or signal output part is configuring a medical system,
and is therefore, responsible that the system complies with the requirements of the
system standard IEC 60601-1.
10. Power supply is specified as a part of ME EQUIPMENT.
11. For pluggable equipment, the mains connector shall be installed near the equipment and
shall be easily accessible.
12. Follow the national requirement to dispose unit/accessories/waste products/residues etc.
13. WARNING: Do not modify this equipment without authorization of the manufacturer.
14. WARNING: The operator must not touch the connectors and the patient at the same
time.

vi
Classification
1. Degree of production against electric shock: Not classified.
2. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air
or with oxygen or nitrous oxide.
3. Mode of operation: Continuous.
4. Type of protection against electric shock: Class I equipment.
General Cleaning Tips
You may need the following precautions before you begin to clean the computer. When you
clean any single part or component for the computer, please read and understand the details
below fully.
1. When you need to clean the device, please rub it with a piece of dry cloth.
2. Be cautious of the tiny removable components when you use a vacuum cleaner to
absorb the dirt on the floor.
3. Turn the system off before you start to clean up the component or computer.
4. Never drop the components inside the computer or get circuit board damp or wet.
5. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of
cleaning. Some individuals may be allergic to the ingredients.
6. Try not to put any food, drink or cigarette around the computer.

vii
Cleaning Tools
Although many companies have created products to help improve the process of cleaning your
computer and peripherals, users can also use household items to clean their computers and
peripherals. Below is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.
Keep in mind that some components in your computer may only be able to be cleaned using a
product designed for cleaning that component, if this is the case it will be mentioned in the
cleaning.
Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, we still recommend you
to rub it with a piece of cloth.
Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or
rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the
plastics parts.
Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of
a computer can be one of the best methods of cleaning a computer. Over time these
items can restrict the airflow in a computer and cause circuitry to corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools
for wiping hard to reach areas in your keyboard, mouse, and other locations.
Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs.
NOTE: We strongly recommend that you should shut down the system before you start to
clean any single components.
Please follow the steps below:
1. Close all application programs.
2. Close operating software.
3. Turn off power switch.
4. Remove all devices.
5. Pull out power cable.

viii
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond repair, we strongly
recommend that you should inform your Axiomtek distributor as soon as possible for the
suitable solution. For the computers that are no longer useful or no longer working well, please
contact your Axiomtek distributor for recycling and we will make the proper arrangement.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
AMI is trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are registered trademarks of Intel Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

ix
Table of Contents
Disclaimers......................................................................................................i
Disclaimers.....................................................................................................ii
CAUTION ........................................................................................................ii
Symbol Index.................................................................................................iii
Safety Precautions........................................................................................iv
Important Safety Instructions .......................................................................v
Classification.................................................................................................vi
General Cleaning Tips ..................................................................................vi
Cleaning Tools .............................................................................................vii
Scrap Computer Recycling........................................................................viii
Chapter 1 Introduction............................................. 1
1.1 Features...............................................................................................1
1.2 Specifications......................................................................................2
1.3 Dimensions..........................................................................................5
1.4 I/O Outlets............................................................................................6
1.5 Package Checklist.............................................................................10
Chapter 2 Starting MPC240....................................... 11
2.1 Turning On Your Device....................................................................12
2.2 Turning Off Your Device....................................................................13
2.3 Operating Your All-in-One PC ..........................................................14
2.3.1 Basic Operations....................................................................................... 14
2.3.2 Using the Optical Disk Drive ..................................................................... 17
2.3.3 Making Connections.................................................................................. 18
2.3.4 Using the Card Reader ............................................................................. 21
2.3.5 Using the Cable Tie................................................................................... 22
2.3.6 Connecting to Bluetooth Devices.............................................................. 23
2.3.7 Connecting to Internet............................................................................... 25
Chapter 3 Hardware Installation ........................... 29
3.1 Installing CPU/DRAM/WIFI module..................................................29
3.2 Installing Hard Disk Drive.................................................................33
3.3 Mounting............................................................................................34

x
Chapter 4 BIOS Setup Utility ................................. 35
4.1 BIOS Setup Menu..............................................................................35
4.2 Navigating and Entering Information in BIOS ................................36
4.3 Main Menu..........................................................................................37
4.4 Advanced Menu.................................................................................38
4.5 Boot Menu..........................................................................................39
4.6 Security Menu....................................................................................40
4.7 Save & Exit Menu ..............................................................................41
Appendix A Note........................................................ 43
Appendix B EMC Statement ...................................... 45

