B-K lighting Yukon Bollard User manual

TOOLS
NEEDED:
3/32”, 1/8” & 7/64” Allen Wrench
Waterproof Wire Connectors
Sleeve or Wedge Anchors for Concrete (1/4” Dia. Min.)
7/16” Socket
Yukon Bollard
Warning High Voltage
Installation Instructions
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all
Local and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping
of this product.
• Before wiring to power supply and during servicing or
relamping, turn off power at fuse or circuit breaker before
service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause
an unsafe condition. The use of damaged components may
cause an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or
part, as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time.
Use a clean, dry, soft cloth to handle the lamp. Oil from
skin may damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept
clean during installation and service; failure to do this may
cause an unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT
SAFETY INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
CONCRETE INSTALLATION ONLY
RELEASED DATE
09/03/2021
REFERENCE NUMBER
INS-2850-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
RE2/RE2: Dual - GFCI w/USB
RE1/RE1: Dual - GFCI
Avaiable Configuration:
Machined
Aluminum
Housing
RE1/RE2: Dual - GFCI & GFCI w/ USB
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/collaterals/install/digit.
pdf for more information.

Finished Grade
3. Install anchor plate and bolt assembly flush
with the finished grade.
1 1/2”
1. Adjusted anchor bolts to project at least 1-1/2”
using the four (4) 1/4-20 nuts to the top of the
plate. The four (4) nuts can be left in place
while concrete is poured.
4. With the conduits in place and the anchor
plate properly positioned, secured and leveled,
concrete may be poured.
2. Run conduit inside of the anchor plate center
hole prior to pouring concrete.
YKB Anchor Kit Installation
5. The fixture may be installed by removing the
four (4) 1/4-20 nuts and re-using them to
secure the fixture mounting base assembly.
Trim conduit as needed.
Soil Prep
Conduit
trench
B. Dig hole 13” wide and 24” deep.
Conduit
Trench
Excavate for
anchor bolts
C. Prep soil according to DIG-IT Guide.A. Determine Soil Type by referencing DIG-IT
Guide. Prep soil according to DIG-IT Guide.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
RELEASED DATE
09/03/2021
REFERENCE NUMBER
INS-2850-00
Yukon Bollard
Installation Instructions

1. Remove 1/4-20 nuts from installed YKB
anchor kit with a socket. Keep the hardware
to reuse in the next step.
2. Line up then place base over installed 1/4-
20 nuts.
3. Secure to anchor bolts with the 1/4-20 nuts
and lockwashers provided with the YKB
Anchor kit using a socket.
Base & Tenon Installation
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
RELEASED DATE
09/03/2021
REFERENCE NUMBER
INS-2850-00
4. Seal as per NEC with waterproof silicone
sealant (not included).
Yukon Bollard
Installation Instructions
If the fixture has a receptacle.
7. Secure receptacle cover by tightening #6-32 set
screw using a 7/64” allen wrench.
6. Attach receptacle to installed anchor base
with (4) #10-32 stainless steel countersunk
screws at the base using a 1/8” allen wrench.
5. Pull primary branch circuit wiring and any
additional dimming controls or other wiring
necessary for installation (not included).
Attach ground from branch circuit to ground
lead on the anchor base. Place connectors
inside of the housing. (Please refer to page
4 for wiring diagram.)

40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
RELEASED DATE
09/03/2021
REFERENCE NUMBER
INS-2850-00
LINE
COM
GROUND GROUND
RECEPTACLE
LINE
COM
GROUND
- DIM
+ DIM
GROUND
FIXTURE
LINE
COM
GROUND GROUND
FIXTURE
WIRING DIAGRAM
Pull branch circuit wiring. Make watertight
connections from primary branch circuit to pre-
wired 12ga solid wire receptacle leads using
waterproof wire connectors (not included).
Connect incoming ground and ground from
receptacle to ground wire on base. See wiring
diagram.
WIRING DIAGRAM - 0-10
Pull branch circuit wiring. Make watertight
connections from primary branch circuit to
pre-wired 16/5 round jacketed fixture head
leads using waterproof wire connectors
(not included). Connect incoming ground
and ground from receptacle to ground wire
on base. See wiring diagram.
WIRING DIAGRAM - INC
Pull branch circuit wiring. Make watertight
connections from primary branch circuit to pre-
wired 16/3 round jacketed fixture head leads
using waterproof wire connectors (not included).
Connect incoming ground and ground from
receptacle to ground wire on base. See wiring
diagram.
RECEPTACLE INSTALLATION DIAGRAM
FIXTURE INSTALLATION DIAGRAM
Yukon Bollard
Installation Instructions
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS