AXIOMTEK GOT3187WL-834 User manual

GOT3187WL-834
All-in-One
18.5” WXGA TFT Fanless
Multi-Touch PANEL PC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery and dispose of used ones.
Copyright 2020 Axiomtek Co., Ltd.
All Rights Reserved
August 2020, Version A2
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT3187WL-834 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT3187WL-834 Series
is properly grounded.
3. Do not open the system’s rear cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 Specifications......................................................................................2
1.3 Dimensions and Outlines...................................................................4
1.4 I/O Outlets............................................................................................6
1.5 Packing List.........................................................................................7
Chapter 2 Hardware and Installation ...................... 9
2.1 Open back cover ...............................................................................10
2.2 Jumper and Switch Setting ..............................................................11
2.2.1 PCIe / mSATA setting (JP6) .......................................................................11
2.2.2 Auto Power On (JP7) .................................................................................11
2.2.3 Restore BIOS Optimal Defaults (JP8)....................................................... 12
2.2.4 COM port Connector................................................................................. 12
2.3 Ethernet..............................................................................................13
2.4 Mountings: VESA..............................................................................14
2.5 Wireless LAN Card Installation........................................................15
2.6 Power Input........................................................................................17
Chapter 3 AMI BIOS Setup Utility .......................... 19
3.1 Navigation Keys ................................................................................19
3.2 Main Menu..........................................................................................20
3.3 Advanced Menu.................................................................................21
3.4 Chipset Menu.....................................................................................32
3.5 Security..............................................................................................38
3.6 Boot Menu..........................................................................................39
3.7 Save&Exit...........................................................................................40
Chapter 4 Drivers Installation .............................. 43
4.1 System ...............................................................................................43
4.1.1 Driver Content........................................................................................... 43
4.1.2 WIN 10 IoT................................................................................................ 43

GOT3187WL-834 User’s Manual
Introduction 1
Section 1
Introduction
This chapter contains general information and detailed specifications of the GOT3187WL-834.
Chapter 1 include the following sections:
General Description
Specifications
Dimensions and outlines
I/O Outlets
Package List
1.1 General Description
The GOT3187WL-834 adopts an 18.5-inch WXGA/FHD LCD and supports Intel®
Bay Trail-D processor. The Lite rugged industrial panel PC supports low power Intel®
Celeron® processor J1900. It also provides two PCI Express Mini card slots for 3G,
wireless network connectivity. This 18.5" multi-touch panel computer is suitable for
transportation, heavy-duty industry, smart factory automation, and oil pipe monitoring
systems.
Extended Operating Temperature Range with Fanless & IP65 front design
GOT3187WL-834 features a technology of extended operating temperature range which
allows it to work between -10°C to +50°C. It incorporates compact ID and fanless cooling
system with a low power Intel® Celeron® Processor J1900 (2M Cache, up to 2.42 GHz), IP65
front bezel to prevent from liquid or dust, making the platform a power-efficient solution.
Reliable and Stable Design
The GOT3187WL-834 adopts a fan-less cooling system, which makes it especially suitable for
vibration-heavy environments, best for the transportation, ship, and industrial machinery
markets. For high capacity storage requirement, GOT3187WL-834 can work under 1.0G (10 ~
500Hz) in operation mode with a patent of anti-vibration design. The patent improves the
system reliability and sustainability. (Note: Sometimes heavy-vibration may cause the LCD
screen flash with white color. It won’t affect product function.)

GOT3187WL-834 User’s Manual
2 Introduction
WLAN Antenna Supported (optional)
GOT3187WL-834 has 2 PCI Express Mini Card slots for optional add-on such as wireless LAN
card for 802.11 a/b/g/n connections, 3G/GPRS application, and more. These slots also provide
3 optional fixed rotational WLAN/3G antennas for wireless network connection.
More Features
GOT3187WL-834 utilizes one 204-pin DDR3L SODIMM system memory max. up to 8GB, one
SATA HDD and one mSATA. It provides over-current protection-fuse and a full set of I/O
including RS-232/422/485, USB 2.0, USB 3.0, audio (line-out), and Gigabit Ethernet.
Additionally, this slim unit supports VESA mount, wall mount (optional) and desktop stand
(optional).
1.2 Specifications
Main CPU Board
CPU
Intel® Celeron® Processor J1900 (2M Cache, up to 2.42 GHz) onboard
System Memory
1 x 204-pin DDR3L SO-DIMM socket
Maximum memory up to 8GB
BIOS
American Megatrends, Inc. (AMI) BIOS
I/O System
Standard I/O
2 x RS-232/422/485
2 x USB 2.0
2 x USB 3.0
Ethernet
2 x RJ45 for Giga Ethernet (Intel i210IT)
Audio
1x Line-out
Expansion
1 x Mini-card slot (w/SIM slot)
1 x Mini-card slot (supports mSATA, optional)
Storage
1 x 2.5”SATA
1 x mSATA
Power connector
Screw power connector (AC Version)
Phoenix power connector (DC Version)

GOT3187WL-834 User’s Manual
Introduction 3
System Specification
18.5”WXGA (1366x768) LCD with LED backlight
Resistive touch panel
Fanless Heat Dispensing Design
IP65 front bezel
Disk drive housing:
One 2.5”SATA drive
Net Weight
5.8 Kgs
Dimension (Main Body Size)
460.8x 58.5x 285 mm
Operation Temperature
-10°C to 50°C
Relative Humidity
20% to 90% @ 40°C, Non-Condensing
System Power input
DC Version: 9 to 36VDC or 12 to 36VDC (FHD Version) with phoenix power connector
AC Version: 12VDC, 60W power adapter
NOTE: All specifications and images are subject to change without notice.
If the operation temperature is higher than 40 ℃ , the wide temperature HDD is
recommended to be used on the device.

