B-K lighting Well Star WS Series User manual

WELL STAR™
Installation Instructions
2. Supply low voltage wiring necessary for
installation (By Others)
NOTE: Leave sufficient wire length in the
fixture housing for future service.
SUBMITTAL DATE
9-29-11
REFERENCE NUMBER
INS000968
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
TOOLS
NEEDED:
By Others
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or
relamping, turn off power at fuse or circuit breaker before
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens. Lens
must be cleaned on regular basis.
• Lighted lamp gets hot very quickly. Allow it to cool before
replacing lamp.
• Entire fixture may become extremely hot. Do not touch hot lens
or fixture body. Do not touch the lamp at any time. Use a clean,
dry, soft cloth to handle the lamp. Oil from skin may damage the
lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
3/32” allen wrench
Wire connectors
(recommended silicone filled wire connectors)
Please refer to the low voltage design guide at www.bklighting.com/lvguide before installation for proper wire selection.
Finished grade
12”
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
1. Excavate trench according to designed lighting
plan 20” deep and 10” wide suitable for the 1.
Excavate trench according to designed lighting
plan 20” deep and 10” wide suitable for the 13”
fixture housing.
3. Make two water tight, low voltage connections
using proper wire connectors (By Others).
Finished grade
This set of instructions
works for:
WS - Well Star™
WS
Cast Iron Faceplate
Steel Housing
5’ of 18 gauge wire
Warning Hot
TECHNOLOGY
with

4. Insert fixture housing and low voltage wire into
trench.
SUBMITTAL DATE
9-29-11
REFERENCE NUMBER
INS000968
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
PROJECT:
TYPE:
5. Back fill with pea gravel or sand to allow sufficient
drainage. Install housing flush at grade.
Finished grade
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
ETL LISTED
CONFORMS TO ANSI/UL
STANDARD 1838 AND UL SUBJECT 8750
CERTIFIED TO CAN/CSA
STANDARD C22.2 NO. 9
Pea gravel or sand
Finished grade
Dirt or soil
WELL STAR™
Installation Instructions
TECHNOLOGY
with
To Change Lumen Output (when required).
1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.
3. Place cap on fixture and tighten set screw.
2. With flat head screw driver rotate dial to
desired lumen output.
This product is available with Adjust-e-Lume™ (Patent Pend.) for DynamicLLumen Output Control