B.E.G. LUXOMAT PD4-M-1C-C-PS User manual

Installation and Operating Instruction for B.E.G. Occupancy detector PD4-M-1C-C-PS-SM/FC
LUXOMAT®PD4-M-1C-C-PS
1. Mounting preparation
Work on the 230 V mains supply may only be carried out
by qualified professionals or by instructed persons under
the direction and supervision of qualified skilled electrical
personnel in accordance with electredechnical regulations.
Disconnect supply before installing!
The device is not suited for safe disconnection of the mains
supply.
When in Master/Slave mode of operation, the Master-
appliance must always be installed at the location where
there is least daylight.
GB
A circular opening of
diameter 68 mm must
first of all be pro duced
in the ceiling.
Having connected up
the cables in accord-
ance with regulations,
the detector is inserted
into the opening as
shown in the drawing
opposite and fixed into
position with the assis-
tance of the spring clip.
4b. Installation of the LUXOMAT®PD4-M-1C-
C-PS-FC
5a. Hardware configuration SM
Position LED’s and potentiometers
LED 1 green
LED 2 red
LED 3 white
40
15
30
1
2
5
10 16
TEST
1 2 3
6a. Position DIP-switches SM
DIP 1 Fully-automatic/semi-automatic mode
DIP 2 LED ON/OFF
DIP 3 Change between corridor mode and standard
mode
The DIP-switch settings are overriden using the remote control.
Surface
mounting
OFF ON
VA
LED
HA
COR
ONOFF
DIP
Potentiometer 1 Lux
Potentiometer 2 Time
40
15
30
1
2
5
10 16
TEST
1 2 3
7. DIP-switch functions
DIP-
switch
ON OFF
1 Semi automatic mode Fully automatic mode
2 LED OFF LED ON
3 Corridor mode Standard mode
DIP
OFF ON
1
2
3
LED 1 green
LED 2 white
LED 3 red
5b. Hardware configuration FC
Position LED’s and potentiometers
1 2
12 3
Potentiometer 1 Lux
Potentiometer 2 Time
DIP 1 Fully-automatic/semi-automatic mode
DIP 2 LED ON/OFF
DIP 3 Change between corridor mode and standard
mode
The DIP-switch settings are overriden using the remote control.
6b. Position DIP-switches FC
False ceiling
mounting
ON
OFF
DIP
123
Corridor function: After deactivation by an external push
button, the detector switches off and returns to automatic
mode after 5 sec.
The DIP settings are enabled again by:
• Adjusting the DIP-switches when closed
• Reset with test sun setting at the potentiometers
• Reset when open
S L L
RRel2 N
Rel1
230 VAC ±10%
50-60 Hz
C
4a. Installation of the LUXOMAT®PD4-M-
1C-C-PS-SM
The detector must be installed on a solid and level
surface. The circular cover ring must be removed prior
to assembly. To do this, twist the lens (C) anticlockwise
through approximately 5° and lift off.
Having connected up the wires in accordance with
regulations, secure the detector with 2 screws. After
installation replace the lens and lock (turn clockwise).
Mains to be connected.
ATTENTION: For maximum
sensitivity the detector-,
lens- and corridor-axis must
match.
ATTENTION: For maximum sensitivity the detector-, lens-
and corridor-axis must match.
open
close
opened closed
For an increased operational safety the PD4-M-C-FC-SP is
fitted with two relays:
Relay 1 = operating relay with NO-contact
Relay 2 = fault relay with NC-contact
A number of basic functions are monitored in the device and
in case of a deviation a failure is shown. Blinking of all LEDs
indicates a recognized failure.
In this position the NC relay has fallen off and is responsible
for the contact between L and L’ (light on). A recognised
failure can only be reset by a network interruption!
2. Operation of the PD4-M-1C-C-SP 3. Monitored functions
Tension monitoring
Operating tension is monitored internally. If a voltage failure is
recognized, a failure is activated.
CdS-monitoring
Monitoring if the detector switches between the positions light/
dark (active/not active) within a period of 24 hours. If the
appliance did not change the position “too light” within this
period of time, the light sensor is defective (or wrong program-
ming) and a failure is activated.
Relay monitoring
When switched on, a phase monitoring of L‘ is active. If not
recognized, the relay or the contact is defective and a failure is
activated.
All manuals and user guides at all-guides.com
all-guides.com