GOT3187WL-834 User’s Manual
4 Introduction
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of GOT3187WL-834
Outline dimension: 460.8x 58.5x 285 mm

GOT3187WL-834 User’s Manual
Introduction 5
Cut Out dimensions: 448.74 x 273.74 mm

GOT3187WL-834 User’s Manual
6 Introduction
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT3187WL-834.
No
Function
1
1 x Power Switch
2
1 x Screw conn. w/AC power adapter
3
2 x USB 2.0
4
2 x COM (RS-232/422/485)
5
2 x Ethernet
6
2 x USB 3.0
7
1 x Audio (Line-out)
8
2 x Speaker
9
1 x Backlight switch
10
2 x Brightness adjust ( +/- )

GOT3187WL-834 User’s Manual
Introduction 7
1.5 Packing List
When you receive the GOT3187WL-834, the bundled package should contain the following
items:
1 x GOT3187WL-834
1 x AC adapter x 1 (AC Version)
1 x Power cord x1 (AC Version)
1 x Phoenix connector (DC Version)
1 x Panel mount kit
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.

GOT3187WL-834 User’s Manual
8 Introduction
This page is intentionally left blank.

GOT3187WL-834 User’s Manual
Hardware and Installation 9
Section 2
Hardware and Installation
The GOT3187WL-834 provides rich I/O ports and flexible expansions for you to meet different
demand. The chapter will show you how to install the hardware. It includes:
Open Back Cover
Jumper and Switch Setting
Ethernet
VESA Mount
Wireless LAN Card
Power Input

GOT3187WL-834 User’s Manual
10 Hardware and Installation
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew 8 screws on the back cover. Please refer the photo below.
Step 2 Remove the back cover.

GOT3187WL-834 User’s Manual
Hardware and Installation 11
2.2 Jumper and Switch Setting
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following
illustration shows how to set up jumper.
Before applying power to GOT3187WL-834, please make sure all of the jumpers and switch
are in factory default position. Below you can find a summary table and onboard default
settings.
Jumper
Description
Setting
JP6
PCIe / mSATA setting
Default: PCIe
1-2 close
JP7
Auto Power On
Default: Disable
2-3 close
JP8
Restore BIOS Optimal Defaults (Clear CMOS)
Default: Normal Operation
1-2 close
2.2.1 PCIe / mSATA setting (JP6)
For CN8, switches mSATA or PCIe setting.
2.2.2 Auto Power On (JP7)
If JP7 is enabled for power input, the system will be automatically power on without pressing
soft power button. If JP7 is disabled for power input, it is necessary to manually press soft
power button to power on the system.
Function
Setting
PCIe (Default)
1-2 close
mSATA
2-3 close
Function
Setting
Enable auto power on (Default)
1-2 close
Disable auto power on
2-3 close

GOT3187WL-834 User’s Manual
12 Hardware and Installation
2.2.3 Restore BIOS Optimal Defaults (JP8)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure
can restore BIOS optimal defaults.
2.2.4 COM port Connector
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table.
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use

GOT3187WL-834 User’s Manual
Hardware and Installation 13
2.3 Ethernet
The GOT3187WL-834 has two RJ-45 connectors: LAN1 and LAN2. Ethernet connection can
be established by plugging one end of the Ethernet cable into this RJ-45 connector and the
other end (phone jack) to a 1000/100/10-Base-T hub.
Please refer to detailed pin assignment list below:
Pin
Signal
Pin
Signal
L1
MDI0+
L5
MDI2+
L2
MDI0-
L6
MDI2-
L3
MDI1+
L7
MDI3+
L4
MDI1-
L8
MDI3-
A
Active LED (Yellow)
B
100 LAN LED (Green) / 1000 LAN LED
(Orange)

GOT3187WL-834 User’s Manual
14 Hardware and Installation
2.4 Mountings: VESA
The GOT3187WL-834 provides VESA mount: 100x100 mm. Screw four screws to fix the kit in
the back chassis.
VESA mount:

GOT3187WL-834 User’s Manual
Hardware and Installation 15
2.5 Wireless LAN Card Installation
The GOT3187WL-834 provides one Mini card slot for user to install one wireless LAN card.
When installing the wireless LAN card, refer to the following instructions and illustration:
Step 1 Refer to section 2.2 to open the back cover and find out mini-card slot on
mainboard.
Step 2 Insert the wireless LAN card to the slot. Push it down firmly until it is fixing
with screw by the slot.

GOT3187WL-834 User’s Manual
16 Hardware and Installation
Step 3 Find the Antenna cable and connect it on wireless LAN card
Step 4 Remove the antenna plug from the top of back cover, and then install the
antenna on the antenna connector
NOTE: Please have the extended bracket when using half-size mini card.