Banner SLLE14-280 User manual

EZ-SCREEN®LS Safety Light Screen
Instruction Manual
Original Instructions
179480 Rev. G
3 July 2018
©Banner Engineering Corp. All rights reserved
179480

Contents
1 About This Document .............................................................................................................................................5
1.1 Important . . . Read This Before Proceeding! .....................................................................................................................5
1.2 Use of Warnings and Cautions ...........................................................................................................................................5
1.3 EU Declaration of Conformity (DoC) ..................................................................................................................................5
1.4 Banner Engineering Corp Limited Warranty ......................................................................................................................6
1.5 Contact Us ......................................................................................................................................................................... 6
2 Standards and Regulations ..................................................................................................................................... 8
2.1 Applicable U.S. Standards ................................................................................................................................................. 8
2.2 Applicable OSHA Regulations ............................................................................................................................................8
2.3 International/European Standards ..................................................................................................................................... 9
3 Product Overview .................................................................................................................................................. 10
3.1 Appropriate Applications and Limitations ....................................................................................................................... 11
3.1.1 Appropriate Applications .....................................................................................................................................11
3.1.2 Examples: Inappropriate Applications ................................................................................................................ 11
3.1.3 Control Reliability: Redundancy and Self-Checking ........................................................................................... 12
3.2 Components .....................................................................................................................................................................12
3.2.1 Models ..................................................................................................................................................................12
3.2.2 Replacement Parts ...............................................................................................................................................20
3.3 Operating Features ...........................................................................................................................................................21
3.3.1 Trip Output .......................................................................................................................................................... 21
3.3.2 External Device Monitoring (EDM) ........................................................................................................................21
3.3.3 Fault Output ........................................................................................................................................................ 21
3.3.4 Scan Code Configuration ....................................................................................................................................21
3.3.5 Wiring Options .....................................................................................................................................................21
3.3.6 Cascading ........................................................................................................................................................... 22
3.3.7 EZ-LIGHT®Indication ......................................................................................................................................... 22
3.3.8 Interfacing an E-Stop Button or Interlocking Switch ...........................................................................................23
3.3.9 Remote Fixed Blanking ....................................................................................................................................... 23
3.3.10 Status Indicators ............................................................................................................................................... 23
4 Specifications ....................................................................................................................................................... 24
4.1 General Specifications .................................................................................................................................................... 24
4.2 Receiver Specifications ...................................................................................................................................................25
4.3 Emitter Specifications ..................................................................................................................................................... 25
4.4 Dimensions .......................................................................................................................................................................26
5 Mechanical Installation .......................................................................................................................................... 28
5.1 Mechanical Installation Considerations ...........................................................................................................................28
5.1.1 Calculating the Safety Distance (Minimum Distance) .......................................................................................... 28
5.1.2 Reducing or Eliminating Pass-Through Hazards ................................................................................................ 30
5.1.3 Supplemental Safeguarding ................................................................................................................................31
5.1.4 Reset Switch Location ......................................................................................................................................... 31
5.1.5 Adjacent Reflective Surfaces .............................................................................................................................. 32
5.1.6 Use of Corner Mirrors ..........................................................................................................................................33
5.1.7 Emitter and Receiver Orientation ........................................................................................................................ 34
5.1.8 Installation of Multiple Systems ...........................................................................................................................35
5.2 Mounting System Components ........................................................................................................................................36
5.2.1 Mounting Hardware .............................................................................................................................................36
5.2.2 Mounting the End-Mount Brackets .....................................................................................................................37
5.2.3 Mounting the Center- and Side-Mount Brackets ................................................................................................38
5.2.4 Optional EZLSA-MBK-16 Side-Mount Bracket ....................................................................................................38
5.2.5 Sensor Mounting and Mechanical Alignment ..................................................................................................... 39
5.2.6 Mounting Dimensions ...........................................................................................................................................40
6 Electrical Installation and Testing ..........................................................................................................................42
6.1 Routing Cordsets ............................................................................................................................................................. 42
6.2 Initial Electrical Connections ........................................................................................................................................... 43
6.3 Initial Checkout Procedure ...............................................................................................................................................43
6.3.1 Configuring the System for Initial Checkout ........................................................................................................44
6.3.2 Initial Power-Up ....................................................................................................................................................44
6.3.3 Optical Alignment ................................................................................................................................................44
6.3.4 Optical Alignment Procedure with Mirrors .......................................................................................................... 46
6.3.5 Remote Fixed Blanking ....................................................................................................................................... 46
6.3.6 Trip Test ............................................................................................................................................................... 49
6.4 Electrical Connections to the Guarded Machine .............................................................................................................50
6.4.1 OSSD Output Connections ................................................................................................................................. 50
EZ-SCREEN®LS Safety Light Screen

6.4.2 FSD Interfacing Connections .............................................................................................................................. 51
6.4.3 Machine Primary Control Elements and EDM Input .............................................................................................52
6.4.4 External Device Monitoring ................................................................................................................................. 52
6.4.5 Fault Output ........................................................................................................................................................ 53
6.4.6 Scan Code Select ................................................................................................................................................53
6.4.7 Preparing for System Operation ..........................................................................................................................53
6.4.8 Sensor Interchangeability .....................................................................................................................................53
6.5 Wiring Diagrams ............................................................................................................................................................... 54
6.5.1 Reference Wiring Diagrams .................................................................................................................................54
6.5.2 Generic Wiring Diagram—5-pin and 8-pin Emitter ...............................................................................................54
6.5.3 Generic Wiring Diagram—5-pin Receiver and UM-FA-..A Safety Module ...........................................................55
6.5.4 Generic Wiring Diagram—5-pin Receiver and Safety Module/Controller or Safety PLC/PES ............................56
6.5.5 Generic Wiring Diagram—8-pin Receiver and Redundant FSDs .........................................................................57
6.5.6 Generic Wiring Diagram—8-pin Receiver and IM-T-9A Interface Module ...........................................................58
7 System Operation .................................................................................................................................................59
7.1 Security Protocol .............................................................................................................................................................59
7.2 Status Indicators .............................................................................................................................................................. 59
7.2.1 Emitter ................................................................................................................................................................. 59
7.2.2 Receiver ...............................................................................................................................................................59
7.3 Normal Operation ............................................................................................................................................................61
7.3.1 System Power-Up ............................................................................................................................................... 61
7.3.2 Run Mode .............................................................................................................................................................61
7.4 Periodic Checkout Requirements ................................................................................................................................... 61
8 Checkout Procedures ............................................................................................................................................63
8.1 Schedule of Checkouts ................................................................................................................................................... 63
8.2 Commissioning Checkout ............................................................................................................................................... 63
9 Troubleshooting ....................................................................................................................................................65
9.1 Lockout Conditions .......................................................................................................................................................... 65
9.2 Recovery Procedures ......................................................................................................................................................65
9.2.1 Receiver Error Codes .......................................................................................................................................... 65
9.2.2 Emitter Error Codes .............................................................................................................................................67
9.3 Electrical and Optical Noise ............................................................................................................................................ 67
9.3.1 Checking for Sources of Electrical Noise ............................................................................................................68
9.3.2 Check for Sources of Optical Noise ....................................................................................................................68
10 Maintenance ....................................................................................................................................................... 69
10.1 Cleaning ........................................................................................................................................................................ 69
10.2 Warranty Service ........................................................................................................................................................... 69
10.3 Manufacturing Date .......................................................................................................................................................69
10.4 Disposal ..........................................................................................................................................................................69
11 Cascadeable EZ-SCREEN LS ............................................................................................................................. 70
11.1 Overview of Cascading ................................................................................................................................................. 70
11.1.1 System Components and Specifications ..........................................................................................................71
11.1.2 Receiver Display ................................................................................................................................................71
11.2 Determining Interconnect Cordset Lengths .................................................................................................................. 71
11.3 Response Time for Cascaded Light Screens ................................................................................................................73
11.3.1 Determining System Response Time ................................................................................................................ 73
11.3.2 Individual Response Time and Safety (Minimum) Distance .............................................................................. 74
11.3.3 CSSI Response Time ......................................................................................................................................... 74
11.4 Emergency Stop Buttons in Cascaded Systems ........................................................................................................... 74
11.4.1 E-Stop Switch Requirements (Positive-Opening) ............................................................................................. 75
11.5 Interlock Switches in Cascaded Systems ......................................................................................................................76
11.5.1 Interlock Guarding Requirements ..................................................................................................................... 76
11.5.2 Positive-Opening Interlocking Safety Switches ................................................................................................ 77
11.6 Remote TEACH Fixed Blanking (Wiring) ....................................................................................................................... 78
12 Accessories ......................................................................................................................................................... 80
12.1 Cordsets ........................................................................................................................................................................80
12.1.1 Single-Ended (Machine Interface) Cables ......................................................................................................... 81
12.1.2 Double-Ended (Sensor Interconnect) Cordsets ................................................................................................. 82
12.1.3 Splitter Cordsets ............................................................................................................................................... 85
12.1.4 Bulkhead Connector ..........................................................................................................................................86
12.2 AC Interface Boxes ....................................................................................................................................................... 86
12.3 Universal (Input) Safety Modules ...................................................................................................................................87
12.4 Safety Controllers ..........................................................................................................................................................87
12.5 Muting Module .............................................................................................................................................................. 87
12.6 Interface Modules ...........................................................................................................................................................87
12.7 Contactors ......................................................................................................................................................................88
12.8 Optional Mounting Brackets ...........................................................................................................................................88
12.8.1 ............................................................................................................................................................................88
12.9 Remote Blanking Key Switch Box .................................................................................................................................90
EZ-SCREEN®LS Safety Light Screen

