B.E.G. LUXOMAT PD2-M-1C User guide

1
1 2
2
120 6050
40
30
15
10
A
16 10 5
2
1
30
15
TEST
2000
1200
600
200
40
5
2000
1200
600
200
40
B.I.T.
Q.C.
PASSED
1
2000
1200
600
200
40
120 6050
40
30
15
10
A
16 10 5
2
1
30
15
TEST
2000
1200
600
200
40
5
120 6050
40
30
15
10
A
16 10 5
2
1
30
15
TEST
2000
1200
600
200
40
5
IR-PD
IR-PD-Mini
3. Putting into operation / Settings
Follow-up time for light control
The time can be set infinitely variably at between
15 seconds and 16 minutes.
Symbol
: impulse < 1sec.
Symbol TEST: Test mode
(Every movement switches on the light for a period of 1
second, switching it off for a period of 2 seconds after that
regardless of the level of brightness.)
Twilight-switch for light control (relay 1)
The switch-on value for the light can be set at between 10
and 2000 Lux. Using the rotary control, the luminance set
points can be set as desired.
Symbol : Night-time operation
Symbol : Daytime/Night-time operation
Installation and Operating Instruction for B.E.G. - Occupancy detectors PD2-M-1C-SM/-FC/-FM
The detector can be installed
in conventional inlet-sockets
mounted on the ceiling.
The assembly plate enclosed
must be stripped off prior to
installation and secured to the
ceiling using 4 screws and
ensuring that it is not laterally
transposed.
Having connected up the
cables in accordance with
regulations, the detector can
be placed in position as shown
in the drawing opposite and,
applying a little pressure, can
then be locked into position with the assistance of
the spring clips.
2a. Installation of the LUXOMAT
®
PD2-M-1C-SM
2c. Installation of the LUXOMAT®
PD2-M-1C-FM
The detector must be in-
stalled on a solid and level
surface. There is no need
for frames.
For mounting remove lens
(C) (turn anticlockwise).
Fasten the mounting pod
to the ceiling.
Having connected up the wires in accordance
with regulations, secure the detector with 2
screws as per the illustration above. In order
to assemble the detector outside, the PD2-IP54
base-plate, which is available as an accessory,
must be mounted between the detector and the
surface on which it is to be installed.
Unlocking device
Lock device
4. Settings carried out using remote control (optional)
Remote control LUXOMAT IR-PD
1. Check Battery:
open battery compartment by pressing the
plastic springs together and removing the
battery-holder.
2. IMPORTANT
Please pay attention, that the setting is Potentio-
meter 1 at “TEST” and Potentiometer 2 not at
“SUN”. All values which have been programmed
using the remote control will be deleted in the
event of power failure in the position “TEST/
SUN”. Please switch Potentiometer 2 over to
“MOON” or any other value.
Caution:
Settings with remote control supersede the
settings by courtesy of potentiometers.
LUXOMAT®PD2-M-1C
1. Mounting preparations
Work on the 230 V mains supply
may only be carried out by qualified
professionals or by instructed persons
under the direction and supervision
of qualified skilled electrical person-
nel in accordance with electrotechni-
cal regulations.
Disconnect supply before installing!
When in Master/Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
Lock device
Test mode
Reset to deactivate
Resetting when closed
The lighting relay is switched off, i.e.
opened and the follow-up times reset.
Permanent protection against sabotage
This function blocks the unit permanently (green LED is illuminated).
Th is operating mode can only be activated during the period of 5
seconds after pressing the “lock“ button. This status will only
permit actuating the function “Light on/Light off”.
The procedure for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 – 59 seconds
3. Switch of the current again
4. Apply current
5. Open detector
Light on/off
The light will remain switched on/off for as long as movements
are detected in the areas of coverage. Once the last movement
has been detected, the light will remain on for the duration of the
follow-up time as per setting.
The appliance will then return independently to the mode selected
(Fully or Semi-automatic).
2b. Installation of the LUXOMAT
®
PD2-M-1C-FC
The detector has
been designed
and developed
specifically for instal-
lation in suspended
ceilings.
A circular opening of
diameter 68 – 70 mm
must be produced in
the ceiling.
Having connecte d up the cables in accor-
dance with regulations, the detector is
inserted into the opening as shown in the
drawing opposite and fixed into position with
the assistance of the spring clips.
Option:
Wall bracket for remote
control IR-PD
2d. Self test cycle
The product enters an initial 60-sec-
ond self-test cycle, when the supply
is first connected. The occupancy
detector is ready for operation.


max
50
Lux
1500
Lux
ON
OFF
max
50
Lux
1500
Lux
ON
OFF



 

max
50
Lux
1500
Lux
ON
OFF
Luminance set point
Automatic reading in the current light value
as new luminance set point
Individual light value 2 - 2500 Lux
Follow-up time (relay and channel 1)
15 sec. up to 30min.
Impulse function (relay and channel 1)
1sec. ON, 9 sec. OFF
Preset/user mode
Fully automatic/semi automatic mode => (see page 2, point 5)
Semi automatic: red LED (ashing),
Fully automatic: red LED on for approx. 3sec.
Resetting when open
All values which have been programmed using the remote
control IR-PD are deleted, and those values which have
been set by potentiometer are activated.
120 6050
40
30
15
10
A
16 10 5
2
1
30
15
TEST
2000
1200
600
200
40
5
120 6050
40
30
15
10
A
16 10 5
2
1
30
15
TEST
2000
1200
600
200
40
5
GB

