Banner QM26 Series User manual

Instrucon Manual
Stainless Steel and Hygienic Stainless Steel Sensors for Washdown and Chemical Compability
•QM26: Washdown rated with convenient 25.4 mm (1 in) mounng spacing and 3 mm (0.125 in)
mounng hardware
•QMH26: Hygienic shape for superior cleaning performance
•Made from FDA compliant materials for worry-free use in food and pharmaceucal applicaons
• Chemically resistant, non-toxic 316L stainless steel housing
• Acrylic opcal window with coang for resistance to hydrogen peroxide and alcohol
•IP69K rated for use in harsh 1500 psi washdown environments at 80° C (176° F)
• Withstands environmental temperature cycling from –30° to +60° C (–22° to +140° F)
• Sealed housing and smooth joints minimize cleaning me and reduce bacterial accumulaon
• Sensor marking is chemically etched into the housing for long-lasng idencaon and to
eliminate food contaminaon
• Push buons and light pipes are over-molded to reduce crevices and provide excellent cleaning
and sealing results
• High performance coaxial polarized retroreecve models for clear or transparent bole and lm
detecon
• Excellent background suppression performance with advanced ambient light suppression
•Bright, visible red light spot on adjustable background suppression models makes alignment easy
• Models have a hygienic design for easy cleaning and sanizing
WARNING: Not To Be Used for Personnel Protecon
Never use this device as a sensing device for personnel protecon. Doing so could lead to serious injury or death.
This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety
applicaons. A sensor failure or malfuncon can cause either an energized or de-energized sensor output
condion.
QM26 Models
Stainless Steel Sensors for Washdown and Chemical Compability
Model Mode Range Output Connector
QM26E-5M Emier
8.5 m (27.8 )
NA 5 m (16.25 ) cable, 4 wire
QM26EQ5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26VNR-5M
Receiver
Complementary
NPN
5 m (16.25 ) cable, 4 wire
QM26VNRQ5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26VPR-5M Complementary
PNP
5 m (16.25 ) cable, 4 wire
QM26VPRQ5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26VNLP-5M
Polarized
Retroreecve
3 m (9.8 ) with
BRT-60X40C
Complementary
NPN
5 m (16.25 ) cable, 4 wire
QM26VNLPQ5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26VPLP-5M Complementary
PNP
5 m (16.25 ) cable, 4 wire
QM26VPLPQ5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26ENXLPC-5M
Expert™Coaxial
Polarized
Retroreecve
2.6 m (8.5 ) with
BRT-60X40C
NPN 5 m (16.25 ) cable, 4 wire
QM26ENXLPCQ5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26EPXLPC-5M PNP 5 m (16.25 ) cable, 4 wire
QM26EPXLPCQ5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26 and QMH26 Series Sensors
Original Document
166534 Rev. E 16 October 2017
166534

