BALDR B0341WST2H2-V3 User manual

USER MANUAL MODEL:B0341WST2H2-V3
WIRELESS WEATHER STATION
(Please Keep the Manual for Maintenance)
Email：[e-mail]
Phone：[phone]
Thank you for choosing BALDR wireless weather station,
any help needed, please feel free to contact us :
WEB：www.baldr.com
English
Deutsche
Français
Italiano
Español
1-19
20-38
39-56
57-74
75-93

11
Contents
1.PRODUCT OVERVIEW 2
2
3
6
7
7
7
11
13
11
11
13
14
15
16
16
18
18
1.1 Package List
1.2 Product Appearance
1.3 Button Function
2.QUICK SETUP
2.1 Before Start
2.2 Initial Setting
3.MULTIFUNCTIONAL WEATHER STATION
3.4 Channel Modes
3.3 Weather Forecast
3.2 Temperature & Humidity Display
3.1 The Working Principle of Weather Station and Sensor
3.5 Alarm Setting
3.6 Backlight
3.7 Low Battery Indication
4.TROUBLESHOOTING
5.PRECAUTIONS
6.WARRANTY
7.FCC STATEMENT 19

1.1 Package List
ITEM NO. ITEM NAME FIGURE QTY
11
2
3
Main Unit
Outdoor Sensor
User Manual
1
1
1.PRODUCT OVERVIEW
2

1.2 Product Appearance
Part 1- Weather Station Main Unit Display Screen
3
(1) Calendar 7th & 8th page
(2) Time or Alarm Time 7th &14th page
(3) Weather Forecast 13th page
(4) Outdoor Sensor Channel 11th &13th page
(5) Outdoor Temperature 12th page
(6) Outdoor Humidity 12th page
(7) Indoor Temperature 12th page
(8) Indoor Humidity 12th page
(9) Max/Min Records of Temperature and Humidity 12th page
(10) Low Battery Indicator 16th page
(11) Temperature Trend Arrows 12th page
(12) Week Language Abbreviation 8th page
1
12
3
5
7
2
4
10
11
6
9
8

(1) " " Button 6th & 15th page
(2) "ALARM" Button 6th &14th page
(3) "MEM /▼" Button 6th & 12th page
(4) "CH/▲ "Button 6th &13th page
(5) "SET/C/F "Button 6th &11th page
(6) Hanging Hole
(7) Battery Compartment
(8) Stand Bracket
Temperature & Humidity Accuracy:
Temperature: 0℃~50℃/32℉~122℉, accuracy:±1 ℃/1.8℉.
Others Ranges, accuracy:±2℃/3.6℉.
Humidity:40-80%, accuracy:±5%.
Others Ranges, accuracy:±8%.
Part 2- Weather Station Main Unit Back
4
1
7
2 3 6 4 5
8

(1) Signal Light 7th page
(2) Hanging Hole
(3) Battery Compartment
(4) Channel 1-2-3 Switch
Part 3- Wireless Outdoor Sensor
To get accurate readings, please keep the main unit away
from any unusual source of heat or cold and make sure that
the outdoor sensor is also protected from direct sunlight, rain,
or the heat it may experience from being mounted on a warm
wall, or be closed near to a warm wall.
2
3
4
1
5

1.3 Button &Function
Notes: Press the “ ” button at any time to save and exit.
Function
Normal
Mode
Press
Check Alarm
Time,
Open/Close
Alarm
Set Alarm
Time
Check
MAX/MIN
Records
Clear
MAX/MIN
Records
Select
Channel
CH1/CH2/CH3,
Adjust Channel
Modes
Channel
Searching
Set Time/
Calendar/
Week
Language/
Beep
Select°C/℉Backlight
for 20s
/
Hold
Press
Hold
Button ALARM MEM /▼ CH/▲ SET/C/F
Time
Setting
Alarm
Goes Off
Turn Off
Alarm
Turn Off
Alarm
Turn Off
Alarm
Turn Off
Alarm
Enter
Snooze
Mode
Press
Decrease 1 Increase 1
Decrease
Continuously
Increase
Continuously
Confirm and
Go to Next
Step
Exit and
Back to
Normal
Mode
/
/ /
/
/
Alarm
Setting
Confirm and
Go to
Next Step
Decrease 1 Increase 1
Decrease
Continuously
Increase
Continuously
Exit and
Back to
Normal
Mode
// /
Press
Hold
6