8. Putting into operation / Settings
Self test cycle
After an initial 60-second self-test cycle, the LUXOMAT®PD4-M-1C-C-PS is
ready for operation.
Potentiometer 1 – Adjustment twilight-switch for light control
The switch-on value for the light can be set at between 10 and
2000 Lux. Using the potentiometer, the luminance set points can
be set as desired.
Symbol : Night operation
Symbol : Day/Night operation
Determining the current brightness
Set potentiometer 2 to the “Test“ setting. The green LED lights
up permanently as soon as the value set at the potentiometer
dropps below the current measured brightness.
Potentiometer 2 – Adjustment follow-up time channel 1 “Light“
Symbol TEST: Test mode, reacts on motion only. Every
movement switches on the light for a period of 2 seconds,
switching it off for a period of 2 seconds. The time can be set
infinitely variably at between 15 sec. and 30 minutes.
The potentiometer settings are overriden using the remote control.
Pulse spacing PD-Slave
2 or 9 seconds can be set for the pause between 2 pulses sent
to the Master. The setting can be made with activated
() or deactivated ( ) LED indicator.
For devices with a separate Slave input, 2 sec. can be set.
120 6050
40
30
15
10
A
16 10 5
2
1
30
15
TEST
2000
1200
600
200
40
5
120 6050
40
30
15
10
A
16 10 5
2
1
30
15
TEST
2000
1200
600
200
40
5
9s 2s
LED ON
LED OFF
10. Putting into operation of the remote
control IR-PD-1C (optional)
Check Battery:
Open battery compartment by
pressing the plastic springs together
and removing the battery-holder.
Caution: Settings with remote control supersede the
settings by potentiometers.
2 1
120 6050
40
30
15
10
A
16 10 5
2
1
30
15
TEST
2000
1200
600
200
40
5
120 6050
40
30
15
10
A
16 10 5
2
1
30
15
TEST
2000
1200
600
200
40
5
9. Reset and default settings
1. Default settings
If the potentiometers are in the
“Test“ and “Sun“ position and
the detector is unprogrammed,
the factory program is activated:
500 Lux and 10 min.
2. Reset
If both potentiometers are returned to the “Test“ and
“Sun“ setting from any other position, a reset is executed.
All values programmed with the remote control are
deleted.
11. Settings by remote control
Unlocking device – Activation of the
programming mode
Locking device – Exit programming mode
If there is not reaction for about 3 minutes the
programming mode will be deactivated.
Change between fully-automatic and semi-automatic
mode (HA) => (see page 3, point 17)
Luminance set point for channel 1
20 - 1000Lux
Automatic reading in the current light value as
new luminance set point => (see page 3, point 14)
Change between motion detector and
photo electric switch
Increase the current light level
by 20 resp. 50 Lux
Light ON/OFF
HA
ON/OFF
Resetting when
open: Deletes all
values set with
the remote con-
trol, light OFF.
Potentiometer
and DIP switches
are enabled for
setting.
or
1000
20 to
+
Follow-up time channel 1 (light)
5 - 30 min. or impuls

 

to
LED ON/OFF (by holding down the push button)
or Detection sensitivity
reduced or normal