Model Mode Range Output Connector
QM26VNAF400-5M
Adjustable Field
Background
Suppression
5 to 400 mm (0.2 in
to 15.7 in)
Complementary
NPN
5 m (16.25 ) cable, 4 wire
QM26VNAF400Q5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26VPAF400-5M Complementary
PNP
5 m (16.25 ) cable, 4 wire
QM26VPAF400Q5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26VNAF200-5M Adjustable Field
Background
Suppression (small
light spot) And
5 to 200 mm (0.2 in
to 7.85 in)
Complementary
NPN
5 m (16.25 ) cable, 4 wire
QM26VNAF200Q5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QM26VPAF200-5M Complementary
PNP
5 m (16.25 ) cable, 4 wire
QM26VPAF200Q5 200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QMH26 Models
Hygienic Stainless Steel Sensors for Washdown and Chemical Compability
Model Mode Range Output Connector
QMH26VNLP-5M
Polarized Retroreecve 3m (9.8 ) with BRT-60X40C
Complementary NPN 5 m (16.25 ) cable, 4 wire
QMH26VNLPQ7 M8 Pico QD connector, 4-pin
QMH26VPLP-5M Complementary PNP 5 m (16.25 ) cable, 4 wire
QMH26VPLPQ7 M8 Pico QD connector, 4-pin
QMH26ENXLPC-5M
Expert™Coaxial Polarized
Retroreecve 2.6 m (8.5 ) with BRT-60X40C
NPN 5 m (16.25 ) cable, 4 wire
QMH26ENXLPCQ7 M8 Pico QD connector, 4-pin
QMH26EPXLPC-5M PNP 5 m (16.25 ) cable, 4 wire
QMH26EPXLPCQ7 M8 Pico QD connector, 4-pin
QMH26VNAF400-5M
Adjustable Field Background
Suppression 5 to 400 mm (0.2 in to 15.7 in)
Complementary NPN 5 m (16.25 ) cable, 4 wire
QMH26VNAF400Q7 M8 Pico QD connector, 4-pin
QMH26VPAF400-5M Complementary PNP 5 m (16.25 ) cable, 4 wire
QMH26VPAF400Q7 M8 Pico QD connector, 4-pin
QMH26VNAF200-5M
Adjustable Field Background
Suppression (small light spot) 5 to 200 mm (0.2 in to 7.85 in)
Complementary NPN 5 m (16.25 ) cable, 4 wire
QMH26VNAF200Q7 M8 Pico QD connector, 4-pin
QMH26VPAF200-5M Complementary PNP 5 m (16.25 ) cable, 4 wire
QMH26VPAF200Q7 M8 Pico QD connector, 4-pin
Overview
QMH26 QM26 Key
2
3
4
1
2
3
4
1
1. Green Indicator
2. Yellow Indicator
3. Push Buon
Adjustment Screw/Potenometer (not shown)—AFxxx
models
4. Opcal Window
QM26 and QMH26 Series Sensors
2 www.bannerengineering.com - Tel: [phone] P/N 166534 Rev. E

Sensor Installaon
Install the sensor so that the object to be detected moves horizontally to the sensor.
Wiring Diagrams
1
3
4
2
10-30V dc
–
+
Remote
Programming
Load
Expert™NPN
1
3
4
2
10-30V dc
–
+
Remote
Programming
Load
Expert™PNP
Wiring Key
1 = Brown
2 = White
3 = Blue
4 = Black
10-30V dc
–
+
1
3
2
4Load
Load
NPN
10-30V dc
–
+
1
3
2
4Load
Load
PNP
10-30V dc
Beam
Enable
1
–
+
3
4
2N.C.
QM26—Emiers
Sensor Conguraon
• Adjustable eld background suppression models (AFxxx models) have an 8-turn adjustment screw (potenometer) to set the
background suppression distance.
•Expert™coaxial polarized retroreecve models (XLPC models) are congurable using either the sealed push buon or the
remote input wire.
•Two-lens polarized retroreecve models (LP models) and opposed mode models require no user adjustments.
Sensor Setup - Background Suppression—AFxxx Models
Background Suppression Mode: Objects beyond the set cuto distance will not be detected.
Background suppression mode can be used in most situaons with varying object colors and posions or with varying background
condions.
To ensure reliable background suppression, a minimum separaon distance between the object and the background is necessary. See
Figure 5 on page 10 to determine the minimum separaon distance.
QM26 and QMH26 Series Sensors
P/N 166534 Rev. E www.bannerengineering.com - Tel: [phone]