MPC240 Series User’s Manual
Introduction 1
Chapter 1
Introduction
The MPC240 is an ultra slim panel computer equipped with 24-inch 250nits brightness FHD
WSXGA+ LCD display and supports superior 4th Generation Intel 4th Generation Core i CPU
M-series & CELERON & Pentium processors and up to 16G of dual-channel DDR3L system
memory. it offers excellent 3D graphics and dual-view capability. The medical panel computer
is certified with medical certifications to meet medical grade approval standards. This design
allow it to operate reliably and quietly as it applied in any medical environments.
The panel also supports dual view and multiple I/O options. Furthermore, the MPC240
supports a PCIe mini card slot and an internal antenna for wireless expansion. With a built-in
2.0M pixels camera and speakers, this durable panel computer is also the best solutions for
VoIP and remote monitoring. This safe, reliable and user-friendly medical panel computer can
ensure customer’s project success and best suited for eHealthcare, Point of Care, and
telemedicine.
1.1 Features
24”(250nits) FHD WSXGA+ TFT LCD, resolution: 1920x1080
Intel®CoreTM i7/ i5/ i3 processors
EN60601-1 and CE certified
Built-in 2.0 mega pixels camera
WiFi/ Bluetooth communication module (Optional)

MPC240 Series User’s Manual
2 Introduction
1.2 Specifications
Item
Category
Specifications
CPU
Type & Speed
Intel 4th Generation Core i CPU M-series & CELERON &
Pentium
Power Consumption
37W
Level2 Cache
3~4MB
Major Chipset
Chipset
Intel HM86 (Reserved the design for QM87)
System Memory
Capacity
Two 204-pin DDR3L SODIMM sockets each for 4/8GB
Type
DDR-3L 1600MHz
Maximum Memory
16GB
System BIOS and
PMU
System & Video
UEFI BIOS structure with 4096KB Flash Memory
Support ACPI 3.0
Suspend to RAM, Suspend to Disk
Boot from LAN, Ext. USB device
Support “Rapid Start” when SSD as the storage
Support Vpro if chipset is using QM87
Power Management
Suspend to RAM (Standby)
Power Button suspend to Ram (User selectable in OS
Power Management Menu)
Resume the system by pressing the Power button
Suspend to Disk (Hibernation)
Power Button suspend to Disk (User selectable in OS
Power Management Menu)
Resume the system by pressing the Power button
USB device support selective suspend
Wake on LAN：Wake up the unit from S3, S4, S5
status
The default value is “Enable”.
Wake on WLAN: Wake up the unit from S3 status
The default value is “Disable”.
Booting
Support Boot From Ext. USB device/ LAN
Display & Touch
screen
LCD
24” FHD (1920x1080) TFT LCD
(After Touch Typical: 223 nits, Mini: 178 nits)
Touch screen
Optional Projective Capacitive touch panel

MPC240 Series User’s Manual
Introduction 3
Item
Category
Specifications
Display & Touch
screen
Proximity Sensor
A proximity sensor is used to detect the presence of a
user.
If a user is away from the device ＞100~110 cm, then the
display will turn off and resume when the user is
approaching the device ＜80~90 cm again.
Note:
The above proximity sensor distance is based on a user
who is wearing a white dress.
The detected distance of object needed to be calculated
with the consideration of panel PC’s vertical angle.
Web Cam
2.0M pixel Webcam support HD MJPEG
Storage
HDD
2.5" HDD Support 500/750 GB or more
Support SATA 3
SSD
2.5” SSD 64GB/128 GB
M2 SSD
M2-SATA SSD 64GB/128GB (M2 Type, 2242)
One M2 Socket for SSD 2242-D5-B+M Module
M2 SSD is a CTO option.
ODD
Optional 5.25” Super Multi Optical Disk Drive (Factory
Option)
Communications
Networking devices
Integrated Gigabit bps Ethernet
Wireless networking
devices
One Express mini card slot for WLAN module with
PCIe half MiniCard form factor is the Wireless LAN
(Wi-Fi) and Bluetooth (BT) combination
Intel WLAN 7260 module
CTO
Support WLAN/BT built-in Antennas
I/O Ports &
Expansion slot
I/O ports
Four USB 2.0 connectors
Four USB 3.0 connectors
One Line out 3.5mm audio jack
One Mic-in 3.5mm audio jack
One RJ-45 jack for internal 10/100/1000M bit
Ethernet
One DC-In jack
One 19 pin HDMI for external monitor
One SDXC card reader slot
Audio
Features
High Definition Audio
One microphone in the center of bottom side
Two speakers, sound pressure 70 dB at 0.5 M
Average at 0.8, 1K, 1.2K, and 1.5KHz with nominal
power
Power
AC Adapter
Medical Grade AC adapter
Input:100V-240V, 50Hz-60Hz, 1.6-0.8A, 135W
Output: 19V
Manufacturer : FSP Group Inc
Model name : FSP135-KDAM1