12.10 Alignment Aids ............................................................................................................................................................ 90
12.11 Snap-On Lens Shields ................................................................................................................................................ 90
12.12 Tubular Enclosures ......................................................................................................................................................91
12.13 EZ-SCREEN LS Safety Light Screen in an IP69K Hygienic Housing ...........................................................................91
12.14 EZ-LIGHTS®for EZ-SCREEN®...................................................................................................................................92
12.15 MSM Series Corner Mirrors .........................................................................................................................................94
12.16 SSM Series Corner Mirrors ......................................................................................................................................... 94
12.17 MSA Series Stands ..................................................................................................................................................... 95
13 Glossary ..............................................................................................................................................................96
EZ-SCREEN®LS Safety Light Screen

1 About This Document
1.1 Important . . . Read This Before Proceeding!
It is the responsibility of the machine designer, controls engineer, machine builder, machine operator, and/or maintenance
personnel or electrician to apply and maintain this device in full compliance with all applicable regulations and standards.
The device can provide the required safeguarding function only if it is properly installed, properly operated, and properly
maintained. This manual attempts to provide complete installation, operation, and maintenance instruction.
Reading the
manual in its entirety is highly recommended. Please direct any questions regarding the application or use of the device to
Banner Engineering.
For more information regarding U.S. and international institutions that provide safeguarding application and safeguarding
device performance standards, see Standards and Regulations on page 8.
WARNING: User Responsibility
The user is responsible to:
•Carefully read, understand, and comply with all instructions for this device.
• Perform a risk assessment that includes the specific machine guarding application. Guidance on
a compliant methodology can be found in ISO 12100 or ANSI B11.0.
•Determine what safeguarding devices and methods are appropriate per the results of the risk
assessment and implement per all applicable local, state, and national codes and regulations.
See ISO 13849-1, ANSI B11.19, and/or other appropriate standards.
• Verify that the entire safeguarding system (including input devices, control systems, and output
devices) is properly configured and installed, operational, and working as intended for the
application.
•Periodically re-verify, as needed, that the entire safeguarding system is working as intended for
the application.
Failure to follow any of these responsibilities may potentially create a dangerous condition that could
result in serious injury or death.
1.2 Use of Warnings and Cautions
The precautions and statements used throughout this document are indicated by alert symbols and must be followed for
the safe use of the EZ-SCREEN LS Safety Light Screen. Failure to follow all precautions and alerts may result in unsafe use
or operation. The following signal words and alert symbols are defined as follows:
Signal Word Definition Symbol
WARNING
Warnings refer to potentially hazardous situations which, if not
avoided, could result in serious injury or death.
CAUTION
Cautions refer to potentially hazardous situations which, if not
avoided, could result in minor or moderate injury.
These statements are intended to inform the machine designer and manufacturer, the end user, and maintenance
personnel, how to avoid misapplication and effectively apply the EZ-SCREEN LS Safety Light Screen to meet the various
safeguarding application requirements. These individuals are responsible to read and abide by these statements.
1.3 EU Declaration of Conformity (DoC)
Banner Engineering Corp. herewith declares that the EZ-SCREEN LS is in conformity with the provisions of the Machinery
Directive 2006/42/EC and all essential health and safety requirements have been met.
Representative in EU: Peter Mertens, Managing Director Banner Engineering Europe. Address: Park Lane, Culliganlaan 2F,
1831 Diegem, Belgium.
EZ-SCREEN®LS Safety Light Screen
www.bannerengineering.com - Tel: [phone]

1.4 Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following
the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which,
at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not
cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED
(INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO
EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY
EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT,
WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR
OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any
obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or
improper application or installation of this product or use of the product for personal protection applications when the
product is identified as not intended for such purposes will void the product warranty. Any modifications to this product
without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in
this document are subject to change; Banner reserves the right to modify product specifications or update documentation
at any time. Specifications and product information in English supersede that which is provided in any other language. For
the most recent version of any documentation, refer to:
www.bannerengineering.com .
1.5 Contact Us
Corporate Headquarters
Address:
Banner Engineering Corporate
9714 Tenth Avenue North
Minneapolis, Minnesota 55441, USA
Phone: [phone]
Website:
www.bannerengineering.com
Europe
Address:
Banner Engineering EMEA
Park Lane, Culliganlaan 2F, bus 3
1831 Diegem, Belgium
Phone: [phone]
Website: www.bannerengineering.com
Email: [email protected]
Turkey
Address:
Banner Engineering Elk. San. Ve Tic. Ltd. Şti.
Şerifali Mah. Münevver Sok. Ekomed Plaza No:10 Kat:4
Ümraniye / İstanbul, Türkiye
Phone: [phone]
Website:
www.bannerengineering.com
Email: [email protected]
India
Address:
Banner Engineering India Pune Head Quarters
Office No. 1001, 10th Floor Sai Capital, Opp. ICC Senapati Bapat Road
Pune 411016, India
Phone: [phone]
Website:
www.bannerengineering.com
Email: [email protected]
Mexico
Address:
Banner Engineering de Mexico Monterrey Head Office
Edificio VAO Av. David Alfaro Siqueiros No.103 Col. Valle Oriente C.P.66269
San Pedro Garza Garcia, Nuevo Leon, Mexico
Phone: [phone] or 01 800 BANNERE (toll free)
Website:
www.bannerengineering.com
Email: [email protected]
EZ-SCREEN®LS Safety Light Screen
6 www.bannerengineering.com - Tel: [phone]