1. Mount the sensor with the darkest object at the longest applicaon
distance. The distance to the object must be less than shown in
Figure 5 on page 10 for your object color.
2. Turn the adjustment potenometer counter-clockwise unl the
yellow indicator turns o (8 turns maximum).
3. Turn the adjustment potenometer clockwise unl the yellow
indicator turns on.
4. Replace the darkest object with the brightest background at the
closest applicaon distance.
5. Turn the adjustment potenometer clockwise, counng the
revoluons, unl the yellow indicator turns on.
6. Turn the adjustment potenometer counter-clockwise half of the
number of turns from step 5. This places the cuto distance midway
between the object and the background switchpoints (see Figure 1
on page 4).
The sensor is ready for operaon.
Object Background
Cutoff
Distance
X
Y
X: Distance to the Object
Y: Minimum Separaon Between the Object and
the Background Figure 1.
Set the cuto distance approximately midway
between the farthest object and the closest
background
Setup Example
An object with a reecvity similar to black paper is set 100 mm (3.9 in) away
from the AF200 sensor. A background with a reecvity similar to white paper
is set away from the sensor. According to Figure 5 on page 10 , the minimum
separaon distance between the object and the background is 24 mm (0.94 in).
In this applicaon, reliable detecon is achieved when set up according to the
procedure outlined in Sensor Setup - Background Suppression—AFxxx Models
on page 3.
2
Y
3
1
X
Figure 2. Background Suppression Mode Applicaon
Example
1. Object
2. Conveyor
3. Background
X: Distance to the Object = 100 mm (3.9 in)
Y: Minimum Separaon Between the Object and
the Background = 24 mm (0.94 in)
Remote Conguraon—XLPC models
The remote input wire (pin 2/white wire) is used to to lock the push buon, select Light or Dark Operate, or perform the desired Light
SET or Dark SET for the object. In contrast to other Banner Engineering sensors, the QM26 and QMH26 Expert™coaxial polarized
retroreecve sensors (XLPC models) use the duraon between pull-high pulses on the remote input wire to both iniate the Light SET
or Dark SET and to select the desired sensivity simultaneously. See Light SET for High Sensivity on page 5, Light SET for Medium
Sensivity on page 6, and Dark SET for Maximum Operang Range on page 7 for details.
Note: Aer the delay before startup has elapsed ( ≤300 ms), the remote input may be used.
Push Buon Lockout—XLPC Models
The remote input wire (pin 2/white wire) can be used to disable the sensor push buon on the XLPC models to prevent unauthorized
adjustment to the sensor. Connect the remote input wire (pin 2/white wire) of the sensor to the +V dc terminal to disable conguraon
adjustments using the push buon.
QM26 and QMH26 Series Sensors
4 www.bannerengineering.com - Tel: [phone] P/N 166534 Rev. E

Push Buon Remote Input Wire Result
Not available Connect the remote input wire to +V dc for 4 ms or longer. The push buon is disabled (locked).
Not available Disconnect the remote input wire from +V dc. The push buon is enabled (unlocked).
Select Light Operate/Dark Operate—XLPC models
Change the sensor operaon to light operate or dark operate for the desired applicaon. Use either the buon or the remote input wire
procedure to congure the sensor.
Push Buon Remote Input Wire Result
Press and hold the buon for longer
than 12 s.
Connue pressing the buon unl the
desired operaon is selected, then
release the buon.
> 12 sec.
Pulse the remote input wire to +V dc, then pull the
remote input wire to ground for 2000 to 3000 ms.
Light operate select: Pulse the remote input wire to +V
dc for 4 to 1000 ms, then pull the remote input wire to
ground.
+Vdc
L.O.
Teach Input
2000 ... 3000 ms
p light
4 .. 1000 ms
0
t
tt
t = 0
Dark operate select: Pulse the remote input wire to +V
dc for 1000 to 2000 ms, then pull the remote input wire
to ground.
D.O.
p dark
1000 .. 2000 ms
Teach Input
2000 ... 3000 ms
+Vdc
0
t
tt
t = 0
Push buon only: The green LED ashes.
LED
Green
Flashing
LED
Yellow
OFF
Yellow LED ON = Light operate
LED
Green
Flashing
LED
Yellow
ON
Yellow LED OFF = Dark operate
LED
Green
Flashing
LED
Yellow
OFF
The sensor is congured for the desired mode
and is ready.
Light SET—XLPC Models
A Light SET opmizes the sensor to provide reliable detecon of
various objects. For most applicaons, the factory default seng
is appropriate. Perform the Light SET only if the desired object is
not reliably detected. Stable mounng of both the sensor and
the reector is required for reliable detecon.
• High sensivity (11% oset)—suitable for highly
transparent boles, thin lms, and foils. See Light SET
for High Sensivity on page 5.
• Medium sensivity (18% oset)—suitable for standard
bole types and translucent objects. See Light SET for
Medium Sensivity on page 6.
Darkest
(no signal)
Most Light
(saturated
signal)
Output ON Output OFF
Single
Presented
Condition
Sensor positions
threshold ≈ X % below
the presented condition
Figure 3. Light SET (Dark Operate Shown)
Light SET for High Sensivity
Use High Sensivity (11% sensivity) for detecng highly transparent boles, thin lms, and foils with a thickness of more than 20 µm.
Use either the buon or the remote input wire procedure to congure the sensor.
QM26 and QMH26 Series Sensors
P/N 166534 Rev. E www.bannerengineering.com - Tel: [phone]