(1) 2*AAA and 2*AA batteries should be prepared.
(2) Use new and high quality alkaline batteries.
(3) Never mix the old and new batteries.
(4) Heavy duty or low quality recharge batteries are not recommended.
(1) Open the cover of the sensor. Set up the sensor channel to CH1.
(2) Open the cover of the main unit. Inset 2 new “AAA” standard alkaline
batteries into the main unit. All icons on the screen of the main unit will light
up for 2-3 seconds, you will hear a beep, and the main unit will start to detect
the indoor temperature and humidity.
(3) Press the “CH/▲” button to set the main unit channel to CH1, matching
the remote sensor’s.
(4) Inset 2 new “AA” standard alkaline batteries into the sensor in 3 min.
The signal flashing indicates that main unit is receiving the outdoor
temperature and humidity from sensor. The receiving status will last for max
3 minutes. The signal will stop flashing after received or 3 minutes later.
(5) Please allowed the main unit and outdoor sensor at the same position for
half an hour or more after powering on.
(1) 12H or 24H Format: Press and hold the "Set/C/F" button for 3-4 secs to
start setting, the 12 or 24 Hour Format display begins to flash.
2.1 Before Start
2.2 Initial Setting
Step 1: Get the Indoor and Outdoor Humidity & Temperature.
Step 2: Set Time/Calendar/Week Language/Key Tone in order :
12H/24H > Hour > Minute > Year > MD/DM > Month > Date >
Week Language > Key Tone OFF/ON > Exit
2.QUICK SETUP
7

Press “ CH/▲” or “MEM/▼” button to select the 12 or 24 hour mode. Press
"Set/C/F" button to confirm.
(2) Hour: The “Hour” symbol begins to flash. Press “ CH/▲” or “MEM/▼”
button to adjust the value. Press "Set/C/F" button to confirm.
(3) Minute: The “Minute” symbol begins to flash. Press “ CH/▲” or “MEM/▼”
button to adjust the value. Press "Set/C/F" button to confirm.
(4) Year: The “2020 Year” symbol begins to flash. Press “ CH/▲” or “MEM/▼”
button to adjust the value. Press "Set/C/F" button to confirm. Please note that
the default year is 2020, if the weekday display is incorrect, please confirm
year was set correctly.
(5) MD/DM Format: The “M& D” symbol will flash. (M: Month, D: Date). Press
“ CH/▲” or “MEM/▼” button to to select M/D or D/M format. Press "Set/C/F"
button to confirm.
(6) Month: The “Month” symbol will flash. Press “ CH/▲” or “MEM/▼” button
to adjust the value. Press "Set/C/F" button to confirm.
(7) Date: The “Date” symbol will flash. Press “ CH/▲” or “MEM/▼” button to
adjust the value. Press "Set/C/F" button to confirm.
(8) Week Language Abbreviation: The “Week Language Abbreviation ”
symbol will flash. Press “ CH/▲” or “MEM/▼” button to select suitable
abbreviation. (Please check as below.) Press "Set/C/F" button to confirm.
8
Language German English Italian French Dutch Spanish Danish
GE EN IT FR
MO MO LU LU
DI TU MA MA
MI WE ME ME
DO TH GI JE
FR FR VE VE
SA SA SA SA
SO SU DO DI
DU
MA
DI
WO
DO
VR
ZA
ZO
SP
LU
MA
MI
JU
VI
SA
DO
DA
MA
TI
ON
TO
FR
LO
SO
Abbreviation
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday

(9) Key Tone: The “ON ” display will flash. Default setting is ON. Press the
“ CH/▲” or “MEM/▼” button to turn ON or OFF. Press the "Set/C/F" button
to confirm. After all above steps are finished, the device will automatically
exit.
(Note: The device will automatically save and exit after 20 seconds
without any operation.)
Tip: For example, I accidentally set up the wrong "Year" data. What can I do?
Please continue to finish the all time setting.
Then press and hold the "Set/C/F" button for 3-4 secs to start setting and
Press continuously the "Set/C/F" button to confirm until enter the " Year"
setting and set the correct year. （Please refer to “Year Setting”）
The data of weather forecast and outdoor humidity & temperature come from
outdoor sensors. Make sure the outdoor sensor place in proper place.
Take an example.
If place the sensor there,
the temperature goes up,
the humidity goes down.
If place the sensor here,
the temperature goes down,
the humidity goes up.
Step3: How to Mount the Outdoor Sensor and Get More Accurate
Value？
9