Brazil
Address:
Banner do Brasil
Rua Barão de Teffé nº 1000, sala 54
Campos Elíseos, Jundiaí - SP, CEP.: 13208-761, Brasil
Phone: [phone]
Website:
www.bannerengineering.com
Email: [email protected]
China
Address:
Banner Engineering Shanghai Rep Office
Xinlian Scientific Research Building Level 12, Building 2
1535 Hongmei Road, Shanghai 200233, China
Phone: [phone]
Website:
www.bannerengineering.com
Email: [email protected]
Japan
Address:
Banner Engineering Japan
Cent-Urban Building 305 3-23-15 Nishi-Nakajima Yodogawa-Ku
Osaka 532-0011, Japan
Phone: [phone]
Website:
www.bannerengineering.com
Email: [email protected]
Taiwan
Address:
Banner Engineering Taiwan
8F-2, No. 308 Section 1, Neihu Road
Taipei 114, Taiwan
Phone: [phone]
Website:
www.bannerengineering.com
Email: [email protected]
EZ-SCREEN®LS Safety Light Screen
www.bannerengineering.com - Tel: [phone]

2 Standards and Regulations
The list of standards below is included as a convenience for users of this Banner device. Inclusion of the standards below
does not imply that the device complies specifically with any standard, other than those specified in the Specifications
section of this manual.
2.1 Applicable U.S. Standards
ANSI B11.0 Safety of Machinery, General Requirements,
and Risk Assessment
ANSI B11.1 Mechanical Power Presses
ANSI B11.2 Hydraulic Power Presses
ANSI B11.3 Power Press Brakes
ANSI B11.4 Shears
ANSI B11.5 Iron Workers
ANSI B11.6 Lathes
ANSI B11.7 Cold Headers and Cold Formers
ANSI B11.8 Drilling, Milling, and Boring
ANSI B11.9 Grinding Machines
ANSI B11.10 Metal Sawing Machines
ANSI B11.11 Gear Cutting Machines
ANSI B11.12 Roll Forming and Roll Bending Machines
ANSI B11.13 Single- and Multiple-Spindle Automatic Bar
and Chucking Machines
ANSI B11.14 Coil Slitting Machines
ANSI B11.15 Pipe, Tube, and Shape Bending Machines
ANSI B11.16 Metal Powder Compacting Presses
ANSI B11.17 Horizontal Extrusion Presses
ANSI B11.18 Machinery and Machine Systems for the
Processing of Coiled Strip, Sheet, and Plate
ANSI B11.19 Performance Criteria for Safeguarding
ANSI B11.20 Manufacturing Systems
ANSI B11.21 Machine Tools Using Lasers
ANSI B11.22 Numerically Controlled Turning Machines
ANSI B11.23 Machining Centers
ANSI B11.24 Transfer Machines
ANSI/RIA R15.06 Safety Requirements for Industrial Robots
and Robot Systems
ANSI NFPA 79 Electrical Standard for Industrial Machinery
ANSI/PMMI B155.1 Package Machinery and Packaging-
Related Converting Machinery — Safety Requirements
2.2 Applicable OSHA Regulations
OSHA Documents listed are part of: Code of Federal Regulations Title 29, Parts 1900 to 1910
OSHA 29 CFR 1910.212 General Requirements for (Guarding of) All Machines
OSHA 29 CFR 1910.147 The Control of Hazardous Energy (lockout/tagout)
OSHA 29 CFR 1910.217 (Guarding of) Mechanical Power Presses
EZ-SCREEN®LS Safety Light Screen
8 www.bannerengineering.com - Tel: [phone]

2.3 International/European Standards
EN ISO 12100 Safety of Machinery – General Principles for
Design — Risk Assessment and Risk Reduction
ISO 13857 Safety Distances . . . Upper and Lower Limbs
ISO 13850 (EN 418) Emergency Stop Devices, Functional
Aspects – Principles for Design
EN 574 Two-Hand Control Devices – Functional Aspects –
Principles for Design
IEC 62061 Functional Safety of Safety-Related Electrical,
Electronic and Programmable Control Systems
EN ISO 13849-1 Safety-Related Parts of Control Systems
EN 13855 (EN 999) The Positioning of Protective Equipment
in Respect to Approach Speeds of Parts of the Human Body
ISO 14119 (EN 1088) Interlocking Devices Associated with
Guards – Principles for Design and Selection
EN 60204-1 Electrical Equipment of Machines Part 1:
General Requirements
IEC 61496 Electro-sensitive Protection Equipment
IEC 60529 Degrees of Protection Provided by Enclosures
IEC 60947-1 Low Voltage Switchgear – General Rules
IEC 60947-5-1 Low Voltage Switchgear – Electromechanical
Control Circuit Devices
IEC 60947-5-5 Low Voltage Switchgear – Electrical
Emergency Stop Device with Mechanical Latching Function
IEC 61508 Functional Safety of Electrical/Electronic/
Programmable Electronic Safety-Related Systems
EZ-SCREEN®LS Safety Light Screen
www.bannerengineering.com - Tel: [phone]

3 Product Overview
EZ-SCREEN LS Safety Light Screen shown without and with the optional EZLSA-K30LGR EZ-LIGHT
Banner EZ-SCREEN LS is a two-piece (emitter and receiver), redundant, microprocessor-controlled, opposed-mode
optoelectronic "light curtain" or "safety light screen". Models are available in 14 mm, 23 mm, or 40 mm resolution. Up to
four pairs of SLLC.. model emitters and receivers can be cascaded together.
Emitters have a row of synchronized modulated infrared (invisible) light-emitting diodes (LEDs) in a robust, compact metal
housing. Receivers have a corresponding row of synchronized photodetectors. The sensing field created by the emitter and
receiver is called the "defined area"; its width and height are determined by the length of the sensor pair and the distance
between them. The sensing range spans from 100 mm to 12 m (4 in to 39 ft), which decreases if corner mirrors or lens
shields are used.
The length of the sensor pair (housing) is dependent on the model, with lengths available from 280 mm to 1820 mm (11 in to
71.6 in). The end to end sensing design of the EZ-SCREEN LS, also known as "no blind zone" and "no dead zone," allows
mounting with minimal or no gaps in detection when using EZLSA-MBK-12 center-mount or EZLSA-MBK-16 side-mount
brackets.
The EZ-SCREEN LS models have trip output (auto power-up and automatic reset). In typical operation, if any part of an
operator's body (or any opaque object) of more than a pre-determined cross section is detected, the solid-state output
signal switching device (OSSD) safety outputs turn Off. These safety outputs are connected to the guarded machine's final
switching devices (FSDs) that control the machine primary control elements (MPCEs), which immediately stop the motion of
the guarded machine. When the defined area becomes clear, the OSSD outputs are allowed to turn ON.
EZ-SCREEN LS sensors are extensively FMEA (Failure Mode and Effects Analysis) tested to establish an extremely high
degree of confidence that when properly installed, no system component (even if it should ever fail) can cause a failure to
danger. Because of the dual scan technology, EZ-SCREEN LS sensors are also highly immune to EMI, RFI, ambient light,
weld flash, and strobe light.
Eight-conductor EZ-SCREEN LS systems (receivers with 8-pin pigtail QD or flying leads) do not require an external
controller when using the external device monitoring (EDM) function. This function ensures the fault detection capability
required by U.S. Control Reliability and ISO 13849-1 Categories 3 or 4 and PL d or e for controlling final switching devices
(FSDs) or Machine Primary Control Elements (MPCEs).
When configured with a five-conductor hookup, the EZ-SCREEN LS requires a self-checking safety module, safety
controller, or safety PLC/PES that conforms to the level of performance required by the risk assessment. Examples include
the UM-FA-9A/-11A safety module, SC22-3/-3E or XS/SC26-2 safety controller for applications requiring Control Reliability
and/or ISO 13849-1 Categories 3 or 4 and PL d or e.
EZ-SCREEN®LS Safety Light Screen
10 www.bannerengineering.com - Tel: [phone]

