AXIOMTEK OPS883 Series User manual

OPS883 Series
Intel Open Pluggable Specification
Box
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make
any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
Copyright 2016 Axiomtek Co., Ltd.
All Rights Reserved
November 2016, Version A2
Printed in Taiwan

iii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested in compliance with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are mean to provide reasonable protection
against harmful interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or radiate radio frequency
energy and cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following methods:
A. Increase the separation between the equipment and receiver.
B. Connect the equipment to another outlet of a circuit that does not connect with the
receiver.
C. Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with the emission limits.

iv
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The OPS883 series does not come equipped with an operating system. An
operating system must be loaded first before installing any software into the
computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components
in any static-shielded devices. Most electronic components are sensitive to
static electrical charge.
3. Disconnect the power cord from the OPS883 series before any installation. Be
sure both the system and external devices turned OFF already. Make sure the
OPS883 series set to ground properly.
4. The brightness of the flat panel display will be getting weaker as frequently
used. However, the operating period varies depending on the application
environment.
5. The flat panel display is not susceptible to shock or vibration. When assembling
the OPS883 series, make sure toinstall it securely.
6. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below 0℃or above 45℃. It may damage the equipment.
7. External equipment intended for connection to signal input/out or other
connectors shall comply with relevant UL/IEC standard.
8. Do not open the back cover of the system. If opening the cover for
maintenance is necessary, only allow technicians to implement it. Integrated
circuits on computer boards are sensitive to static electricity. To avoid
damaging chips from electrostatic discharge, observe the following precautions:
9. Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
10. Please wear a wrist-grounding strap if you handling boards and eletronic
components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel®and Atom™are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation. Other brand names and
trademarks are the properties and registered brands of their respective owners.

v
Table of Contents
Disclaimers............................................................................................................... ii
Safety Approvals..................................................................................................... iii
Safety Precautions.................................................................................................. iv
CHAPTER 1 INTRODUCTION.................................................................................. 1
1.1 General Description............................................................................. 1
1.2 System Specifications......................................................................... 2
1.2.1 Main CPU Board..................................................................................................2
1.2.2 I/O System ...........................................................................................................2
1.3 Mechanical Assembly.......................................................................... 4
1.3.1 Dimensions..........................................................................................................4
1.3.2 I/O outlet ..............................................................................................................5
1.3.3 Mechanical Specifications.................................................................................6
1.3.4 Reference Design .............................................................................................11
1.4 Package List....................................................................................... 12
CHAPTER 2 HARDWARE INSTALLATION......................................................... 13
2.1 CPU, Storage, DRAM, Wireless & 3G module Installations............. 13
2.2 Pluggble Module Method................................................................... 22
CHAPTER 3 CONNECTORS .................................................................................. 23
3.1 Connectors......................................................................................... 23
3.1.1 JAE TX25 Connector (CN1)..............................................................................25
3.1.2 CPU FAN (CN2) .................................................................................................26
3.1.3 SIM Card Slot (CN4)..........................................................................................26
3.1.4 HDMI Connector (CN5).....................................................................................27
3.1.5 Power & Reset Button (CN6) ...........................................................................27

vi
3.1.6 Audio MIC-IN Connector (SCN2) .....................................................................28
3.1.7 AudioLine-Out Connector (SCN3)...................................................................28
3.1.8 Battery 2 PIN (BAT1).........................................................................................28
3.1.9 Mini Card Slot (SCN1).......................................................................................29
3.1.10 SSW1 Setting ....................................................................................................30
3.1.11 SATA & SATA Power Connector (SATA1) ....................................................31
3.1.12 RJ45 (I217LM) (LAN1).......................................................................................32
3.1.13 USB 3.0 Port (SUSB1) ......................................................................................32
3.1.14 USB 2.0 Port (SUSB2/3) ...................................................................................33
3.1.15 COM Port (COM2).............................................................................................33
CHAPTER 4 AMI BIOS SETUP UTILITY.............................................................. 35
4.1 Starting............................................................................................... 35
4.2 Navigation Keys................................................................................. 35
4.3Main Menu .......................................................................................... 36
4.4Advanced Menu ................................................................................. 37
4.5 Chipset Menu ..................................................................................... 47
4.6 Boot Menu .......................................................................................... 53
4.7 Security Menu .................................................................................... 54
4.8 Save & Exit Menu............................................................................... 55
APPENDIX A REFERENCE DOCUMENTS ......................................................... 57
APPENDIX B WATCHDOG TIMER ....................................................................... 59
Watchdog Timer Setting.................................................................................... 59
Using the Watchdog Function Start................................................................. 59
APPENDIX C iAMT SETTINGS.............................................................................. 61
C.1 Entering MEBx ................................................................................... 61
C.2 Set and Change Password................................................................ 61

vii
C.3 iAMT Settings..................................................................................... 63
C.4 iAMT Web Console............................................................................. 66

viii
This page is intentionally left blank.