(1) This is forbidden, if the outdoor sensor is directly exposed to rain, facing
direct sunlight and close to any heat source.
(2) Keep well-ventilated and leave a certain space of gap between the sensor
and the wall to avoid blocking the vent of the sensor.
(3) Place the sensor at a height about 1.2-2.5 meters/3.93-8.20 feet vertically.
(4) You are near the sensor to connect the main unit. Avoid thick walls
between the units or or strong interference source using same signal
frequency(433Ghz). (such as TVs, microwaves, computers, etc).
(5) If the main unit disconnects most likely the sensor is too far from the main
unit. Please place it nearer to the sensor. Transmission Range: 100m/330ft
Open Air. (The sensor is the unit that connects to the main unit and transfer
the signal to the main unit.)
≥3.93ft
10

After the two devices are powered on, the sensor will connect to the main
unit and transfer the signal to the main unit.
The receiving status will last for max 3 minutes. The receiving signal will
flash. If no signal is received within 3 minutes, the signal will disappear and
stop receiving outdoor signals.
The transmission time of the sensor by CH1--57S, CH2 --67S, and CH3--79S.
The reception time of the main unit by CH1--114S, CH2--134S, CH3--158S.
Transmission range: 100m/330ft in the open air, RF 433Ghz.
To ensure the successful reception of outdoor temperature and humidity,
please refer to the setting steps on page 7.
3.2.1 ℃/℉Temperature Display
Press the “SET/C/F”button to select ℃or ℉unit.
(6) Vertically placement is required:
Please search "BALDR" on Youtube to Find the English Setting Video.
3.1 The Working Principle of Weather Station and Sensor
3.2 Temperature & Humidity Display
3.MULTIFUNCTIONAL WEATHER STATION
Lift with a rope
Place on a
stable surface
hang from the back
hole using a nail
11

(1) Check: Press “MEM /▼” button to switch MAX or MIN readings. The
readings will shows for 5 seconds and then will turn back to normal mode.
(2) Manually Clear: Press “MEM /▼” button to enter “MAX/MIN” Record
Mode. Then press and hold “MEM /▼” button for 3-4 seconds to clear all
the Max/Min data.The screen in indoor and outdoor temperature &
humidity will show “--”.
(3) Automatically Clear: The records will be cleared at 00:00 automatically
daily.
Arrow indications for temperature changes:
will display when the temperature changes less than 1℃/1.8℉within
one hour or compared with the last reading.
will display when the reading increase by 1℃/1.8℉within one hour
or compared with the last reading.
will display when the reading decrease by 1℃/1.8℉within one hour
or compared with the last reading.
Indoor temperature range: -10℃-50℃(14℉-122℉).
Outdoor temperature range：-20℃-60℃(-4℉-149℉).
Indoor and outdoor humidity range:1%-99%RH.
Note: If the temperature and humidity readings are below the above range,
the “LL.L”or “LL” will be displayed.
If the temperature and humidity readings are above the above range,
the “HH.H” or “HH” will be displayed.
3.2.3 MAX/MIN Record of IN/OUT Temperature & Humidity
3.2.4 Temperature Trend
3.2.2 Temperature& Humidity Range
12

The weather icon, where data hourly calculated from indoor/outdoor
temperature and humidity forecasts the weather in the next 12 hours.
IT IS NOT THE CURRENT WEATHER. The accuracy will be 70%-75% .
Please note that this forecast can’t compare with professional weather
services supported by satellites and high-performance computers. It merely
provides an approximate indication of current developments. Please give
priority to the weather forecast of the local weather forecast service.
Single Channel Mode
starts with the CH1, CH2 or CH3 Individually showing.
Single Channel Mode fit for only one sensor’s kit which will show only 1
group data of outdoor temperature & humidity in fixed channel.
Weather Icons
3.3 Weather Forecast
3.4 Channel Modes
3.4.1 Single Channel Model
Please make sure the main unit and outdoor sensor are in the same
channel .
Note: “Partly Cloudy” is default after power-on.
Circular Channels Mode starts with the the symbol of .
Circular Channels Mode fit for the kit which have 2-3 sensors
(up to 3 sensors). And the data of outdoor temperature & humidity will be
showed in order every 10 seconds.
3.4.2 Circular Channels Mode
Cloudy Rainy SnowySunny Partly Cloudy
13

