B-K lighting GARDEN STAR GR-K User manual

REFERENCE NUMBER
INS-2841-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
GR-E
GR-K
TOOLS
NEEDED:
By Others
5/64” Allen Wrench
Waterproof Wire Connectors
Mounting Hardware
Mallet or Sledge Hammer
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all
Local and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping
of this product.
• Before wiring to power supply and during servicing or
relamping, turn off power at fuse or circuit breaker before
service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause
an unsafe condition. The use of damaged components may
cause an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin
may damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept
clean during installation and service; failure to do this may
cause an unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when turning
on.
Do not touch hot lens, guard, or enclosure
(see diagram/picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth.
Oil from skin may damage lamp.
Do not operate the luminaire fitting with a missing or damaged
shield.
SAVE THESE INSTRUCTIONS
Suitable for wet locations · Suitable for mounting within 4 ft. of the ground.
IMPORTANT LISTINGS AND CERTIFICATIONS
Warning Flammable Hot Surface
RELEASE DATE
07-27-2020
Low Voltage
Installation Instructions
GARDEN STAR™ (GR)
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS

RELEASE DATE
01/18/2021
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING REFERENCE NUMBER
INS-2841-00
2. Use a 5/16” allen wrench to loosen three
(3) #8-32 stainless steel set screws (do not
remove set screws from fixture). Remove
anchor base from the fixture.
Finished Grade
1. Drive the stake into the ground with a mallet or
a small sledge hammer (by others). Make sure
the top is flush with the finished grade.
Remote Installation
3. Attach the anchor base to the threads on the
stake. Make sure the stake is secured in the
ground.
6. Make watertight connections from remote
transformer to fixture leads using waterproof
wire connectors (by others). See wiring
diagram.
Finished Grade
4. Pull low voltage, typically direct burial cable
throught the stake center where the hole is
located to make the connect with the fixture.
Ground wire connections is based off of
local code requirements.
7. Install fixture onto anchor base. Do not pinch
wiring. Secure fixture by tightening three (3)
stainless steel set screws on fixture knuckle
using a 5/64” allen wrench. Do not overtighten
set screws.
Remote
Transformer
Low Voltage
Installation Instructions
GARDEN STAR (GR)
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION
INSTRUCTIONS
LINE 12V
Fixture
COM
Remote
Transformer
COM
WIRING DIAGRAM
For use with 12VAC remote transformer.