MPC240 Series User’s Manual
4 Introduction
Item
Category
Specifications
UPS
UPS battery
Optional internal UPS battery backup the system for
40 minutes.
(The UPS battery life is tested ONLY including External
keyboard and mouse connected to the system)
Note:
The test condition of UPS battery life is idle 70% and
burn-in 30%.
UPS battery is Factory option.
Manufacturer :
FUJIAN UNITED CORPORATION CO., LTD
Model name : P24AH
Note:
Only can be replaced by the manufacturer
Housing & Chassis
Housing
Support VESA mounting (100x100mm, M4x0.7mm)
on the back cover
Support optional Int. stand with rubber foot (Let the
stand to be designed with hinge and with the
adjusting angle 5°to 30°)
A protection glass on the front panel if configuration is
“without Touch panel”
Antimicrobial
Upper cover, back side with 1% Antimicrobial.
2 rubber foots with 0.5% Antimicrobial.
Environment
Temperature
Operating Environment Temperature: 5°C ~ 40°C
Storage Environment Temperature: -30°C ~ 60°C
Humidity
Operating Humidity: 10% ~ 90% (Non condensation)
Storage and
Transportation
Temperature: -30°C ~ 60°C
Humidity: 10% ~ 90% (Non condensation)
Certificated
EN60601-1, CE
*Design and Specifications are subject to change without prior notice.

MPC240 Series User’s Manual
Introduction 5
1.3 Dimensions
The following diagram shows dimensions and outlines of the MPC240.

MPC240 Series User’s Manual
6 Introduction
1.4 I/O Outlets
The following figures show locations of the MPC240 I/O outlets.
No.
Item
Description
1
Web camera
Use for video conference.
2
Display screen
Display the screen output.
Allow users to use the Projective Capacity
Multi-Touch (Touch Panel type).

MPC240 Series User’s Manual
Introduction 7
No.
Item
Description
1
Optical disc drive
Play or record DVD or CD discs.
2
Cable tie slot
Use to attach the cable tie.
3
DC-in jack
Connect the power adapter.
4
USB 2.0 ports (x4)
Connect USB 2.0 peripheral devices.
5
USB 3.0 ports (x4)
Connect USB 3.0 peripheral devices.
6
RJ-45 port
Connect to a local area network (LAN) using an Ethernet
cable.
7
HDMI output port
Connect an HDMI device such as an external HDMI LCD
TV.
8
VESA mounting holes
Support 100 x 100mm hole pattern for mounting purpose.
Screw size: M4 x 0.7mm
9
Stand mounting holes
Use to install the stand.
10
Speakers
Emit sound.

MPC240 Series User’s Manual
8 Introduction
No.
Item
Description
1
Power button
Press to turn your All-in-One PC on or off.
2
Earphone jack
Connect headphones or external speakers.
3
Microphone jack
Connect an external microphone.
4
Card reader
Use to insert memory cards to transfer pictures, music, and
data between your All-in-One PC and flash compatible
devices. The card reader supports SD (Secure Digital), SDXC,
SDHC, Mini-SD (with adapter), Micro-SD (with adapter).

MPC240 Series User’s Manual
Introduction 9
Status Indicators
The status indicators in the bottom and the left side of the All-in-One PC light up when a
particular function of the All-in-One PC is active.
No.
Item
Description
1
Power
The LED always lights on (blue) when the system is running.
When the system is in Sleep mode, the LED blinks.
2
Proximity
sensor
This sensor is able to detect the presence of nearby users
without any physical contact.
If the user is away from the device more than 90cm, the display
will automatically turn off. If the user gets closer to the sensor
device (less than 90cm), the display will automatically turn on.
3
UPS battery
Indicate the UPS battery status:
Orange light means the battery is being discharged.
Blinking orange light means the battery power is low.

MPC240 Series User’s Manual
10 Introduction
1.5 Package Checklist
The package bundled with your MPC240 should contain the following items:
MPC240 unit x1
AC Medical Adapter x 1
Driver/utility disc x1 containing driver and user’s manual
Cable tie x 1
NOTE: If you can not find this package or any items are missing, please contact Axiomtek
distributors immediately.