Electrical connections (power, ground, inputs and outputs) are made via M12 quick-disconnect cordsets or unique RD
(removable disconnect) cordsets, depending on model. A "System" as referred to in this manual, is defined as an emitter
and its receiver, plus their cabling, or to a cascade of emitters and their receivers and their cabling.
Available features include selectable scan code via hookup, an auxiliary fault output, a recessed exit window, and robust
metal housing and end-caps for industry leading durability.
Additional features on cascade models include automatic configuration of up to four sensor pairs (any length or resolution),
optional EZ-LIGHT indication (integral or remotely located) the ability to interface an E-Stop button or Interlocking switches
(hard contacts), and remote fixed blanking. All models require a supply voltage of +24 V dc ±15%.
Both emitter and receiver feature 7-segment Diagnostic Displays and individual LEDs to provide continuous indication of
operating status, configuration and error conditions. An adhesive Diagnostics label is provided that includes a summary of
the operational and error codes. Active Alignment (Segment) Indicators provide beam block information and easier
installation. See Status Indicators on page 59 for more information.
3.1 Appropriate Applications and Limitations
WARNING: Read this Section Carefully Before Installing the System
If all mounting, installation, interfacing, and checkout procedures are not followed properly, the Banner
device cannot provide the protection for which it was designed. The user is responsible for ensuring that
all local, state, and national laws, rules, codes, or regulations relating to the installation and use of this
control system in any particular application are satisfied. Ensure that all legal requirements have been
met and that all technical installation and maintenance instructions contained in this manual are followed.
The user has the sole responsibility to ensure that this Banner device is installed and interfaced to the
guarded machine by Qualified Persons1, in accordance with this manual and applicable safety
regulations. Failure to follow these instructions could result in serious injury or death.
The EZ-SCREEN LS ability to perform its safeguarding function depends upon the appropriateness of the application and
upon its proper mechanical and electrical installation and interfacing to the guarded machine. If all mounting, installation,
interfacing, and checkout procedures are not followed properly, the EZ-SCREEN LS cannot provide the protection for which
it was designed.
CAUTION: Install System Only on Appropriate Applications
Banner EZ-SCREEN LS is for use only on machinery that can be stopped immediately after a stop signal
is issued at any point in the machine's stroke or cycle, such as part-revolution clutched machines. Under
no circumstances may the EZ-SCREEN LS be used on full-revolution clutched machinery or in unsuitable
applications as those listed. If there is any doubt about whether or not your machinery is compatible with
the EZ-SCREEN LS, contact Banner Engineering.
3.1.1 Appropriate Applications
EZ-SCREEN LS is typically used for, but is not limited to, the following applications:
•Automated production equipment
• Robotic work cells
• Molding and power presses
• Assembly and packaging machines
• Lean manufacturing systems
3.1.2 Examples: Inappropriate Applications
Do not use EZ-SCREEN LS in the following applications:
• With any machine that cannot be stopped immediately after a stop signal is issued, such as single-stroke (or full-
revolution) clutched machinery
• With any machine with inadequate or inconsistent machine response time and stopping performance
• With any machine that ejects materials or component parts through the defined area
•In any environment that is likely to adversely affect photoelectric sensing efficiency. For example, corrosive
chemicals or fluids or unusually severe levels of smoke or dust, if not controlled, may degrade sensing efficiency
1A person who, by possession of a recognized degree or certificate of professional training, or who, by extensive knowledge, training and
experience, has successfully demonstrated the ability to solve problems relating to the subject matter and work.
EZ-SCREEN®LS Safety Light Screen
www.bannerengineering.com - Tel: [phone]

• As a tripping device to initiate or reinitiate machine motion (PSDI applications), unless the machine and its control
system fully comply with the relevant standard or regulation (see OSHA 29CFR1910.217, ANSI/NFPA 79, ANSI
B11.19, ISO 12100, IEC 60204-1, IEC 61496-1, or other appropriate standard)
If an EZ-SCREEN LS is installed for use as a perimeter guard (where a pass-through hazard may exist, see
Reducing or
Eliminating Pass-Through Hazards ), the dangerous machine motion can be initiated by normal means only after the
safeguarded area is clear of individuals and the safety related part of the control system that is providing the latching
function has been manually reset.
3.1.3 Control Reliability: Redundancy and Self-Checking
Redundancy requires that EZ-SCREEN LS circuit components be backed up to the extent that, if the failure of a single
component will prevent effective machine stopping action when needed, that component must have a redundant
counterpart which will perform the same function. The EZ-SCREEN LS is designed with redundant microprocessors.
Redundancy must be maintained whenever the EZ-SCREEN LS is in operation. Because a redundant system is no longer
redundant after a component has failed, EZ-SCREEN LS is designed to monitor itself continuously. A component failure
detected by or within the self-checking system causes a stop signal to be sent to the guarded machine and puts the EZ-
SCREEN LS into a Lockout condition.
A recovery from this type of Lockout condition requires:
• Replacement of the failed component (to restore redundancy)
• The appropriate reset procedure
The Diagnostic Display is used to diagnose causes of a Lockout condition. See
Troubleshooting on page 65.
3.2 Components
3.2.1 Models
An EZ-SCREEN LS “System” refers to a compatible emitter and receiver of equal length and resolution (available in pairs or
separately), including cascaded sensors, and their cordsets. Mounting hardware is included with each emitter and receiver.
Special-purpose mounting brackets both for standalone pairs and for cascades are also available. Depending on the
connection option, interfacing solutions include IM-T-.. modules, redundant positively guided contactors, safety modules/
controllers, and muting modules.
The 13 mm (0.5 in) minimum bend radius for all cordset models accommodates low-clearance installations; cords can exit
to the left, right, or back of the sensor, when mounting. The pigtail QD option is useful for connection to splitter cables or
other QD cordsets.
Defined
Area
Test
RD Cordset
Emitter
Receiver
Status Indicators
visible on sensor face
Figure 1. EZ-SCREEN LS System: Emitter, Receiver, Interconnecting
Cordsets
Euro QD Termination
Pigtail; requires mating QD
cordset for machine
connection
RD to RD cordset options are available
for compact sensor-to-sensor
connections
RD cordset with flying leads
Cable pivots as it exits
housing; bends to fit
against perpendicular
surfaces. R 13 mm [0.5"]
min. bend
Figure 2. EZ-SCREEN LS cordset options
EZ-SCREEN LS Pair model numbers include the following items:
EZ-SCREEN®LS Safety Light Screen
12 www.bannerengineering.com - Tel: [phone]