Push Buon Remote Input Wire Result
Clear the light path to the reector. Clear the light path to the reector.
Press the buon for 2 to 7 seconds unl
the LEDs ash simultaneously, then
release the buon.
2 to 7 sec.
Pulse the remote input wire to +V dc, then pull the
remote input wire to ground for 4 to 1000 ms.
Pulse the remote input wire to +V dc to complete the
high sensivity Light SET.
t = 0
+Vdc
Teach
4 ... 1000 ms
0
t
t
Push buon only: The green and yellow LEDs
ash simultaneously.
LED
Yellow
LED
Green
SIMULTANEOUS
Flashing at
3Hz
The sensor is congured for High Sensivity and
is ready for use.
Light SET for Medium Sensivity
Use Medium Sensivity (18% sensivity) for detecng standard bole types and translucent objects. Use either the buon or the
remote input wire procedure to congure the sensor.
Push Buon Remote Input Wire Result
Clear the light path to the reector. Clear the light path to the reector.
Press the buon for 7 to 12 seconds
unl the LEDs ash alternately, then
release the buon.
7 to 12 sec.
Pulse the remote input wire to +V dc, then pull the
remote input wire to ground for 1000 to 2000 ms.
Pulse the remote input wire to +V dc to complete the
medium sensivity Light SET.
+Vdc
Teach
1000 ... 2000 ms
0
t
t
t = 0
Push buon only: The green and yellow LEDs
ash alternately.
LED
Yellow
LED
Green
ALTERNATELY
Flashing at
3Hz
The sensor is congured for Medium Sensivity
and is ready for use.
Dark SET—XLPC Models
Dark SET (maximum operang range) is the factory default
seng and provides maximum sensing range, ease of
alignment, and reliable detecon of brown or green boles
and opaque objects.
Most Light
(no signal)
Darkest
(saturated
signal)
Output OFFOutput ON
Single
Presented
Condition
Sensor positions threshold
above the present condition
for max. operating range
Figure 4. Dark SET (Dark Operate Shown)
QM26 and QMH26 Series Sensors
6 www.bannerengineering.com - Tel: [phone] P/N 166534 Rev. E

Dark SET for Maximum Operang Range
Use either the buon or the remote input wire procedure to congure the sensor.
Push Buon Remote Input Wire Result
Block the light path to the reector. Block the light path to the reector.
Press the buon for 2 to 7 seconds unl
the LEDs ash simultaneously, then
release the buon.
2 to 7 sec.
Pulse the remote input wire to +V dc, then pull the
remote input wire to ground for 4 to 1000 ms.
Pulse the remote input wire to +V dc to complete the
Dark SET.
t = 0
+Vdc
Teach
4 ... 1000 ms
0
t
t
Push buon only: The green and yellow LEDs
ash simultaneously.
LED
Yellow
LED
Green
SIMULTANEOUS
Flashing at
3Hz
The sensor is congured for Dark SET (maximum
operang range).
Clear the light path to the reector. Clear the light path to the reector.
The sensor is ready for use.
QM26 and QMH26 Series Sensors
P/N 166534 Rev. E www.bannerengineering.com - Tel: [phone]