5
min
Daytime operation, detector only activated by motion
or
PI R
CdS
Permanent protection against sabotage
White LED ashes
when choosing CdS
12. Key functions in closed state
Light ON/OFF during the detection of motion
plus follow-up time; Activation of the 12 h-ON/
OFF-function by holding down the push button
=> (see page 3, point 15)
Switches channel off and is immediately active again,
exits all timers, interruption of light measurement
Activation/Deactivation of the test function
After 3 minutes the test mode will be
automatically closed.
Changes to “open“ state
Changes to “closed“ state
Permanent protection against sabotage
This function blocks the unit permanently. This operat-
ing mode can only be activated during the period of 5
seconds (white LED flash) after pressing the “lock“ but-
ton. The procedure for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 - 59 seconds
3. Switch of the current again
4. Apply current, wait for selftest cycle
5. Open detector
max
50
Lux
1500
Lux
ON
OFF
13a. In the initialisation period
12 h Light ON/OFF (party function)
Activated by “Light“ push button
Deactivated by “Reset“ push button (default)
Corridor function (see point 15a)
Activated by “outside“ push button
Deactivate by “inside“ push button (default)
Forced shutdown (see point 15c)
Activated by “sun“ push button
Deactivate by “moon“ push button (default)
13b. In opened state
This push button opens the detector and the following
functions can then be programmed.
Attention: The detector is closed automatically:
• after every voltage recovery
• after 3 minutes
The state changes to “closed“.
In the first 5 seconds, the white LED flashes every
0.5 seconds. During this time, sabotage protection
can be activated.
The device distinguishes between 2 procedures:
• Reading in with lighting switched on:
The switch-on value is determined automatically.
Determining the switch-on value:
1. Press the “eye“ push button
2. Switch off the light (2 seconds later)
3. Read in the brightness
4. Switch-on value = Read brightness
• Reading in with lighting switched off:
When the push button is pressed, the current
brightness is specified as the switch-on value. The
switch-off value is determined automatically.
If the brightness has been modified, the switch-off
threshold is recalculated.
Each time the push button is pressed, the device
increases the current switch-on value in increments of
20 Lux for a current switch-on value of < 100Lux and
in increments of 50Lux for a current switch-on value
of > 100 Lux.
1000
Lux
20
Lux
Standard sensitivity for most applications
Reduced sensitivity for outdoor applications
When the pulse function is active, a pulse of 1sec. is generated
every 9 sec. If the pulse function is activated via remote control,
the pause between 2 pulses can be modified. After activating
the function via the “Pulse“ push button, select the desired time
within 5sec.:


5
min = 9 sec., 

10
min = 10 sec., 

15
min = 15 sec., 

30
min = 30 sec.
The “Test“ push button can be used to set the LED ON/OFF
function. To do this, hold down the push button for 3 sec.
Please note that in the open state and in test mode, the LED
indicators are always ON.
Twilight switch function (CdS)
If the CdS function is active, the detector acts as a simple twilight
switch. Only the brightness can be set in this mode. Movements
are no longer indicated by the red LED.
Push button acknowledgement:
Each push of a button is indicated by lamp acknowledgement
and by the white LED.
“Light ON“ status: OFF/ON (approx. 0.5sec. each)
“Light OFF“ status: ON/OFF (approx. 0.5sec. each)
+
PI R
CdS
13. Explanation of the remote control button functions
Option: Remote control IR-PD-1C (92520)
(Label to be used with IR-PD)
An adhesive film for the surface of the IR-PD-1C is inclu-
ded with the device. If required, this can be used for any
B.E.G. remote control with 27 keys.
LUXOMAT
®
PD3
B.E.G.
500
200
400
100 20
IR-PD-1C
PIR
CdS
ON/OFF
HA
B.E.G. LUXOMAT® B.E.G. LUXOMAT®
Wall bracket for remote control
IR-PD-1C
optionaloptionaloptionaloptional optional
t < 5 sec.
t < 5 sec.
All manuals and user guides at all-guides.com

