AXIOMTEK GOT3126T-832 User manual

GOT3126T-832
All-in-One
12.1”SVGA TFT Fanless
Compact-Size
PANEL PC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
July 2013, Version A3
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT3126T-832 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT3126T-832 Series is
properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 Specifications......................................................................................2
1.3 Dimensions and Outlines ...................................................................4
1.4 I/O Outlets............................................................................................5
1.5 Packing List.........................................................................................6
Chapter 2 Hardware and Installation ...................... 7
2.1 Open back cover .................................................................................8
2.2 CF card Installation.............................................................................9
2.3 Serial Ports Interface ........................................................................10
2.3.1 COM1&COM2 Connector ......................................................................... 10
2.4 Ethernet..............................................................................................11
2.5 Mountings: Panel / Wall / VESA .......................................................12
2.5.1 VESA-ARM/Wall-Mount ............................................................................ 12
2.5.2 Panel-mount Kit Assembly ........................................................................ 13
2.6 HDD Installation.................................................................................14
2.7 DRAM Installation..............................................................................16
2.8 Wireless LAN Card Installation........................................................18
2.9 Power .................................................................................................19
Chapter 3 AMI BIOS Setup Utility .......................... 21
3.1 Starting...............................................................................................21
3.2 Navigation Keys ................................................................................21
3.3 Main Menu..........................................................................................22
3.4 Advanced Menu.................................................................................23
3.5 Chipset Menu.....................................................................................30
3.6 Boot Menu..........................................................................................32
3.7 Security Menu....................................................................................33
3.8 Save & Exit Menu ..............................................................................34

v
Chapter 4 Drivers Installation .............................. 37
4.1 System ...............................................................................................37
4.2 Touch Screen.....................................................................................37
4.3 Embedded O.S...................................................................................39

vi
This page is intentionally left blank.

GOT3126T-832 User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the GOT3126T-832.
Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT3126T-832 adopts a 12.1-inch SVGA TFT LCD with 450-nit brightness and an Intel®
AtomTM processor N2600 1.6 GHz to provide excellent computing performance and thermal
resistance. This fanless platform is especially designed for operating under heavy-duty
environment including steel refinery, oil pipe, ship, machine maker operating systems and
many more. Having below abilities makes GOT3126T-832 surely a most robust and
cost-effective solution.
Wide Operating Temperature Range
GOT3126T-832 features a technology of wide operating temperature range which allows it to
work between -20°C to +55°C. It incorporates compact ID and fanless cooling system with a
low power Intel®AtomTM processor N2600 1.6 GHz, making the platform a power-efficient
solution.
Reliable and Stable Design
The GOT3126T-832 adopts a fan-less cooling system and a CompactFlash™ card, which
makes it especially suitable for vibration-heavy environments, best for the transportation, ship,
and industrial machinery markets. For high capacity storage requirement, GOT3126T-832 can
work under 1.3G (10 ~ 500Hz, random for 2.5”HDD) in operation mode with a patent of
anti-vibration design. The patent improves the system reliability and sustainability.

GOT3126T-832 User’s Manual
2 Introduction
WLAN Antenna Supported (optional)
GOT3126T-832 has a PCI Express Mini Card slot for optional add-ons such as wireless LAN
card for 802.11 b/g connections & 3G/GPRS application, graphics-enhanced video card,
universal analog TV/FM tuner/AV capture card, and more. It also provides an optional fixed
rotational WLAN antenna for wireless network connection.
More Features
GOT3126T-832 utilizes one 204-pin DDR3 SODIMM system memory max. up to 2GB, one
SATA HDD and one CompactFlashTM slot. It provides over-current protection-fuse and a full
set of I/O including 2 RS-232, 1 RS-232/422/485, 4 USB 2.0, 1 audio (line-out), 2 Gigabit
Ethernet and 1 VGA. Additionally, this slim unit supports panel mount, wall mount (optional),
VESA mount (optional) and desktop stand (optional).
1.2 Specifications
Main CPU Board
CPU
Intel®AtomTM N2600 1.6GHz processor onboard
System Chipset
Intel®NM10 Express
System Memory
One 204-pin DDR3 SO-DIMM socket
Maximum memory up to 2GB
BIOS
America Megatrends BIOS
I/O System
Standard I/O
Two RS-232 and one RS-232/422/485
Four USB 2.0
Ethernet
Two RTL81111b Gigabit Ethernet
Audio
One Line-out
Expansion
One Mini card
Storage
One slot for CF card
One SATA
Power connector
Phoenix power connector

GOT3126T-832 User’s Manual
Introduction 3
System Specification
12.1” SVGA(800x600) LCD with LED backlight
5 wired resistive Touch
Fanless Heat Dispensing Design
IP65 aluminum front bezel
Disk drive housing:
One 2.5”SATA drive
Net Weight
2.8 Kgs (6.78 lb)
Dimension (Main Body Size)
311.5mm x 56.9mm x 250mm
Operation Temperature
-20℃to 55℃
Relative Humidity
20% to 90% @ 40℃, Non-Condensing
Power input
DC power 10~30V (phoenix type)
Note: All specifications and images are subject to change without notice.
Note: If the operation temperature is higher than 40 ℃ , the wide temperature HDD is
recommended to be used on the device.
Note: If the operation temperature is higher than 45 ℃ , the wide temperature CF is
recommended to be used on the device.

