B.E.G. LUXOMAT BL2 User manual

Subject to technical changes
Motion detector
BL2
Operating Manual
93317

© 2019
B.E.G. Brück Electronic GmbH
Gerberstraße 33
51789 Lindlar
GERMANY
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Internet: beg-luxomat.com
All device data can also be found here:
https://www.beg-luxomat.com/qr.php?prtno=93317

Content
Operating Manual 1
1 About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Other applicable documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Used symbols and signal words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Foreseeable misuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Qualified persons / electricians . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3.1 Certified electricians . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 Device overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.2 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1 Choice of mounting location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1.1 Sources of interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1.2 Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.2 Mounting options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2.1 Ceiling installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2.2 Surface mounting with mounting set 93256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2.3 Flush mounting with mounting set 93251 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1 Preparing the connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1.1 Preparing the connection cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1.2 Opening the terminal compartment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1.3 Strain relief/protection against accidental contact . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.2 Schematic wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2.1 Standard connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2.2 Parallel connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3 RC suppressor unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Operating Manual
Content
2
6 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1 Factory default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.2 Self-test cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.3 Adjustment via IR remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.3.1 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.3.2 Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.3.3 Adjusting the parameters with the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7 Care, maintenance and disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.2 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.3 Disposing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8 Diagnostics and troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9 Service and support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.1 Manufacturer's warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.1.1 Product code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.2 Contact details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
10 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10.1 General data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10.2 Dimensioned drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10.2.1 Ceiling installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10.2.2 Surface mounting with mounting set 93256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10.2.3 Flush mounting with mounting set 93251 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
10.2.4 Wire basket BSK 92199 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
11 Accessories / Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
12 EU declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

BL2 93317
Operating Manual 3
1 About this document
1.1 Other applicable documents
Short operating manual MAN_9728_120717-1 (supplied with the device).
1.2 Used symbols and signal words
2 Safety
The motion detector BL2 was developed, manufactured and tested in accordance with the appli-
cable safety standards. It corresponds to the state of the art.
2.1 Intended use
The device is a motion detector for ceiling mounting (interior applications) having a circular detec-
tion area.
Symbol indicating possible dangers to persons
Symbol indicating possible property damage
Symbol for useful information and tips
NOTICE Signal word for possible property damage
CAUTION Signal word for possible minor injuries
WARNING Signal word for possible serious injuries
DANGER Signal word for possible fatal injuries
CAUTION
Observe intended use!
The protection of personnel and the device cannot be guaranteed if the device is oper-
ated in a manner not complying with its intended use.
➜Only operate the device in accordance with its intended use.
➜B.E.G. Brück Electronic GmbH is not liable for damages caused by improper use.
➜Read these operating instructions before commissioning the device. Knowledge of the
operating instructions is an element of proper use.
NOTICE
Comply with conditions and regulations!
➜Observe the locally applicable legal regulations and the rules of the employer's liability
insurance association.

Operating Manual
BL2 93317
4
2.2 Foreseeable misuse
Any use other than that defined under "Intended use" or which goes beyond that use is considered
improper use.
In particular, use of the device is not permitted in the following cases:
￭in rooms with explosive atmospheres
￭in circuits which are relevant to safety
￭for medical purposes
2.3 Qualified persons / electricians
Connection, mounting, commissioning and adjustment of the device must only be carried out by
competent persons.
Prerequisites for competent persons:
￭They have a suitable technical education.
￭They are familiar with the rules and regulations for occupational safety and safety at work.
￭They are familiar with the operating instructions for the device.
￭They have been instructed by the responsible person on the mounting and operation of the
device.
2.3.1 Certified electricians
Work on electrical equipment may only be carried out by certified electricians or by instructed
persons under the direction and supervision of a certified electrician in accordance with the elec-
trical engineering regulations.
Due to their technical training, knowledge and experience as well as their familiarity with relevant
standards and regulations, certified electricians are able to perform work on electrical systems and
independently detect possible dangers.
In Germany, certified electricians must fulfill the requirements of accident-prevention regulations
DGUV (German Social Accident Insurance) provision 3 (e.g. electrician foreman). In other countries,
there are respective regulations that must be observed.
2.4 Disclaimer
B.E.G. Brück Electronic GmbH is not liable in the following cases:
￭The device is not being used properly.
￭Reasonably foreseeable misuse is not taken into account.
￭Mounting and electrical connection are not properly performed.
￭Changes (e.g., constructional) are made to the device.
NOTICE
Do not modify or otherwise interfere with the device!
➜Do not carry out modifications or otherwise interfere with the device. The device must
not be tampered with and must not be changed in any way.
➜The device must not be opened. There are no user-serviceable parts inside.
➜Repairs must only be performed by B.E.G. Brück Electronic GmbH.