Qty Description
1 EZ-SCREEN LS Receiver
1 EZ-SCREEN LS Emitter
2 EZLSA-MBK-11 End-Cap Bracket Kit (four brackets)
2 EZLSA-MBK-12 Center-Mount Bracket Kit (two brackets included for models with defined areas ≥ 980 mm)
1 Test Rod (STP-13 for 14 mm models; STP-19 for 23 mm models; or STP-20 for 40 mm models)
1 Literature packet with CD-ROM and Diagnostic Label
Table 1: EZ-SCREEN LS Model Key
Product Family Cascadable System Type Resolution - Defined Area Termination
Options:
SLL
Options:
Blank = No
C= Yes
Options:
E= Emitter only
R= Receiver
only
P= Pair (Emitter
and Receiver)
Options:
14 = 14 mm
23 = 23 mm
40 = 40 mm
-Options:
280 = 280 mm *
350 = 350 mm
420 = 420 mm
490 = 490 mm
560 = 560 mm
630 = 630 mm
700 = 700 mm
770 = 770 mm
840 = 840 mm
910 = 910 mm
980 = 980 mm
1050 = 1050 mm
1120 = 1120 mm
1190 = 1190 mm
1260 = 1260 mm
1330 = 1330 mm
1400 = 1400 mm
1470 = 1470 mm
1540 = 1540 mm
1610 = 1610 mm
1680 = 1680 mm
1750 = 1750 mm
1820 = 1820 mm
Options:
Blank = no pigtail, RD
connection (for
middle/end units in
cascade, or with
RDLS-8..D cordset)
P5 = 300 mm pigtail, 5-
Pin M12 QD (individual
Emitter or Receiver
models)
P55 = 300 mm pigtail, 5-
Pin M12 QD (paired
models)
P8 = 300 mm pigtail, 8-
Pin M12 QD (individual
Emitter or Receiver
models)
P88 = 300 mm pigtail, 8-
Pin M12 QD (paired
models)
Example: SLLCP23-1470P88
* 280 mm defined area not available on cascade systems
To determine the components required for an EZ-SCREEN LS system using the Model Key:
1. Determine if the application calls for a stand-alone (a single, non-cascade emitter and receiver pair) or if a cascade
pair is to be used as a stand-alone and/or with multiple pairs to be ordered are part of a cascaded system.
2. Choose an Emitter (E), a Receiver (R), or a Pair (P).
3. Choose resolution (14, 23, or 40 mm) and defined area.
4. Determine the Machine Interface connection style: 300 mm pigtail QD (5-pin or 8-pin) or a Removable Disconnect
(RD).
5. Model number(s) can be verified in the models tables.
6. See
Cordsets on page 80 for mating cordsets:
• Models with RD connection use either RDLS-8..D, DELS-11..E, DELSE-81D, or DELSE-51D
• Models with P8 (P88) suffix use QDE-8..D, DEE2R-8..D, or CSB-M128..M1281
• Models with P5 (P55) suffix use QDE-5..D, DEE2R-5..D, or CSB-M125..M1251 (MQDEC-406SS is used in
applications where pin 5 is open and ground is via mounting brackets)
7. See
Accessories on page 80 for additional cordsets (for cascade systems), interfacing solutions, and accessories.
EZ-SCREEN®LS Safety Light Screen
www.bannerengineering.com - Tel: [phone]

Ordering Guide
To order an EZ-SCREEN LS system, see
Figure 3 on page 14:
1. Determine if the application calls for a stand-alone (single, non-cascade emitter and receiver pair) or if a cascade
pair is to be used as a stand-alone and/or with multiple pairs to be ordered are part of a cascaded system.
2. Determine the connection style, which is typically dictated by the type of interfacing with the machine's safety-
related control system (300 mm pigtail QD (5-pin or 8-pin) or a Removable Disconnect).
3. Chose the model number(s) from the applicable model number table. Model numbers listed in the tables are RD
connection style model numbers. Add a P5 (or P55) or a P8 (or P88) at the end of the listed model number for a
sensor with a 300 mm (1 ft) pigtail M12/Euro-style QD.
See tables for model number:
Resolution
See Table 10.1.2.1: 14 mm
See Table 10.1.2.2: 23 mm
See Table 10.1.2.3: 40 mm
Connection Style
Add the following suffix to
order a 5-pin pigtail QD:
P5 = Individual sensor
P55 = Pair
Cordset Options (10.2.1):
5-pin cordsets see:
Single-ended QDE-5..D
Double-ended DEE2R-5..D
General accessories (including): See Accessories (10.2)
Mounting brackets (10.2.7),
Splitter Cordsets (10.2.1)
EZ-LIGHT Indicators (10.2.12)
Stands (10.2.15)
Lens shield (10.2.10)
Alignment Aids (10.2.9)
Mirrors (10.2.13)
See tables for model number:
Resolution
Connection Style
P8 = Individual sensor
P88 = Pair
See tables for model number:
Resolution
Connection Style
The model numbers listed
in these tables have RD
connections.
Interfacing Options*:
Cordset Options (10.2.1):
Interfacing Options:
Alternate options:
Cordset Options (10.2.1):
Interfacing Options:
Alternate options:
See the next figure for
Cascade Ordering
System Guide
Stand-alone Cascade
Removable Disconnect (RD)5-Pin Pigtail QD
8-Pin Pigtail QD
Add the following suffix to
order an 8-pin pigtail QD:
8-pin cordsets see:
Single-ended QDE-8..D
Double-ended DEE2R-8..D
8-pin cordsets see:
Single-ended RDLS-8..D
300 mm pigtail DELSE-8..D
UM-FA-..A (10.2.2)
XS/SC26-2.. (10.2.3)
SC22-3.. (10.2.3)
MMD-TA-..B (10.2.4)
IM-T-9A/-11A (10.2.5)
Contactors (10.2.6)
UM-FA-..A (10.2.2)
XS/SC26-2.. (10.2.3)
SC22-3.. (10.2.3)
MMD-TA-..B (10.2.4)
IM-T-9A/-11A (10.2.5)
Contactors (10.2.6)
UM-FA-..A (10.2.2)
XS/SC26-2.. (10.2.3)
SC22-3.. (10.2.3)
MMD-TA-..B (10.2.4)
* 5-pin models must be interfaced with a self-checking safety module, safety controller, or safety PLC/PES that conforms
to the level of performance required by the risk assessment (such as Control Reliability and/or ISO13849-1 Categories 3 or 4 and PL d or e).
See Table 10.1.2.1: 14 mm
See Table 10.1.2.2: 23 mm
See Table 10.1.2.3: 40 mm
See Table 10.1.2.1: 14 mm
See Table 10.1.2.2: 23 mm
See Table 10.1.2.3: 40 mm
Figure 3. Ordering guide for stand-alone systems
EZ-SCREEN®LS Safety Light Screen
14 www.bannerengineering.com - Tel: [phone]

