Balluff BIS U-620-068-1X1-00-SX User manual

BF-IDU07
BIS U-620-068-1X1-00-SX
Ultra High Frequency Passive Radio Frequency,
Identification Processor
INSTALLATION GUIDE
This document provides instructions and information
designed to assist users in the hardware setup of the BIS U-
620-068-1x1-00-Sx Processor. For configuration details see
the BIS U-62_ Processor Manual.
PACKAGE CONTENTS
Qty
Description
1
BIS U-620-068-1x1-00-Sx Processor
1
UHF Series Configuration Tag
1
This Installation Guide
TECHNICAL DATA
ELECTRICAL FEATURES
Power Supply
19.2…28.8 V DC
DC Input Current
1 A
Communication Interface
Baud Rate
RS232
9600 (default) …115200
RADIO FEATURES
EU
US
Frequency (MHz)
ETSI EN 302 208
865…868
-
FCC part 15.247
-
902…928
Number of Channels
4 fixed
50 hopping
Frequency Tolerance
± 10 ppm over entire temp
range
Air Interface
EPC C1G2
Conducted Output Power
500 mW (27 dBm) max
Antenna Connector
Reverse TNC
ENVIRONMENTAL FEATURES
Operating Temperature
-20…+50 °C
(-4…+122 °F)
Storage Temperature
-20…+70 °C
(-4…+158 °F)
Humidity max.
90 % non condensing
Vibration Resistance
EN 60068-2-6
14 mm @ 2…10 Hz;
1.5 mm @ 13…55 Hz;
2 g @ 70…200 Hz;
2 hours on each axis
Shock Resistance
EN 60068-2-27
30 g; 11 ms;
3 shocks on each axis
Protection Class
EN 60529
IP65*
PHYSICAL FEATURES
Dimensions
164 x 112 x 48 mm
(6.46 x 4.41 x 1.88 in)
Weight
560 g (19.8 oz)
Enclosure
Powder Coated Aluminum
USER INTERFACE
LED Indicators
READY, RF, COM
* When all connectors and antenna are correctly installed.
The BIS U-620-068-1x1-00-Sx Processor and its antenna
are intended for indoor use only.
GENERAL VIEW
LED INDICATORS
green
READY
The READY LED is ON after the power
up sequence has completed.
amber
RF
The RF LED illuminates when RF
power is being transmitted by the
antenna.
amber
COM
The COM (communications) LED
flashes ON and OFF when data is
being transmitted between the antenna
and a tag.
When in Continuous Read mode, the
COM LED will remain ON and will turn
OFF briefly only while data is being
read from or written to a tag.
CONNECTIVITY
M12 8 pin Male Connector (Data and Power Supply)
Typical Layout
See the BIS U-62_ Processor Manual for a complete list of accessories including
alternative cables and connectors.
DIGITAL I/O (-12 MODELS)
DIMENSIONS
M12 8-pin Female Connector (Digital I/O)
This connector is available on models
BIS U-620-068-1x1-00-S29.
See the BIS U-62_ Processor Manual for details
INSTALLATION GUIDELINES
•RF performance and read/write range can be negatively
impacted by the proximity of metallic objects and liquids.
Avoid mounting the BIS U-3x… antenna within 15 cm (6
inches) of any metallic object or wet surface.
•Do not route cables near other unshielded cables or
near wiring carrying high voltage or high current. Cross
cables at perpendicular intersections and avoid routing
cables near motors and solenoids.
•Avoid mounting the Processor near sources of EMI
(electro-magnetic interference) or near devices that
generate high ESD (electro-static discharge) levels.
Always use adequate ESD prevention measures to
dissipate potentially high voltages.
•If electrical interference is encountered (as indicated by
a significant reduction in read/write performance),
relocate the Processor to an area free from potential
sources of interference.
INSTALLATION
The BIS U-620-068-1x1-00-Sx RFID Processor is designed
for point-to-point RFID applications, where the distance from
host to Processor is less than 15 meters (50 feet). The
Processor connects directly to a serial communications port
on a host computer via an RS232-compatible serial
interface cable.
1. Select a suitable location for the BIS U-62… Processor
and BIS U-30… Antenna.
2. Mount the BIS U-30… Antenna (within the cable
distance of the Processor) and attach the BIS U-30…
Antenna cable as described in the installation guide
included with the antenna.
3. Fasten the Processor to your mounting fixture using two
M5 (#10) diameter screws (not included) and secure
them with appropriate washers and nuts. Tighten
screws to 1.7 Nm or 15 lbs per inch ± 10%. Connect
the antenna cable to the UHF Processor.
4. Connect the BCC0ETJM12 8-pin female connector to
the M12 8-pin male interface connector on the BIS U-
620-068-1x1-00-Sx Processor. Connect the
BCC0ETJ9-pin female D-sub connector to an RS232
COM port on the host computer. Tighten the cable’s
two locking thumbscrews.