Specicaons
Supply Voltage and Current
10 to 30 V dc (10% maximum ripple within specied limits); supply current
(exclusive of load current) < 20 mA
Note: For UL applicaons: For use in class 2 circuits
only.
Supply Protecon Circuitry
Protected against reverse polarity and transient voltages
Output Conguraon
XLPC models: Single PNP or NPN on pin 4 (black wire) with remote input on pin
2 (white wire)
All other models: Complementary PNP or NPN by model number
Delay Before Power-Up
< 300 ms
Output Rang
100 mA per output
O-state leakage current for load = 1500 Ω:
NPN: < 200 μA
PNP: < 500 μA
ON-state saturaon voltage: < 2 V at 100 mA
Output Protecon Circuitry
Protected against false pulse at power up, and overload or short circuit of
outputs
Emier LED Wavelength
AF200 models: 660 nm
All other models: 620 nm
Required Overcurrent Protecon
WARNING: Electrical connecons must be made
by qualied personnel in accordance with local
and naonal electrical codes and regulaons.
Overcurrent protecon is required to be provided by end product applicaon
per the supplied table.
Overcurrent protecon may be provided with external fusing or via Current
Liming, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For addional product support, go to www.bannerengineering.com.
Supply Wiring (AWG) Required Overcurrent Protecon (Amps)
20 5.0
22 3.0
24 2.0
26 1.0
28 0.8
30 0.5
Output Response Time
500 µs
Repeatability
QM26—Opposed Models: 110 μs
All other models: 150 μs
Indicators
Green on: Power ON and sensor ready
Yellow on: Light sensed
XLPC models—Yellow ashing: Light sensed but marginal signal
Construcon
Housing: 316L stainless steel
Opcal Window: Coated acrylic (PMMA)
Indicator and buons: TPV - PE
Connecon
4-wire 5 m (16.25 ) cable or 4-pin M12 Euro-style quick disconnect connector
with 200 mm (7.5 in) PVC pigtail, depending on model
Banner recommends using the 4-Pin Threaded M12/Euro-Style Cordsets—
Washdown, Stainless Steel cordsets listed in the Accessories secon.
Note: These proximity switches shall be used with
UL Listed Cable assemblies rated 30 V, 0.24 A
minimum, in the eld installaon.
Adjustments
QM26 Emier—Beam Enable: Connect black wire to +V dc to acvate emier
LED
AFxxx models—Adjustment Screw: Sets background suppression distance
XLPC models—Push Buon: User set up
XLPC models—Remote Input Wire: Remote PLC set up and push buon lock
out
Environmental Rang
IEC IP67 and IEC IP69K
Chemical Compability
ECOLAB®cered
Operang Condions
Operang Temperature and Storage Temperature: –30 °C to +70 °C (–22 °F to
+158 °F)
Note: UL cered in the temperature range –30 °C
to +55 °C (–22 °F to +131 °F).
Humidity: Periodic exposure to 100% humidity and washdown cleaning
Vibraon and Shock
IEC60947-5-2
Cercaons
with class 2 power supply
QM26 and QMH26 Series Sensors
8 www.bannerengineering.com - Tel: [phone] P/N 166534 Rev. E

QM26 Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
QMH26 Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
QM26 and QMH26 Series Sensors
P/N 166534 Rev. E www.bannerengineering.com - Tel: [phone]

Performance Curves
Minimum Separaon Distance
AF200 Models AF400 Models
20
25
30
35
40
5
0
10
15
0 50 100 150 200 250
90% White Card Cutoff Setting (mm)
Black / White
Gray / White
White / White
Object / Background
Minimum Separation Between Object
and Background (mm)
40
50
60
70
80
90
10
0
20
30
0 100 200 300 400 500
90% White Card Cutoff Setting (mm)
Minimum Separation Between Object
and Background (mm)
Black / White
Gray / White
White / White
Object / Background
Figure 5. Minimum Separaon Distance
Minimum Sensing Range
AF200 Models AF400 Models
50 50 100 150 200 250
90% White Card Cutoff Setting (mm)
Minimum Range (mm) 6% Blk Card
15
10
0
5
15
10
0
5
0 5 100 200 300 400 500
90% White Card Cutoff Setting (mm)
Minimum Range (mm) 6% Blk Card
Figure 6. Minimum Sensing Range (Dead Zone)
QM26 and QMH26 Series Sensors
10 www.bannerengineering.com - Tel: [phone] P/N 166534 Rev. E

Excess Gain
DISTANCE (mm)
100 1000 10000
110
EXCESS GAIN
100
1000
1
10
Figure 7. Opposed Mode Models
100
100
10001
1
10
10
10000
DISTANCE (mm)
EXCESS GAIN
BRT-60x40C
BRT-92x92C
BRT-40x19A
BRT-60x40IP69K
BRT-THG-2-100 (2” x 2”)
BRT-60x40C-PS
BRT-40x19A-PS
Figure 8. Expert™Retroreecve Models (XLPC Models)
100 10001 10 10000
DISTANCE (mm)
100
1
10
EXCESS GAIN
BRT-60x40C
BRT-92x92C
BRT-40x19A
BRT-60x40IP69K
BRT-THG-2-100 (2” x 2”)
BRT-60x40C-PS
BRT-40x19A-PS
Figure 9. Fixed Gain Retroreecve Models (LP models)
QM26 and QMH26 Series Sensors
P/N 166534 Rev. E www.bannerengineering.com - Tel: [phone]