HA
ON/OFF
18. Range of Coverage
In case the sensing area of the LUXOMAT®
PD4-M-1C-C-PS is too large or areas are being covered
that should not be monitored, the range can be reduced
or limited through use of the enclosed masking clips.
19. Exclude sources of interferences
Typ SM FC FM
PD4-M-1C-C-SP (Master) 92485 92480 –
PD4-S-C (Slave) 92442 92444 92445
LUXOMAT®Remote control:
IR-PD-1C (incl. wall bracket) 92520
IR-PD-Mini 92159
Accessory:
BSK Ball basket guard 92199
Wall bracket for remote control as
replacement
92100
22. Article / Part nr. / Accessory
20. Technical data PD4-Master-1C-C-SP
1. If the switch-on threshold has been modified by the potentiometer
or remote control, the switch-off threshold stored in the EEPROM is
deleted and is then recalculated on the next activation.
Determining the switch-off value
1. Switch on for 5min. with dark and motion
2. Light OFF for 2 sec.
3. Internal calculation of the switch-off value
2. If the eye push button is pressed, the switch-off threshold is
recalculated. See also Remote control –> Eye section
3. Switch-off delay
If the determined switch-off threshold is exceeded during
operation, the detector only switches off after a delay of approx.
15 minutes. This compensates for any brief fluctuations in the
brightness.
14. Switch-off threshold brightness
21. Wiring diagram
Standard mode with Master 1-channel occupancy
detectors-PS with R and S terminal




 



   



SM
FC
Optional
T1 = NO-button for semi-automatic mode;
Extension of the detection area with Slave-devices
10 m 20 m
2.50 m (max. 3m)
40 m
20 m
3 m
5 m
1
2
1
quer zum Melder gehen
frontal zum Melder gehen
Unterkriechschutz
walking across
walking towards
2
Sensor and power supply in one case
Power supply: 230 V~ ±10 %
Power consumption: < 1W
Ambient temperature: -25°C – +50°C
Degree of protection/class: SM IP54, FC IP20 / II /
Settings: locally and by remote control
Light values - IR-PD-1C: 20 - 1000 Lux
Extension of the detection area: with Slaves
Area of coverage: narrow detection area, ideal for
corridors
Range of coverage Ø H 2.50 m / T=18°C:
tangential 40m / radial 20 m
Mounting height: 2 - 3 m
Light measurement: daylight + artificial light
Lux values - Potentiometer: 10 - 2000 Lux
• 1 Relay/Channel for light-connection
Type of contact: NOC / with pretravel tungsten
contact
Contact load: 2300 W, cos ϕ=1 /
1150 VA, cos ϕ= 0.5, µ- Contact
Time-settings:
15 sec. - 16 min./ test with potentiometer
5 min. - 30min./ test with remote control
Dimensions H x Ø [mm] SM FC
PD4-M-1C-C-SP 76 x 101 103 x 97
Visible portion when built into ceiling: 30x97mm
Technical data PD4-Slave-C
Power supply: 230 V~ ±10 %
Impulse output: Optocoupler max. 2 W
Impulse duration: 2 sec. or 9 sec.
Dimensions: see above
Declaration of Conformity: The product complies with the low
voltage recommendation 2006/95/EC and the EMV recommen-
dation 2004/108/EC.
The “Corridor“ and “Light ON/OFF“ functions are mutually
exclusive. If both are activated, the detector performs the corridor
function.
The behaviour when the push button is pressed is defined
as follows:
Corridor function activated
Light ON:
Push button pressed briefly: Light OFF -> Active after 5sec.
Push button held down: Light OFF -> Active after 5 sec.
Light OFF:
Push button pressed briefly: Light ON as long as motion + Lag time
Push button held down: Light ON as long as motion + Lag time
15a. Behaviour of external push button/IR “Light“
12 h Light ON/OFF activated
Light ON:
Push button pressed briefly: Light OFF -> Active after 5sec.
Push button held down: 12 h OFF
Light OFF:
Push button pressed briefly: Light ON as long as motion + Lag time
Push button held down: 12 h ON
12 h Light ON/OFF deactivated
Light ON:
Push button pressed briefly: Light OFF as long as motion + Lag time
Push button held down: Light OFF as long as motion + Lag time
Light OFF:
Push button pressed briefly: Light ON as long as motion + Lag time
Push button held down: Light ON as long as motion + Lag time
15b. Behaviour of external push button/IR “Light“
Activation of light for 12 h via mains interruption
1. Interrupt current
2. Apply current for 2 to 5 sec.
3. Interrupt current again
4. Apply current
5. Detector is now ON for 12 h
Exiting sabotage
1. Interrupt current
2. Apply current for 30 to 60 sec.
3. Interrupt current again
4. Apply current
5. Detector is in simple closed state
230 V AC permanently at the slave input
If 230 V AC is applied at the slave input for longer than 10sec.,
the light is switched on permanently. When the 230V is removed,
the light is switched off and automatic mode is activated.
230 V AC for 1 - 3 sec. at push button connection S
If 230 V AC is applied for 1 - 3 sec. at push button connection
S, this is interpreted as a Slave signal at slave connection R. This
ensures that the detector is compatible with previous versions.
16. Other functions
Forced shutdown active
Light OFF:
Light OFF: Push button pressed briefly: Light ON for approx.
30min., then forced shutdown if the set brightness is still exceeded.
15c. Behaviour of external push button/IR
“Forced shutdown”
17. Fully-automatic and semi-automatic mode
(see functions IR-PD-1C)
Fully-automatic operation
In this operating mode, the lighting switches automatically
on and off for increased comfort, depending on presence
and brightness.
- Channel 1 switches on in the event of motion if “dark“ is
detected.
Semi-automatic operation
In this operating condition, in order to gain increased
savings, the lighting is energized only after being manually
switched on.
Switch-off takes place automatically or manually.
The semi-automatic mode basically behaves like the fully-
automatic one. However, the difference is that switching-on
must always be carried out manually!
As many (closer-contact) buttons as desired can be wired in
parallel on the “S” button input (ON/OFF).
Triggering in semi-automatic mode: If the detector switches
off in semi-automatic mode (lag timer elapsed), the detector
is switched on again within 10 sec. by motion (despite semi-
automatic mode).
All manuals and user guides at all-guides.com