BL2 93317
Operating Manual 5
3 Device description
3.1 Device overview
The device is a motion detector for ceiling mounting having a circular detection area. Settings can
be made with the IR-BL infrared remote control.
1Spring clamps for ceiling installation (removable)
2Lens
3Wiring compartment with cover
1 1
2
3

Operating Manual
BL2 93317
6
3.2 Functions
The general operation of the motion detector is described in the short operating instructions
supplied with the device.
Passive infrared motion detectors register movements of heat sources and convert them into
signals that are evaluated by a processor.
The device is a switching detector. The brightness value below which the illumination is to be
switched on can be freely selected (switch-on threshold). If the measured value is below the set
switch-on threshold, a detected movement causes the connected illumination to switch on. The
follow-up time also restarts with each newly detected movement. After the follow-up time has
elapsed, the illumination is switched off.
The illumination can be switched on or off manually by remote control at any time. The device then
remains switched on or off as long as movement is detected plus the set follow-up time.
The follow-up time is restarted by each movement detected. If no movement is detected during a
follow-up time, the detector returns to normal operation (light is switched on during movement and
remains on until no movement is detected for a follow-up time).
3.3 LED indicators
LED function indicators after each mains recovery
(10 s self-test cycle)
Factory setting active Red, green and white LEDs flash alternately
Detector is programmed Red LED flashes quickly (2x/s)
LED function indicators during operation
Motion detection Red LED flashes
Switch-on threshold exceeded Green LED flashes
IR command White LED flashes
1Status LEDs
1

BL2 93317
Operating Manual 7
4 Mounting
4.1 Choice of mounting location
The most important aspect of motion detection is the correct choice of mounting location.
➜Mount the detector so that the main direction of movement is always tangential (transverse to
the device).
➜Always mount the detector at the location with the lowest amount of daylight.
If the smallest movements are to be detected (e.g. working with the PC keyboard), we recommend
selecting the mounting location directly above the desk. This ensures that the detection can be guar-
anteed.
4.1.1 Sources of interference
The following sources of interference can lead to faulty switching because they also generate
temperature differences:
￭Radiant heaters
￭Ventilation systems that emit warm or cold air
￭Luminaires in the direct detection area
The detector must be installed at an appropriate distance from these sources.
4.1.2 Range
INFO
Observe mounting height!
Please be sure to observe the mounting height indicated for the devices.
￭The range is reduced by a lower mounting height.
￭With a higher mounting height, the range increases, but the detection sensitivity
decreases.
2
1
3
8.00
m
4.80
m
3.20
m
2.50m
Recommended mounting height: 2.5 m
1Walking across
2Walking towards
3Seated activity

Operating Manual
BL2 93317
8
4.2 Mounting options
4.2.1 Ceiling installation
4.2.2 Surface mounting with mounting set 93256
Ø 68 mm
1 2
3 4

BL2 93317
Operating Manual 9
5 6
7 8
9 10

Operating Manual
BL2 93317
10
4.2.3 Flush mounting with mounting set 93251
1 2
3 4
5 6
7 8

BL2 93317
Operating Manual 11
5 Electrical connection
DANGER
Danger of death due to electrical shock!
Work on electrical equipment may only be carried out by certified electricians or by
instructed persons under the direction and supervision of a certified electrician in accord-
ance with the electrical engineering regulations.
➜Disconnect supply before installing!
➜This device is not to be used to isolate other equipment from the mains supply.
WARNING
Observe inrush currents!
Due to the high inrush currents of electronic ballasts and LED drivers, the maximum num-
ber of switchable luminaires is limited.
➜Use an external contactor for a large number of loads.
9

Operating Manual
BL2 93317
12
5.1 Preparing the connection
5.1.1 Preparing the connection cable
5.1.2 Opening the terminal compartment.
5.1.3 Strain relief/protection against accidental contact
NOTICE
Install strain relief/protection against accidental contact!
The cover of the terminal compartment also serves as strain relief and protection against
accidental contact.
➜After the electrical connection has been made, reinstall the cover.
0.5 … 1.5 mm2
0.5 … 1.5 mm2
1
3
2
10mm
1Solid conductors
2Stranded conductors
3Stranded conductors with ferrules
1 2