5. Connect the power supply to the VDC (red) and GND
(black) wires on the BCC0ETJcable.
6. Apply power to the Processor after all cable
connections have been made. The LEDs on the unit will
flash. The READY LED is ON after the power up
sequence has completed.
7. On the host computer, set the COM port parameters to:
9600 baud, 8 data bits, 1 stop bit, no parity and no
handshaking.
To verify operations, download the Balluff Dashboard™
Configuration Tool from www.balluff.com. The Balluff
Dashboard™Configuration Tool allows users to configure
and control their BIS U-620-068-1x1-00-Sx Processors and
send RFID commands for testing purposes.
BIS U-620-068-1x1-
BCC0ETJ
Host
Power
Supply
BIS U-30x… antenna
Vdc (red)
GND (black)
mm
in
* Digital I/O (-ST29 models only)
*
*
*
zur Prüfung

COMPL IANCE
Only BIS U-30… family antennas are certified for use
with the BIS U-620-068-1x1-00-Sx Processors.
This product is intended to be installed by Qualified
Personnel only.
This product must not be used in explosive environments.
Power Supply
This device is intended to be supplied by a UL Listed or
CSA Certified Power Unit with «Class 2» or LPS power
source.
BIS U-620-068-101-00-Sx:
No. 890 426 EN .H17; Subject to modification. Replaces 1305.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment offand on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.
Changes or modifications not expressly approved by the party
responsible for compliance voids the user's authority to operate
this equipment.
This device complies with part 15 of the FCC Rules and
Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Radiofrequency radiation exposure Information:
This equipment complies with FCC and IC radiation exposure
limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d'exposition aux
rayonnements IC établies pour un Environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.
Ce transmetteur ne doit pas être place au même endroit ou utilise
simultanément avec un autre transmetteur ou antenne.

BF-IDU07
BIS U-626-069-1X1-06-S3X
Ultra High Frequency Passive Radio Frequency,
Identification Processor
INSTALLATION GUIDE
This document provides instructions and information
designed to assist users in the hardware setup of the BIS U-
626-069-1x1-06-S3x Processor . For configuration details
see the BIS U-62_ Processor Manual.
PACKAGE CONTENTS
Qty
Description
1
BIS U-626-069-1x1-06-S3x Processor
1
UHF Series Configuration Tag
1
This Installation Guide
1
BCC06ZF Power Connector
TECHNICAL DATA
ELECTRICAL FEATURES
Power Supply
19.2…28.8 V DC
DC Input Current
1 A
Communication Interface
Industrial Ethernet,
TCP/IP, MODBUS TCP
Baud Rate
10/100 Mbps
RADIO FEATURES
EU
US
Frequency (MHz)
ETSI EN 302 208
865…868
-
FCC part 15.247
-
902…928
Number of Channels
4 fixed
50 hopping
Frequency Tolerance
± 10 ppm over entire temp
range
Air Interface
EPC C1G2
Conducted Output Power
500 mW (27 dBm) max
Antenna Connector
Reverse TNC
ENVIRONMENTAL FEATURES
Operating Temperature
-20…+50 °C
(-4…+122 °F)
Storage Temperature
-20…+70 °C
(-4…+158 °F)
Humidity max.
90% non condensing
Vibration Resistance
EN 60068-2-6
14 mm @ 2…10 Hz;
1.5 mm @ 13…55 Hz;
2 g @ 70…200 Hz;
2 hours on each axis
Shock Resistance
EN 60068-2-27
30 g; 11 ms;
3 shocks on each axis
Protection Class
EN 60529
IP65
PHYSICAL FEATURES
Dimensions
164 x 112 x 48 mm
(6.46 x 4.41 x 1.88 in)
Weight
560 g (19.8 oz)
Enclosure
Powder Coated Aluminum
USER INTERFACE
LED Indicators
READY, RF, COM,
DEFAULT IP, CUSTOM IP
* When all connectors and antenna are correctly installed.
The BIS U-626-069-1x1-06-S3x Processor and its
antenna are intended for indoor use only
GENERAL VIEW
LED INDICATORS
green
READY
The READY LED is ON after the power
up sequence has completed.
amber
RF
The RF LED illuminates when RF
power is being transmitted by the
antenna.
amber
COM
The COM (communications) LED
flashes ON and OFF when data is
being transmitted between the antenna
and a tag.
When in Continuous Read mode, the
COM LED will remain ON and will turn
OFF briefly only while data is being
read from or written to a tag.
amber
DEFAULT
Default IP Address enabled
(192.168.253.110)
amber
CUSTOM
User assigned IP Address enabled
CONNECTIVITY
M12 4-pin D-Coded Female Connector (for Ethernet)
M12 5-pin Male Connector (for Power Supply)
DIGITAL I/O (-12 MODELS)
M12 8-pin Female Connector (Digital I/O)
This connector is available on models
BIS U-620-067-1x1-04-S32.