N L–L L΄–L' S
N R
23a. PD4-M-1C-C-PS-SM – Connection
23b. PD4-M-1C-C-PS-FC – Connection
24. LED function displays
LED function indicators after each mains recovery (60 sec. initialisation period)
Operating state LED function indicators
Factory pro-
gram active
White, red and green flash in quick succession for 10 sec., then initialisation indicators,
see below
Double-locked white and green shines for 5sec. all 20sec., afterwards initialising notification
Indicator
unprogrammed
Indicator
programmed
Indicator also when forced shutdown
is activated
Standard mode Red flashes Red flashes quickly Every 5 sec., 4 x white, red and
green in quick succession
12 h ON/OFF
active
Red and green
flash
Red and green flash
quickly
Every 5 sec., 4 x white, red and
green in quick succession
Corridor active Red and white
flash
Red and white flash
quickly
Every 5 sec., 4 x white, red and
green in quick succession
12 h ON/OFF
& corridor active
Red, green and
white flash
Red, green and white
flash quickly
Every 5 sec., 4 x white, red and
green in quick succession
CdS active – Red and white flash Then no red LED for motion detection
LED function indicators during operation
Process LED function indicators
Motion detection Red flashes on each detected movement
Semi-automatic mode active White is ON
Impulse active Red and green flash one time all 4 sec.
Corridor active White ON 1sec. and OFF 4sec.
Corridor and semi-automatic
mode active White ON 4sec. and OFF 1sec.
Too bright detected Green flashes
Light measurement active Green flashes once every 10 sec.
12 h ON/OFF function active Red and green flash alternately
Duration ON active (by slave) Red flashes quickly
IR command White flashes once
IR command “open” and
sabotage active White and green flash once slowly
Failure all LED´s flash quickly
Wiring Diagram
PD4-M-1C-C-PS-SM
Wiring Diagram
PD4-M-1C-C-PS-FC
L–L L'–L' N–N S R
L
N
L
N
R
R
Slave
Slave
T1
T1
E1
E1
MAN 7247 – 140212–1
All manuals and user guides at all-guides.com