AF200 Models AF400 Models
DISTANCE (mm)
EXCESS GAIN
100
100
1000
1000
1
1
10
10
Setpoint: 15 mm
Setpoint: 100 mm
Setpoint: 200 mm
DISTANCE (mm)
EXCESS GAIN
100
100
1000
1000
1000
1
1
10
10
Setpoint: 15 mm
Setpoint: 200 mm
Setpoint: 400 mm
Figure 10. Adjustable Field Models (AFxxx Models)
Beam Paerns
20
40
60
80
100
-40
-60
-80
-100
-20
0
0 1000 2000 3000 4000 5000 6000 7000 8000 9000
DISTANCE (mm)
BEAM PATTERN (mm)
Figure 11. Opposed Mode Models
0
50
-50
100
-100
150
-150
10000 2000 3000 4000 5000
DISTANCE (mm)
BEAM PATTERN (mm)
Figure 12. Fixed Gain Retroreecve (LP) Models
20
40
60
-40
-60
-20
0
0 500 1000 1500 2000 2500 3000 3500
DISTANCE (mm)
BEAM PATTERN (mm)
Figure 13. Expert™Retroreecve Models (XLPC ) Models
QM26 and QMH26 Series Sensors
12 www.bannerengineering.com - Tel: [phone] P/N 166534 Rev. E

AF200 Models AF400 Models
0
2
-2
4
-4
6
-6
500 100 150 200 250
DISTANCE (mm)
BEAM PATTERN (mm)
0
2
-2
4
-4
6
8
-6
-8 1000 200 300 400
DISTANCE (mm)
BEAM PATTERN (mm)
Figure 14. Adjustable Field Models (AFxxx Models)
Spot Size Versus Distance
Clear Object Expert Retroreecve (XLPC) Models
80 x 80
100 x 100
20 x 20
0 x 0
40 x 40
60 x 60
0 50 100 150 200 250 300
DISTANCE (mm)
BEAM SPOT SIZE (mm)
Accessories
Cordsets for QM26 Models with Sux Q5
All measurements are listed in millimeters, unless noted otherwise.
4-Pin Threaded M12/Euro-Style Cordsets (Washdown, Stainless Steel) (Recommended)
Cable: PVC cable, stainless steel coupling nut, EPDM o-ring
Conductors: 22 AWG, gold-plated contacts
Voltage/Current Rang: 300 V dc, 4.0 A
Temperature: –40 °C to +105 °C (–40 °F to +221 °F)
Environmental Rang: IEC IP69K
4-Pin Threaded M12/Euro-Style Cordsets—Washdown, Stainless Steel
Model Length Style Dimensions Pinout (Female)
MQDC-WDSS-0406 1.83 m (6 )
Straight
43.5 mm
Ø4.8 mm
Ø15.5 mm
2
3
4
1
1 = Brown
2 = White
3 = Blue
4 = Black
MQDC-WDSS-0415 4.57 m (15 )
MQDC-WDSS-0430 9.14 m (30 )
QM26 and QMH26 Series Sensors
P/N 166534 Rev. E www.bannerengineering.com - Tel: [phone]