See the BIS U-62_ Processor Manual for details.
Typical Layout
See the BIS U-62_ Processor Manual for a complete list of accessories including
alternative cables and connectors.
DIMENSIONS
INSTALLATION GUIDELINES
•RF performance and read/write range can be negatively
impacted by the proximity of metallic objects and liquids.
Avoid mounting the BIS U-3x… antenna within 15 cm (6
inches) of any metallic object or wet surface.
•Do not route cables near other unshielded cables or
near wiring carrying high voltage or high current. Cross
cables at perpendicular intersections and avoid routing
cables near motors and solenoids.
•Avoid mounting the Processor near sources of EMI
(electro-magnetic interference) or near devices that
generate high ESD (electro-static discharge) levels.
Always use adequate ESD prevention measures to
dissipate potentially high voltages.
•If electrical interference is encountered (as indicated by
a significant reduction in read/write performance),
relocate the Processor to an area free from potential
sources of interference.
INSTALLATION
The BIS U-626-069-1x1-06-S3x Processor is designed for
Industrial Ethernet RFID applications, where the Processor
is connected in an Industrial Ethernet or TCP/IP network via
compatible cables through a hub or directly to an Industrial
Ethernet host.
1. Select a suitable location for the BIS U-62… Processor
and BIS U-30… Antenna.
2. Mount the BIS U-30… Antenna (within the cable
distance of the Processor) and attach the BIS U-30…
Antenna cable as described in the installation guide
included with the antenna.
3. Fasten the Processor to your mounting fixture using
two M5 (#10) diameter screws (not included) and
secure them with appropriate washers and nuts.
Tighten screws to 1.7 Nm or 15 lbs per inch ± 10%.
Connect the antenna cable to the UHF Processor .
4. Connect the BCC0CT1 M12 4-pin male connector to
the M12 4-pin female interface connector on the BIS U-
626-069-1x1-06-S3x Processor. Connect the BCC0CT1
RJ45 male connector to the LAN hub/switch. If
connecting directly to the host computer you will need
to use an additional crossover cable.
5. Build a power supply cable using the BCC06ZF M12 5-
pin female connector. Use minimum 24 AWG wires for
connection to the power supply lines according to the
Vdc connector pinout. Connect the BCC06ZF M12 5-
pin female connector to the M12 5-pin male connector
on the Processor . Connect the other end of the cable
(wires or user-supplied connectors) to the power
supply.
6. Apply power to the Processor after all cable
connections have been made. The LEDs on the unit will
flash. The READY LED is ON after the power up
sequence has completed. Then one of the Industrial
Ethernet Address LEDs will remain on either Default or
Custom.
To verify operations, download the Balluff Dashboard™
Configuration Tool from www.balluff.com. The Balluff
Dashboard™Configuration Tool allows users to configure
and control their BIS U-626-069-1x1-06-S3x Processor s
and send RFID commands for testing purposes.
For connection details see the BIS U-62_ Processor
Manual and the Balluff Dashboard™Configuration Tool
Manual.
PIN 4:
RX-
PIN 1:
TX+
PIN 3:
TX-
PIN 2:
RX+
PIN 4:
N/C
PIN 3:
GND
PIN 5:
N/C
PIN 1:
N/C
PIN 2:
VDC
BIS U-626-069
Vdc
BCC0CT1
Hub
PLC
BCC06ZF
BIS U-30x… antenna
to Power Supply
GND
mm
in
* Digital I/O (-S32 models only)
*
*
*
zur Prüfung

COMPL IANCE
Only BIS U-30… family antennas are certified for use
with the BIS U-626-069-1x1-06-S3x Processors.
This product is intended to be installed by Qualified
Personnel only.
This product must not be used in explosive environments.
Only connect Ethernet and dataport connections to a
network which has routing only within the plant or
building and no routing outside the plant or building.
Power Supply
This device is intended to be supplied by a UL Listed or
CSA Certified Power Unit with «Class 2» or LPS power
source.
BIS U-626-069-101-06-S3x:
No. 890 428 EN .H17; Subject to modification. Replaces 1305.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment offand on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.
Changes or modifications not expressly approved by the party
responsible for compliance voids the user's authority to operate
this equipment.
This device complies with part 15 of the FCC Rules and
Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Radiofrequency radiation exposure Information:
This equipment complies with FCC and IC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance of 20 cm between the
radiator and your body.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Cet équipement est conforme aux limites d'exposition aux
rayonnements IC établies pour un Environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un minimum de 20 cm de
distance entre la source de rayonnement et votre corps.
Ce transmetteur ne doit pas être place au même endroit ou utilise
simultanément avec un autre transmetteur ou antenne.