BL2 93317
Operating Manual 13
5.2 Schematic wiring diagrams
5.2.1 Standard connection
5.2.2 Parallel connection
NOTICE
Parallel connection!
Up to 8 detectors can be connected in parallel to extend the detection range. .
➜For parallel connection, connect all detectors to the same phase conductor.
1
21Switch for manual switching
2RC suppressor for arc extinction
(accessory, optional)

Operating Manual
BL2 93317
14
5.3 RC suppressor unit
6 Commissioning
6.1 Factory default settings
The values printed in bold are the factory settings.
6.2 Self-test cycle
After power-on, the detector goes through a self-test cycle of 10 s. Different flashing of the LEDs
(see chapter 3.3 "LED indicators") indicates whether the detector has already been programmed or
whether the factory settings are active.
NOTICE
Interference suppression of the loads!
All switched loads must be properly suppressed.
We recommend our RC suppressor units (see accessories).
Device
Switch-on threshold
500 Lux
Adjustment range by remote control:
20 Lux - 1000 Lux
Sensitivity High
(HIGH, MEDIUM, LOW)
Status LEDs Function active
(active, inactive)
Follow-up time 3 min
(15 s – 60 min)
INFO
With a switch-on threshold greater than 1000 lux (day mode, "sun" setting), the light
evaluation is inactive, i.e. the detector operates independently of brightness.

BL2 93317
Operating Manual 15
6.3 Adjustment via IR remote control
The device can be adjusted by infrared remote control. No adjustments can be made to the device
itself.
The white LED of the detector flashes briefly fast to confirm the correct reception of an IR signal.
6.3.1 Commands
Button Command
Close detector (locked state)
When closed, only the switch illumination and RESET functions are available.
Open detector (unlocked state)
Press this key to open (unlock) the device for programming.
The settings for the day/night operation, the switch-on threshold, the follow-up time,
the detection sensitivity and the status LEDs can then be made. The procedure is ter-
minated automatically after 3 minutes of no further input or by pressing the 'Close
detector' button.
Reset to factory default settings
This command (long key press > 3 s) resets the device to its factory setting.
Store brightness
This key is used to measure the ambient brightness and apply the value as the switch-
on threshold.
Switching the illumination
The illumination is switched on or off and the follow-up time is started.
93055 – IR-
BL
CAUTION
Factory default settings!
The individually made settings are lost.

Operating Manual
BL2 93317
16
6.3.2 Parameter
Button Parameter
Day operation
The switching of the output when a movement is detected is almost light-independent
(switch-on threshold approx. 2000 lux).
Night operation
The light evaluation is performed with a minimum switch-on threshold of 10 lux.
to
Switch-on threshold
The brightness value below which the illumination is switched on is called the switch-
on threshold.
The switch-on threshold can be selected between 20 Lux and 1000 Lux. Below this
value, the illumination is switched on during movement.
to
Follow-up time
This is the duration after a movement for which the connected illumination remains
switched on.
or
o
r
Detection sensitivity
With a high detection sensitivity, even smaller movements are detected and larger
areas are detected.
Status LEDs
This button is used to activate or deactivate the status LEDs.

BL2 93317
Operating Manual 17
6.3.3 Adjusting the parameters with the remote control
Day operation (light evaluation inac-
tive) or Night operation
Open (unlock) the device – Activate
the programming mode
Select switch-on threshold or read in
current light value as new switch-on
threshold.
Follow-up time (illumination)
15 s – 60 min
Detection sensitivity Low (LOW),
Medium (MEDIUM)
or High (HIGH)
Status LEDs activated / deactivated
Close (lock) device
If no further input is made for
approx. 3 minutes, the programming
mode is automatically terminated.

Operating Manual
BL2 93317
18
7 Care, maintenance and disposal
7.1 Cleaning
If necessary, clean the plastic lens of the motion detector with a soft, lint-free cloth.
7.2 Maintenance
Usually, the motion detector does not require any maintenance by the operator. Repairs to the
device must only be carried out by the manufacturer.
For repairs, contact your local B.E.G. Brück Electronic subsidiary or directly B.E.G. Brück Electronic
GmbH, Germany.
7.3 Disposing
For disposal observe the applicable national regulations regarding electronic components.
NOTICE
Do not use aggressive cleaning agents!
➜Do not use aggressive cleaning agents such as thinner or acetone for cleaning the
device.
➜To clean the lens, use only a lint-free cloth.
Tips and hard objects can destroy the lens.