4-Pin Threaded M12/Euro-Style Cordsets
Cable: PVC jacket, PUR (polyurethane) connector body, nickel-plated brass coupling nut
Conductors: 22 AWG, gold-plated contacts
Conductors: 22 AWG, gold-plated contacts
Voltage/Current Rang: 250 V ac/dc, 4.0 A
Temperature: –40 °C to +105 °C (–40 °F to +221 °F)
Environmental Rang: IP67/IP69K
4-Pin Threaded M12/Euro-Style Cordsets
Model Length Style Dimensions Pinout (Female)
MQDC-406 1.83 m (6 )
Straight
44 Typ.
ø 14.5
M12 x 1
2
3
4
1
1 = Brown
2 = White
3 = Blue
4 = Black
MQDC-415 4.57 m (15 )
MQDC-430 9.14 m (30 )
MQDC-450 15.2 m (50 )
Cordsets for QMH26 Models with sux Q7
All measurements are listed in millimeters, unless noted otherwise.
4-Pin Threaded M8/Pico-Style Cordsets
Model Length Style Dimensions Pinout (Female)
PKG4M-2 2 m (6.56 )
Straight
ø 9.5
35 Typ.
M8 x 1
4
31
2
1 = Brown
2 = White
3 = Blue
4 = Black
PKG4M-5 5 m (16.4 )
PKG4M-9 9 m (29.5 )
PKW4M-2 2 m (6.56 )
Right Angle
ø 9.5
28 Typ.
20 Typ.
M8 x 1
PKW4M-5 5 m (16.4 )
PKW4M-9 9 m (29.5 )
Brackets for QM26 Models
All measurements are listed in millimeters, unless noted otherwise.
SMBLSTDLQ26
•Adjustable right-angle
metal bracket
• 304 stainless steel
15 15
35
SMBLSTQ26
•Right-angle bracket
• 304 stainless steel
15
72
32
Brackets for QMH26 Models
All measurements are listed in millimeters, unless noted otherwise.
QM26 and QMH26 Series Sensors
14 www.bannerengineering.com - Tel: [phone] P/N 166534 Rev. E

SMBQMH26-SS-150
•Smooth surfaces for easy
cleaning
• Setscrew adjustment of
sensor
• 316L stainless steel
ø 12
150
ø 22
Retroreectors
All measurements are listed in millimeters, unless noted otherwise.
BRT-60X40C
•Rectangular, acrylic target
•Reecvity Factor: 1.4
•Temperature: –20 °C to +60 °C (–4 °F
to +140 °F)
•Oponal brackets are available
•Approximate size: 40 mm × 60 mm
BRT-92X92C
•Square, acrylic target
•Reecvity Factor: 3.0
•Temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
•Oponal brackets are available
•Approximate size: 92 mm × 92 mm
BRT-40X19A
•Rectangular, acrylic target
•Reecvity Factor: 1.3
•Temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
• Approximate size: 19 mm × 60 mm
overall; 19 mm × 40 mm reector
BRT-60X40IP69K
•Rectangular, acrylic target (color is
amber)
•Reecvity Factor: 0.7
•Temperature: –20 °C to +140 °C (–4 °F
to +284 °F)
• Chemically resistant
• IP69K washdown rated
•Oponal brackets are available
•Approximate size: 40 mm × 60 mm
BRT-60X40C-PS
•Rectangular, polystyrene target
•Reecvity Factor: 1.1
•Temperature: –20 °C to +60 °C (–4 °F
to +140 °F)
•Oponal brackets are available
•Chemically compable with hydrogen
peroxide
•Yellow back
• Approximate size: 40 mm × 60 mm
BRT-40X19A-PS
•Rectangular, polystyrene target
•Reecvity Factor: 1.0
•Temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
• Chemically compable with hydrogen
peroxide
•Yellow back
• Approximate size: 19 mm × 60 mm
overall; 19 mm × 40 mm reector
Model Reecvity Factor Maximum Temperature Size
BRT-THG-2-100 0.7 +60 °C (+140 °F) 50 mm (2 in) wide, 2.5 m (100 in) long
QM26 and QMH26 Series Sensors
P/N 166534 Rev. E www.bannerengineering.com - Tel: [phone]

Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture which, at the me it is returned to the factory, is found to have been defecve during the warranty period. This warranty does not cover
damage or liability for misuse, abuse, or the improper applicaon or installaon of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discreon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY
OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT
DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaons or liabilies relang to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper applicaon or installaon of this product or use of the product for personal protecon applicaons when the
product is idened as not intended for such purposes will void the product warranty. Any modicaons to this product without prior express approval by Banner Engineering Corp will void the
product warranes. All specicaons published in this document are subject to change; Banner reserves the right to modify product specicaons or update documentaon at any me.
Specicaons and product informaon in English supersede that which is provided in any other language. For the most recent version of any documentaon, refer to:
www.bannerengineering.com.
QM26 and QMH26 Series Sensors
©Banner Engineering Corp. All rights reserved