1
2
e
max
50
Lux
1500
Lux
ON
OFF
max
50
Lux
1500
Lux
ON
OFF
Sensor and power supply in one case
Power supply: 230 V~ +6 %/-10 %
Power consumption: < 1W
Ambient temperature: -25°C to +50°C
Degree of protection/class: SM IP54, FC and FM IP20 / II
Settings: locally and by remote control
Light values - IR-PD: 10 - 2000 Lux
Extension of the detection area: with Slaves
Area of coverage: circular 360°
Range of coverage Ø H 2.50m / T=18°C:
seated 2.50m / tangential 10 m / radial 6m
Recommended height for mounting: 2 - 3 m
Light measurement: mixed light, daylight + artificial light
Lux values - Potentiometer: 10 - 2000 Lux
• Relay/Channel 1 for light-connection
Type of contact : NOC/with pretravel tungsten contact
Contact load: 2300 W, 230 V~, 10 A cos (ϕ) =1 /
1150 VA cos (ϕ) = 0.5
DIM-Output: 1 x (1-10 V)
Max. no. of series-connected electronic ballasts:
max. 50 electronic ballasts by one single supply with
max. 100 m cable run and a conductur cross-section of
0.75 mm²
Time-settings: 15 sec. - 16 min. (30 min. with remote
control) / test
Dimensions HxØ [mm] SM FC FM
PD2-M-1C 50 x 98 84,5 x 80 65 x 98
Visible portion when built into ceiling: 34 x 79 mm
Technical data PD2-Slave
Electrical data same as above, but just one channel for
signaling motion detection.
Declaration of Conformity: The product complies with
the low voltage recommendation 2006/95/EC and the
EMV recommendation 2004/108/EC
12. Technical data PD2-Master-1C
10. Wiring diagrams
Type SM FC FM
PD2-M-1C 92550 92565 92555
LUXOMAT®Remote control:
IR-PD (incl. wall bracket) 92160
IR-PD-Mini 92159
Accessory:
BSK Ball basket guard 92199
Wall bracket for remote control as replacement 92100
Socket IP54 92161
9. Article / Part nr. / Accessory
MAN 5628 – 141209-4
In case the sensing area of the LUXOMAT®PD2-M-
1C-SM is too large or areas are being covered that
should not be monitored, the range can be reduced
or limited through use of the enclosed masking
clips (e).
8. Exclude sources of interference (PD2-M-1C-SM)
5. Fully / Semi automatic mode
(for IR-PD functions see page 1)
Fully automatic operation
In this operating mode, the lighting switches automati-
cally on and off for increased comfort, depending on
presence and brightness.
Semiautomatic operation
(Semiautomatic can only be activated via the remote
control!)
In this operating condition, in order to gain increased
savings, the lighting is energized only after being manu-
ally switched on.
Switch-off takes place automatically.
The semiautomatic mode basically behaves like the fully
automatic one. However, the difference is that switching-
on must always be carried out manually!
As many (closer-contact) buttons as desired can be wired
in parallel on the “S” button input (ON/OFF).
13. LED-functional indicators, fault-finding
The functional indicators in the case of the LUXOMAT®
PD2-M-1C-MASTER (red and green LED‘s)
Red LED indicating self-checking mode (over a period
of 60 seconds following mains‘-supply lock-on)
Flashing at intervals of 1 second
EEPROM/memory empty
Flashing rapidly
EEPROM/memory contains information
Red LED as an indicator of status
Flashing irregularly
Movements are detected within the area of coverage
Flashing regularly
Detector identifies bright, light off
(dependent upon operating mode)
Not illuminated
Detector identifies dark, light on
(dependent upon operating mode)
Flashing extremely rapidly
Too bright / Too dark / Undefined
Red LED as an acknowledgement of receipt for
commands from the remote control
Illuminated for 2 seconds
Signal validly received
Illuminated for 0.5 seconds
Not-accepted command, detector blocked
Flashing extremely rapidly
Not-accepted command, occurs, for example, when
an attempt is made to input twilight-value are too
bright or too dark
Lights up for 3 seconds
Fully automatic mode
Flashing for 3 seconds
Semi automatic mode
Green LED as an indicator of status (only for status
“Permanent protection against sabotage”)
Flashing irregularly
Movement are detected within the area of coverage
Flashing regularly
Detector identifies bright, light off
(dependent upon operating mode)
Not illuminated
Detector identifies dark, light on
(dependent upon operating mode)
lluminated for 2 seconds
Signal validly received
(dependent upon operating mode)
7. Range of Coverage
6. Manual Switching
You can switch the lighting on and off manually by
pressing the pushbutton for a short time. It will stay on or
off as long as people are detected plus the congured
follow up time.
max
50
Lux
1500
Lux
ON
OFF
11. PD2-M-1C - Connections
Connection PD2-M-1C-SM
Connection PD2-M-1C-FC/-FM
NONO
NR L L
SLAVE
S
3A
NO NO
N RL LS
SLAVE
3A
N
quer zum Melder gehen
frontal zum Melder gehen
Unterkriechschutz
walking across
walking towards
seated
Master
Standard operation
Terminal connection for standard operation
S
Master
Standard operation
Terminal connection for standard operation
SNO NO
FC
L
N
N N L L R R
Master Slave
Master-/Slave -operation with one Master and
several Slaves.
The Master is the only unit to read in the Lux levels and to
switch the connected loads. The Slave units will react on
motion only, independently of the Lux levels, by sending an
impulse via the dry contact, to the Master.
Terminal connection for Master-/Slave-operation
S
Master
Standard operation, manual switching possible (NO-
contact to be pressed for approx. 1sec.) The potentiometers
not to be set on “Test“ or “Sun“ otherwise the preadjusted
values will get lost during this manual operation.
Standard operation with external push button
S
SM
SM
10 m
6 m
2.50 m
10 m
360°
2.50 m
1
2