To order a cascade system, see
Figure 4 on page 15:
1. Determine the configuration of the first sensor pair (a stand-alone or the "Master" is connected to the machine
control).
2. Determine the model from the applicable model number table. Model numbers listed in the tables are RD
connection style model numbers. Add a P5 (or P55) or a P8 (or P88) at the end of the listed model number for a
sensor with a 300 mm (1 ft) pigtail M12/Euro-style QD.
3. Determine the remaining sensor pairs (slaves), which will be an RD connection style that uses a DELS-11xxE
interconnection cordset.
See tables for model number:
Resolution
See Table 10.1.2.4: 14 mm
See Table 10.1.2.5: 23 mm
See Table 10.1.2.6: 40 mm
Connection Style
Cordset Options (10.2.1):
See tables for model number:
Resolution
Connection Style
See tables for model number:
Resolution
Connection Style
Interfacing Options*:
Cordset Options (10.2.1):
Interfacing Options:
Cordset Options (10.2.1):
Interfacing Options:
See tables for model number:
Resolution
Connection Style
Resolution
Cordset Options (10.2.1):
RD-to-RD cordset see:
DELS-11xxE
5-Pin Pigtail QD
Sensor Pair #1 (Master/Machine Control)
Sensor Pair #2,
#3, and #4
(Slaves)
Removable Disconnect (RD)
8-Pin Pigtail QD
Add the following suffix to
order a 5-pin pigtail QD:
P5 = Individual sensor
P55 = Pair
P8 = Individual sensor
P88 = Pair
Add the following suffix to
order an 8-pin pigtail QD:
The model numbers listed
in these tables have RD
connections.
The model numbers listed
in these tables have RD
connections.
If a stand-alone (standard)
pair is to be used as as the
end sensor pair, see tables:
See Table 10.1.2.1: 14 mm
See Table 10.1.2.2: 23 mm
See Table 10.1.2.3: 40 mm
Connection Style
The model numbers listed
in these tables have RD
connections.
5-pin cordsets see:
Single-ended QDE-5..D
Double-ended DEE2R-5..D
8-pin cordsets see:
Single-ended QDE-8..D
Double-ended DEE2R-8..D
8-pin cordsets see:
Single-ended RDLS-8..D
300 mm Pigtail DELSE-8..D
UM-FA-..A (10.2.2)
XS/SC26-2.. (10.2.3)
SC22-3.. (10.2.3)
MMD-TA-..B (10.2.4) Alternate options:
IM-T-9A/-11A (10.2.5)
Contactors (10.2.6)
UM-FA-..A (10.2.2)
XS/SC26-2.. (10.2.3)
SC22-3.. (10.2.3)
MMD-TA-..B (10.2.4)
Alternate options:
IM-T-9A/-11A (10.2.5)
Contactors (10.2.6)
UM-FA-..A (10.2.2)
XS/SC26-2.. (10.2.3)
SC22-3.. (10.2.3)
MMD-TA-..B (10.2.4)
Cordsets for optional features,
see:
EZ-LIGHT options: DELSEF-4..D
E-Stop/Interlock: RDLS-8..D
Remote Fix Blank: DELSEF-81D
General accessories (including): See Accessories (10.2)
Mounting brackets (10.2.7),
Splitter Cordsets (10.2.1)
EZ-LIGHT Indicators (10.2.12)
Stands (10.2.15)
Lens shield (10.2.10)
Alignment Aids (10.2.9)
Mirrors (10.2.13)
* 5-pin models must be interfaced with a self-checking safety module, safety controller, or safety PLC/PES that conforms
to the level of performance required by the risk assessment (such as Control Reliability and/or ISO13849-1 Categories 3 or 4 and PL d or e).
See Table 10.1.2.4: 14 mm
See Table 10.1.2.5: 23 mm
See Table 10.1.2.6: 40 mm
See Table 10.1.2.4: 14 mm
See Table 10.1.2.5: 23 mm
See Table 10.1.2.6: 40 mm
See Table 10.1.2.4: 14 mm
See Table 10.1.2.5: 23 mm
See Table 10.1.2.6: 40 mm
Figure 4. Ordering guide for cascading systems
EZ-SCREEN®LS Safety Light Screen
www.bannerengineering.com - Tel: [phone]

Models Tables
As listed in the following tables, the models include an RD connection (for middle/end units in cascade, or with RDLS-8..D
cordset). Add one of these suffixes to the end of the model number(s) listed in the tables below:
•P5: 300 mm (1 ft) PVC cable with a 5-pin M12/Euro-style male quick disconnect (QD) (individual Emitter or Receiver
models)
•P55: 300 mm (1 ft) PVC cable with a 5-pin M12/Euro-style male quick disconnect (QD) (only Paired models)
•P8: 300 mm (1 ft) PVC cable with a 8-pin M12/Euro-style male quick disconnect (QD) (individual Emitter or Receiver
models)
•P88: 300 mm (1 ft) PVC cable with a 8-pin M12/Euro-style male quick disconnect (QD) (only Paired models)
Table 2: 10.1.2.1: EZ-SCREEN LS 14 mm Resolution Models (Standard/Stand-alone with RD connection)
Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLE14-280 SLLR14-280 SLLP14-280 280 mm 11.6 47 160
SLLE14-350 SLLR14-350 SLLP14-350 350 mm 13.3 55 186
SLLE14-420 SLLR14-420 SLLP14-420 420 mm 15.0 63 211
SLLE14-490 SLLR14-490 SLLP14-490 490 mm 16.7 69 237
SLLE14-560 SLLR14-560 SLLP14-560 560 mm 18.4 78 263
SLLE14-630 SLLR14-630 SLLP14-630 630 mm 20.1 86 288
SLLE14-700 SLLR14-700 SLLP14-700 700 mm 21.8 93 314
SLLE14-770 SLLR14-770 SLLP14-770 770 mm 23.5 101 339
SLLE14-840 SLLR14-840 SLLP14-840 840 mm 25.2 108 265
SLLE14-910 SLLR14-910 SLLP14-910 910 mm 26.9 116 391
SLLE14-980 SLLR14-980 SLLP14-980 980 mm 28.6 122 416
SLLE14-1050 SLLR14-1050 SLLP14-1050 1050 mm 30.3 130 442
SLLE14-1120 SLLR14-1120 SLLP14-1120 1120 mm 32.0 137 467
SLLE14-1190 SLLR14-1190 SLLP14-1190 1190 mm 33.7 145 493
SLLE14-1260 SLLR14-1260 SLLP14-1260 1260 mm 35.4 153 518
SLLE14-1330 SLLR14-1330 SLLP14-1330 1330 mm 37.1 160 544
SLLE14-1400 SLLR14-1400 SLLP14-1400 1400 mm 38.7 168 570
SLLE14-1470 SLLR14-1470 SLLP14-1470 1470 mm 40.4 175 595
SLLE14-1540 SLLR14-1540 SLLP14-1540 1540 mm 42.1 183 621
SLLE14-1610 SLLR14-1610 SLLP14-1610 1610 mm 43.8 191 646
SLLE14-1680 SLLR14-1680 SLLP14-1680 1680 mm 45.5 198 672
SLLE14-1750 SLLR14-1750 SLLP14-1750 1750 mm 47.2 206 697
SLLE14-1820 SLLR14-1820 SLLP14-1820 1820 mm 48.9 215 723
Table 3: 10.1.2.2: EZ-SCREEN LS 23 mm Resolution Models (Standard/Stand-alone with RD Connection)
Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLE23-280 SLLR23-280 SLLP23-280 280 mm 8.2 32 110
SLLE23-350 SLLR23-350 SLLP23-350 350 mm 9.1 36 124
EZ-SCREEN®LS Safety Light Screen
16 www.bannerengineering.com - Tel: [phone]

Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLE23-420 SLLR23-420 SLLP23-420 420 mm 9.9 40 135
SLLE23-490 SLLR23-490 SLLP23-490 490 mm 10.8 44 148
SLLE23-560 SLLR23-560 SLLP23-560 560 mm 11.6 47 160
SLLE23-630 SLLR23-630 SLLP23-630 630 mm 12.5 51 175
SLLE23-700 SLLR23-700 SLLP23-700 700 mm 13.3 55 186
SLLE23-770 SLLR23-770 SLLP23-770 770 mm 14.2 59 199
SLLE23-840 SLLR23-840 SLLP23-840 840 mm 15.0 63 211
SLLE23-910 SLLR23-910 SLLP23-910 910 mm 15.9 67 225
SLLE23-980 SLLR23-980 SLLP23-980 980 mm 16.7 69 237
SLLE23-1050 SLLR23-1050 SLLP23-1050 1050 mm 17.5 74 249
SLLE23-1120 SLLR23-1120 SLLP23-1120 1120 mm 18.4 78 269
SLLE23-1190 SLLR23-1190 SLLP23-1190 1190 mm 19.2 82 274
SLLE23-1260 SLLR23-1260 SLLP23-1260 1260 mm 20.1 86 288
SLLE23-1330 SLLR23-1330 SLLP23-1330 1330 mm 20.9 89 300
SLLE23-1400 SLLR23-1400 SLLP23-1400 1400 mm 21.8 93 314
SLLE23-1470 SLLR23-1470 SLLP23-1470 1470 mm 22.6 97 325
SLLE23-1540 SLLR23-1540 SLLP23-1540 1540 mm 23.5 101 339
SLLE23-1610 SLLR23-1610 SLLP23-1610 1610 mm 24.3 104 350
SLLE23-1680 SLLR23-1680 SLLP23-1680 1680 mm 25.2 108 365
SLLE23-1750 SLLR23-1750 SLLP23-1750 1750 mm 26.0 112 376
SLLE23-1820 SLLR23-1820 SLLP23-1820 1820 mm 26.9 116 391
Table 4: 10.1.2.3: EZ-SCREEN LS 40 mm Resolution Models (Standard/Stand-alone with RD Connection)
Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLE40-280 SLLR40-280 SLLP40-280 280 mm 8.2 32 110
SLLE40-350 SLLR40-350 SLLP40-350 350 mm 8.2 32 110
SLLE40-420 SLLR40-420 SLLP40-420 420 mm 8.2 32 110
SLLE40-490 SLLR40-490 SLLP40-490 490 mm 8.2 32 110
SLLE40-560 SLLR40-560 SLLP40-560 560 mm 8.2 32 110
SLLE40-630 SLLR40-630 SLLP40-630 630 mm 8.6 34 117
SLLE40-700 SLLR40-700 SLLP40-700 700 mm 9.1 36 124
SLLE40-770 SLLR40-770 SLLP40-770 770 mm 9.5 38 129
SLLE40-840 SLLR40-840 SLLP40-840 840 mm 9.9 40 135
SLLE40-910 SLLR40-910 SLLP40-910 910 mm 10.3 42 142
SLLE40-980 SLLR40-980 SLLP40-980 980 mm 10.8 44 148
EZ-SCREEN®LS Safety Light Screen
www.bannerengineering.com - Tel: [phone]

Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLE40-1050 SLLR40-1050 SLLP40-1050 1050 mm 11.2 45 155
SLLE40-1120 SLLR40-1120 SLLP40-1120 1120 mm 11.6 47 160
SLLE40-1190 SLLR40-1190 SLLP40-1190 1190 mm 12.0 49 168
SLLE40-1260 SLLR40-1260 SLLP40-1260 1260 mm 12.5 51 175
SLLE40-1330 SLLR40-1330 SLLP40-1330 1330 mm 12.9 53 179
SLLE40-1400 SLLR40-1400 SLLP40-1400 1400 mm 13.3 55 186
SLLE40-1470 SLLR40-1470 SLLP40-1470 1470 mm 13.7 57 193
SLLE40-1540 SLLR40-1540 SLLP40-1540 1540 mm 14.2 59 199
SLLE40-1610 SLLR40-1610 SLLP40-1610 1610 mm 14.6 61 206
SLLE40-1680 SLLR40-1680 SLLP40-1680 1680 mm 15.0 63 211
SLLE40-1750 SLLR40-1750 SLLP40-1750 1750 mm 15.4 65 216
SLLE40-1820 SLLR40-1820 SLLP40-1820 1820 mm 15.9 67 225
Table 5: 10.1.2.4: EZ-SCREEN LS 14 mm Resolution Models (Cascade with RD Connection)
Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLCE14-350 SLLCR14-350 SLLCP14-350 350 mm 13.3 55 186
SLLCE14-420 SLLCR14-420 SLLCP14-420 420 mm 15.0 63 211
SLLCE14-490 SLLCR14-490 SLLCP14-490 490 mm 16.7 69 237
SLLCE14-560 SLLCR14-560 SLLCP14-560 560 mm 18.4 78 263
SLLCE14-630 SLLCR14-630 SLLCP14-630 630 mm 20.1 86 288
SLLCE14-700 SLLCR14-700 SLLCP14-700 700 mm 21.8 93 314
SLLCE14-770 SLLCR14-770 SLLCP14-770 770 mm 23.5 101 339
SLLCE14-840 SLLCR14-840 SLLCP14-840 840 mm 25.2 108 365
SLLCE14-910 SLLCR14-910 SLLCP14-910 910 mm 26.9 116 391
SLLCE14-980 SLLCR14-980 SLLCP14-980 980 mm 28.6 122 416
SLLCE14-1050 SLLCR14-1050 SLLCP14-1050 1050 mm 30.3 130 442
SLLCE14-1120 SLLCR14-1120 SLLCP14-1120 1120 mm 32.0 137 467
SLLCE14-1190 SLLCR14-1190 SLLCP14-1190 1190 mm 33.7 145 493
SLLCE14-1260 SLLCR14-1260 SLLCP14-1260 1260 mm 35.4 153 518
SLLCE14-1330 SLLCR14-1330 SLLCP14-1330 1330 mm 37.1 160 544
SLLCE14-1400 SLLCR14-1400 SLLCP14-1400 1400 mm 38.7 168 570
SLLCE14-1470 SLLCR14-1470 SLLCP14-1470 1470 mm 40.4 175 595
SLLCE14-1540 SLLCR14-1540 SLLCP14-1540 1540 mm 42.1 183 621
SLLCE14-1610 SLLCR14-1610 SLLCP14-1610 1610 mm 43.8 191 646
SLLCE14-1680 SLLCR14-1680 SLLCP14-1680 1680 mm 45.5 198 672
EZ-SCREEN®LS Safety Light Screen
18 www.bannerengineering.com - Tel: [phone]

Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLCE14-1750 SLLCR14-1750 SLLCP14-1750 1750 mm 47.2 206 697
SLLCE14-1820 SLLCR14-1820 SLLCP14-1820 1820 mm 48.9 215 723
Table 6: 10.1.2.5: EZ-SCREEN LS 23 mm Resolution Models (Cascade with RD Connection)
Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLCE23-350 SLLCR23-350 SLLCP23-350 350 mm 9.1 36 124
SLLCE23-420 SLLCR23-420 SLLCP23-420 420 mm 9.9 40 135
SLLCE23-490 SLLCR23-490 SLLCP23-490 490 mm 10.8 44 148
SLLCE23-560 SLLCR23-560 SLLCP23-560 560 mm 11.6 47 160
SLLCE23-630 SLLCR23-630 SLLCP23-630 630 mm 12.5 51 175
SLLCE23-700 SLLCR23-700 SLLCP23-700 700 mm 13.3 55 186
SLLCE23-770 SLLCR23-770 SLLCP23-770 770 mm 14.2 59 199
SLLCE23-840 SLLCR23-840 SLLCP23-840 840 mm 15.0 63 211
SLLCE23-910 SLLCR23-910 SLLCP23-910 910 mm 15.9 67 225
SLLCE23-980 SLLCR23-980 SLLCP23-980 980 mm 16.7 69 237
SLLCE23-1050 SLLCR23-1050 SLLCP23-1050 1050 mm 17.5 74 249
SLLCE23-1120 SLLCR23-1120 SLLCP23-1120 1120 mm 18.4 78 269
SLLCE23-1190 SLLCR23-1190 SLLCP23-1190 1190 mm 19.2 82 274
SLLCE23-1260 SLLCR23-1260 SLLCP23-1260 1260 mm 20.1 86 288
SLLCE23-1330 SLLCR23-1330 SLLCP23-1330 1330 mm 20.9 89 300
SLLCE23-1400 SLLCR23-1400 SLLCP23-1400 1400 mm 21.8 93 314
SLLCE23-1470 SLLCR23-1470 SLLCP23-1470 1470 mm 22.6 97 325
SLLCE23-1540 SLLCR23-1540 SLLCP23-1540 1540 mm 23.5 101 339
SLLCE23-1610 SLLCR23-1610 SLLCP23-1610 1610 mm 24.3 104 350
SLLCE23-1680 SLLCR23-1680 SLLCP23-1680 1680 mm 25.2 108 365
SLLCE23-1750 SLLCR23-1750 SLLCP23-1750 1750 mm 26.0 112 376
SLLCE23-1820 SLLCR23-1820 SLLCP23-1820 1820 mm 26.9 116 391
Table 7: 10.1.2.6: EZ-SCREEN LS 40 mm Resolution Models (Cascade with RD Connection)
Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLCE40-350 SLLCR40-350 SLLCP40-350 350 mm 8.2 32 110
SLLCE40-420 SLLCR40-420 SLLCP40-420 420 mm 8.2 32 110
SLLCE40-490 SLLCR40-490 SLLCP40-490 490 mm 8.2 32 110
EZ-SCREEN®LS Safety Light Screen
www.bannerengineering.com - Tel: [phone]

Emitter Receiver Pair Defined Area Response Time,
Tr (ms)
Recovery Time, Typ, OSSDs OFF
to ON (ms)
Non-sync beam
blocked
All beams
blocked
SLLCE40-560 SLLCR40-560 SLLCP40-560 560 mm 8.2 32 110
SLLCE40-630 SLLCR40-630 SLLCP40-630 630 mm 8.6 34 117
SLLCE40-700 SLLCR40-700 SLLCP40-700 700 mm 9.1 36 124
SLLCE40-770 SLLCR40-770 SLLCP40-770 770 mm 9.5 38 129
SLLCE40-840 SLLCR40-840 SLLCP40-840 840 mm 9.9 40 135
SLLCE40-910 SLLCR40-910 SLLCP40-910 910 mm 10.3 42 142
SLLCE40-980 SLLCR40-980 SLLCP40-980 980 mm 10.8 44 148
SLLCE40-1050 SLLCR40-1050 SLLCP40-1050 1050 mm 11.2 45 155
SLLCE40-1120 SLLCR40-1120 SLLCP40-1120 1120 mm 11.6 47 160
SLLCE40-1190 SLLCR40-1190 SLLCP40-1190 1190 mm 12.0 49 168
SLLCE40-1260 SLLCR40-1260 SLLCP40-1260 1260 mm 12.5 51 175
SLLCE40-1330 SLLCR40-1330 SLLCP40-1330 1330 mm 12.9 53 179
SLLCE40-1400 SLLCR40-1400 SLLCP40-1400 1400 mm 13.3 55 186
SLLCE40-1470 SLLCR40-1470 SLLCP40-1470 1470 mm 13.7 57 193
SLLCE40-1540 SLLCR40-1540 SLLCP40-1540 1540 mm 14.2 59 199
SLLCE40-1610 SLLCR40-1610 SLLCP40-1610 1610 mm 14.6 61 206
SLLCE40-1680 SLLCR40-1680 SLLCP40-1680 1680 mm 15.0 63 211
SLLCE40-1750 SLLCR40-1750 SLLCP40-1750 1750 mm 15.4 65 216
SLLCE40-1820 SLLCR40-1820 SLLCP40-1820 1820 mm 15.9 67 225
3.2.2 Replacement Parts
Model Description
STP-13 14 mm test piece (14 mm resolution systems)
STP-19 23 mm test piece (23 mm resolution systems)
STP-20 40 mm test piece (40 mm resolution systems)
EZLSA-RTP-1 Terminator plug, for SLLCR… receivers (included with receivers)
EZLSA-DP-1 Dust plug, for SLLCE… emitters (included with emitters)
DELSE-51D Replacement for 300 mm pigtail, as shipped with standard 5-pin pigtail QD models; 5-conductor cable, 0.3 m (1 ft) long
DELSE-81D Replacement for 300 mm pigtail, as shipped with standard 8-pin pigtail QD models; 8-conductor cable, 0.3 m (1 ft) long
EZLSA-MBK-11 End-cap bracket kit (includes 2 end brackets and hardware); 360° sensor rotation possible (± 23° increments); 8 ga (4.0 mm)
steel, black zinc plated; Includes 2 brackets and hardware
EZLSA-MBK-12 Center-mount bracket kit (includes 1 bracket and hardware); +15°/ −30° sensor rotation; 8 ga (4.0 mm) steel, black zinc
plated; die-cast zinc clamp. Includes 1 bracket and hardware
SMA-MBK-1 SSM mirror bracket kit. Includes 2 replacement brackets for one mirror
179480 EZ-SCREEN LS Instruction Manual
89919 CD ROM EZ-SCREEN LS
EZ-SCREEN®LS Safety Light Screen
20 www.bannerengineering.com - Tel: [phone]