OPS883 User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the OPS883 series.
Chapter 1 includes the following sections:
General Description
Specification
Michanical Assembly
Package List
1.1 General Description
Intel Open Pluggable Specification (OPS) Compliance
OPS883 series is based on the 4th generation Intel®Core™processor on board with
Intel®Q87 Express Chipset platform and it also future products. The Pluggable
Module is dedicated to provide an interchangeable solution to the digital signage
media players with compatible connector. This document provides the module form
factor, connector specification, reference thermal solution, and boundary conditions
in order to ensure the functionally of the module in all compatible display panel
system.
OPS883 series meets Intel Open Pluggable Specification for design and
development, simplifying system upgrade maintenance for manufacturers and
developers that supports Intel®4th Generation Core I series family, which stand for
high flexible and user-friendly digital signage applications.
Easy maintenance
OPS883 series offers a best solution for digital signage market. Compliant with Intel
OPS architecture, digital signage players are capable of deploying interchangeable
systems faster and easing upgrading/maintenance, while lowering costs for
development and implementation. Additionally, having the ability to simply slot-in
and out the unique pluggable engine box makes daily hassle easier and faster for
users.
OPS883 series has pluggable engine box design; you can change storage, DRAM
and update configurations more easily

OPS883 User’s Manual
Introduction
2
1.2 System Specifications
1.2.1 Main CPU Board
CPU
LGA1150 socket type 4th generation Intel® Core™ i5/i3/Celeron Processor
System Chipset
Intel® Q87 PCH
BIOS
American Megatrends Inc.
UEFI (Unified Extensible Firmware Interface) BIOS.
System Memory
One socket 204-pin DDR3 1333/1600MHz SO-DIMM, maximun up to 8GB
Wireless Module (Optional)
Optional IEEE802.11 b/g/n, Bluetooth 2.0
1.2.2 I/O System
Standard I/O
One HDMI (with 4K solution)
Two USB ports 2.0
One USB ports 3.0
One RS-232(COM2)
One Power on /Off button
One Reset button
Ethernet
10/100/1000Mbps Ethernet (with Intel®I217)
Audio
Line-out/ Mic-in
Expansion
One Full-size PCI Express Mini card (USB+PCIe signals supported)
Storage
One. 2.5” SATA HDD tray
One mSATA option through Mini PCIe by SSW1 selection
Net Weight
0.9Kg(1.99 lb) without cooler

OPS883 User’s Manual
Introduction
3
Dimension (Main Body Size)
200 mm(W) x 119 mm(D) x 30 mm(H)
Operation Temperature
0℃to 45℃(with airflow 1.2 m/s)
NOTE: All specifications and images are subject to change without notice.

OPS883 User’s Manual
Introduction
4
1.3 Mechanical Assembly
1.3.1 Dimensions
This diagram shows you dimensions and outlines of the OPS883 series
The overall dimension of the module including the mounting frame is 200mm x 119mm x
30mm, and it shows the location of the screw holes of front panel as well as the security lock.
※While plugging the OPS module, please make sure the heat sink side of OPS
module toward the outside. Axiomtek will be out of reasonability if there is any
damage occurred due to it.

OPS883 User’s Manual
Introduction
5
1.3.2 I/O outlet
The following figures show you the locations of the OPS883 series I/O outlets.
No.
Connector
No.
Connector
1
JAE TX-25
8
HDD indicator
2
Antenna opening
9
Audio(Line-out)
3
RS-232
10
Audio(Mic.-in)
4
Ethernet
11
2 x USB 2.0
5
HDMI Output
12
1 x USB 3.0
6
Power Switch
13
Antenna opening
7
Reset
14
2.5” SATA HDD tray
1
11
3
4
5
7
8
9
10
12
13
6
2
14

OPS883 User’s Manual
Introduction
6
1.3.3 Mechanical Specifications
OPS883 series is docked in the reference display panel
The OPS883 Pluggable Module docked at a display panel system.
In this reference design, the module is docked and undocked in the vertical direction.
NOTE: Please contact Axiomtek for available option display panel.

OPS883 User’s Manual
Introduction
7
Exploded View of the Pluggable Module
The Guide Rail Mechanism for the OPS883 series Module
You can use the rails alongside of OPS883 series Module to dock and undock the plug
connector at the back of the module to connect with docking board. There are two lock pins
on each side of the rail, and they serve as the locking mechanism to attach the lock holes on
the series module.

OPS883 User’s Manual
Introduction
8
Location of Lock Hole on the Pluggable Module
*The drawing is base on Intel Open Pluggable Specification

OPS883 User’s Manual
Introduction
9
Dimensions of the Guide Rail

OPS883 User’s Manual
Introduction
10
Location of JAE TX25 Plug Connector
Please refer to the following drawing for location of the JAE TX25 plug connector. Pin 1 of the
connector is located at 114.8 mm from the edge of the module, and 106.9 mm from the inner
side of the front panel. For mating tolerance of TX25 plug connector and TX24 receptacle
connector, please refer to the JAE specification
Vent Holes at the Pluggable Module Back Panel
On the OPS883 series module, it is recommended by Intel that some vent holes be opened at
the back so that hot air can escape more easily from the module that the FAR in on both
sides of the module back panel should be greater than 0.25.

OPS883 User’s Manual
Introduction
11
1.3.4 Reference Design
Display Panel Rear View –Internal
The digital signage OPS883 series prototype is based on a 32” display panel with the
functional blocks illustrated. It is mainly a 3-board partitioning design consisting of the
pluggable module, docking board and the panel control board.

OPS883 User’s Manual
Introduction
12
1.4 Package List
When you receive the OPS883 series, the bundled package should contain the
following items:
OPS883 System x 1
CD x 1
THERMAL GREASE(Syringe 1G)
M2 x 5 screw x 2
M4 x 6 screw x 2
M3 x 4 screw x 2 (For CPU installation)
If you cannot find the package or any items are missing, please contact Axiomtek distributors
immediately.