GOT3126T-832 User’s Manual
4 Introduction
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of GOT3126T-832.

GOT3126T-832 User’s Manual
Introduction 5
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT3126T-832.
No
Function
No
Function
1
POWER SWITCH (ATX)
7
COM 2 (RS-232)
2
Power Input connector (phoenix)
type)
8
2X Ethernet (RJ-45)
3
2 X USB 2.0
9
2 X USB 2.0
4
VGA
10
AUDIO (LINE-OUT)
5
COM 3 (RS-232)
6
COM 1 (RS-232/422/485)

GOT3126T-832 User’s Manual
6 Introduction
1.5 Packing List
When you receive the GOT3126T-832, the bundled package should contain the following
items:
GOT3126T-832 unit x 1
Driver CD x1
Phoenix connector x 1
Panel mount kit x 6
Screws for HDD x 4
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.

GOT3126T-832 User’s Manual
Hardware and Installation 7
Chapter 2
Hardware and Installation
The GOT326T-832 provides rich I/O ports and flexible expansions for you to meet different
demand, for example CF card. The chapter will show you how to install the hardware. It
includes:
Open back cover
CompactFlash™Card
Serial Port
Ethernet
Mounting Method
Hard disk
DRAM
Wireless LAN Card
Power

GOT3126T-832 User’s Manual
8 Hardware and Installation
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew ten screws on the back cover. Please refer the photo below.
Step 2 Remove the back cover.

GOT3126T-832 User’s Manual
Hardware and Installation 9
2.2 CF card Installation
The GOT3126T-832 provides one CF slot for users to install CompactFlash™card. Please
refer to the following instructions for installation:
Step 1 Unscrew a screw on the cover of CF card slot on left side of GOT.
Step 2 Stick mylar on the CF card.
Step 3 Insert the card into the socket.
Step 4 Close the cover of CF card slot and fix it. Installation completes.

GOT3126T-832 User’s Manual
10 Hardware and Installation
2.3 Serial Ports Interface
The GOT3126T-832 has four serial ports. COM1 is RS-232/422/485, while COM2 and COM3
are RS-232.
The following table shows you the pin assignments of this connector:
Jumper
Description
Jumper Setting
COM 1
RS-232 (Default)
JP8
JP7
JP9
RS-422
JP8
JP7
JP9
RS-485
JP8
JP7
JP9
2.3.1 COM1&COM2 Connector
The COM1 and COM2 is a standard DB-9 connector. This connector is equipped with
+5V level power capability on DCD and +12V level on RI by setting JP10 and JP11.
Jumper
Description
Default Jumper Setting
JP10
COM1 Port
W/O Power: (3-5, 4-6)
With Power: (1-3) DCD_+5V
(2-4) RI_+12V
(3-5, 4-6)
JP11
COM2 Port
W/O Power: (3-5, 4-6)(Default)
With Power: (1-3) DCD_+5V
(2-4) RI_+12V
(3-5, 4-6)
JP12
COM3 Port
W/O Power: (3-5, 4-6)(Default)
With Power: (1-3, 2-4)
(3-5, 4-6)

GOT3126T-832 User’s Manual
Hardware and Installation 11
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If you
need COM1 port to support RS-422 or RS-485 mode, please refer to Jumper Settings
COM1 (SBC87832)
1 5
6 10
2.4 Ethernet
The GOT3126T-832 is equipped with a high performance Plug and Play Ethernet interface, full
compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Pin
Signal
1
2
3
4
5
6
7
8
RJ-45
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
N.C
4
DTR
RX-
N.C.
5
GND
No use
No use
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use

GOT3126T-832 User’s Manual
12 Hardware and Installation
2.5 Mountings: Panel / Wall / VESA
There are 4 application options for the GOT3126T-832, Panel/Wall/Desktop/VESA mountings.
2.5.1 VESA-ARM/Wall-Mount
The GOT3126T-832 provides two ways for VESA mount: 100x100 mm. Screw four
screws to fix the kit (option) in the back chassis.
Wall mount:

GOT3126T-832 User’s Manual
Hardware and Installation 13
VESA mount:
2.5.2 Panel-mount Kit Assembly
The GOT3126T-832 is designed for panel mount application. To mount the
GOT3126T-832, the standard set of mounting kit (included in the system packaging) is
needed.

GOT3126T-832 User’s Manual
14 Hardware and Installation
2.6 HDD Installation
The GOT3126T-832 provides a convenient Hard Disk Drive (HDD) bracket for users to install
2.5”SATAHDD. Please follow the steps:
Step 1 Refer section 2.1 to open the back cover.
Step 2 Unscrew 4 screws to take off the HDD bracket.
Step 3 Fix the HDD on bracket by 4 screws.