(1) When main unit’s channel is CH1, press the “CH/▲” button 3 times to
switch into Circular Channels Mode.
(2) When main unit’s channel is CH2, press the “CH/▲” button 2 times to
switch into Circular Channels Mode.
(3) When main unit’s channel is CH3, press the “CH/▲” button 1 time to
switch into Circular Channels Mode.
(4) When the symbol of display in screen, it means successfully entered
the Circular Channels Mode.
(1) When the sensor’s channel is CH1, need to set up the main unit’s channel
to CH1. Press the “CH/▲” button 1 time to enter the Single Channel Mode.
(2) When the sensor’s channel is CH2, need to set up the main unit’s channel
to CH2. Press the “CH/▲” button 2 times to enter the Single Channel Mode.
(3) When the sensor’s channel is CH3, need to set up the main unit’s channel
to CH3. Press the “CH/▲” button 3 times to enter the Single Channel Mode.
(1) Press and hold “ALARM” button for 3-4 secs to start.
(2) The “Hour” symbol begins to flash. Press “CH/▲” or “MEM/▼” button to
set up “Hour”. Press “ALARM” button to confirm.
(3) The “Minute” symbol begins to flash. Press “CH/▲” or “MEM/▼” button to
adjust the required minute. Press “ALARM” button to save and exit it.
(4) Alarm symbol “ ” will display on screen after successfully setting.
3.5 Alarm Setting
3.4.3 Single Channel Mode Change to Circular Channels Mode
3.4.4 Circular Channels Mode Change to Single Channel Mode
3.5.1 Set Alarm Clock in Order: Hour > Minute> Exit.
You can purchase extra BALDR sensors to expand the monitoring
scope based on one sensor＇s kit.
14

(1) Press “ALARM” button to check alarm time.
(2) Press “ ” button to exit.
(1) Press “ALARM” button to turn OFF/ON alarm.
(2) Alarm symbol “ ” will disappear on screen when in OFF mode or show
on screen when in ON mode.
(3) Press “ ” button to exit.
(4) When the alarm is ringing, the alarm symbol “ ” will flashing and
ascending “Bibi” alarm sound will last for 2 minutes.
Press any other button except “ ” button to stop the alarm. And the
alarm will restart next day.
(1)
When the alarm is ringing, press the “ ” button to enter snooze mode,
the alarm will ring again in 5 minutes snooze interval. And the “ ” symbol
will be flashing on screen to indicate the snooze mode. Press any other button
except top button to exit the snooze mode. And the alarm will restart next day.
(2) When the alarm rings, the ascending “Bibi” alarm sound will last for 2
minutes If no operation, or you can press any other button except “ ”
button to stop the alarm.
Press the “ ” button, the backlight will light up for 20 seconds.
3.6 Backlight
3.5.2 Check Alarm Time
3.5.3 Alarm OFF/ON
3.5.4 Snooze Mode
15

If the battery icon appears on the right side of the indoor data, the
batteries of main unit should be replaced soon.
If the battery icon appears on the right side of the outdoor data, the
batteries of sensor should be replaced soon.
3.7 Low Battery Indication
When the power is about to run out, any buttons and operations will
not respond.
Problem
No Outdoor Sensor
Reception/Outdoor
temperature is
flashing or showing
dashes
If the wireless signal indicator shows"--", which means that
lose the connection or wireless interference.
Way 1 :
(1)Remove the batteries of sensor.
(2)Press and hold the “CH/▲” button for 3-4s, then reload
the sensor battery.
Notes:If the re-connection succeeds, but it breaks again
after a period of time, please place the outdoor sensor at
new location no more than 330 feet (100 meters, open air)
from the weather station.
Way 2 : Factory Restart.
(1)Remove all the batteries of sensor and main unit.
(2)Set the outdoor sensor channel to CH1.
(3)
Power on the main unit and set main unit’s channel to CH1.
(4)Then power on the sensor.
(5)Place the main unit and outdoor sensor at the same
position for half an hour or more after powering on to
establish a strong connection.
Possible Solution
4.TROUBLESHOOTING
16

Outdoor
temperature/humidity
always keep cycling
and show one value
and two "--"
Inaccurate
temperature
or humidity
It means that you have entered Circular Channel Mode.
Please refer to 14th page to turn to Single Channel Mode.
Make sure both unit are placed out of direct sunlight and
away from any heat sources or vents. Please turn to 9th
page to get more details to correct it.
Inaccurate Weather
forecast
This weather station has 5 forecast icons that predict the
weather condition of the next 12-hours based on the change
of temperature, humidity. It is not current time.
Incorrect weekday
display
Insufficient
transmission
distance
The default “ Year” setting of main unit is 2020. Press and
hold “SET/C/F” button for 3-4 seconds to enter the time
setting. Please “SET/C/F” button to skip step until “Year”
setting. Please set current year.
Main unit and sensor transmits range up to 328ft/100m
without obstruction. You are near the sensor to connect
the main unit. Avoid thick walls between the units or or
strong interference source using same signal frequency
(433ghz).(such as tvs, microwaves, computers, etc).
If your BALDR weather station still can't be worked well after trying the
troubleshooting steps, please email us by [email protected] for help.
17