Bartscher 165.510 User manual

FE - 0
8
FRYERS
Date:
10 / 2010
INSTRUCTIONS FOR INSTALLATION AND USE
INSTRUCTIONS FOR INSTALLATION AND USE
FRYER
165.510

2
CO
NTENT
DE
C
LARATI
O
N
O
F A
S
TANDARD
S
CO
NF
O
RMITY
3
IN
S
TR
UC
TI
O
N F
O
R
US
E
5
C
LEANIN
G
AND MAINTENAN
C
E
6

3
DE
C
LARATI
O
N
O
F A
S
TANDARD
S
CO
NF
O
RMITY
The producer con
fi
rms that the devices a
g
ree with
C
EE 90
/
396 standards, rule nr. 22
/
1997 sb. and with relevant
g
overment orders. Instalation must be done with respect to valid standards. Attention, the producer re
f
uses
an
y
responsibilit
y
in case o
f
direct or indirect dama
g
es which are caused due to wron
g
instalation, incorrect
intervention or modi
fi
cation, insu
ffi
cient maintenance, incorrect use and also possibl
y
caused b
y
other reasons
p
resented b
y
items in sale conditions. This appliance is set onl
y
f
or skilled use and must be operated b
y
quali
fi
ed
p
ersons onl
y
. Parts set and secured b
y
the producer or accredited person must not be rebuilt b
y
user
.
T
E
C
HNI
C
AL DATA
L
abel with technical data is placed on the back side o
f
the device.
S
tud
y
the electrical dia
g
ram o
f
connection and
all
f
ollowin
g
in
f
ormation be
f
ore instalation.
PACKING AND DEVICE CHECK
The device leaves our stocks properly packed with appropriate symbols and labels. There are also appropriate
instructions for use. In case the packing shows bad handling or damage, it must be reclaimed at transporter
immediately by writing and signing of a damage protocol. Important notice
• this instructing guide must be read properly and carefuly because it contains important information about safety
elements, instalation, use
• these recommendations refer to this product
• this product corresponds with valid standards
• this guide must be properly deposited for future use
• keep the children away from manipulation with the product
• when selling or moving the product to another place it is necessary to make yourself sure that the staff or the
professional service has got acquainted with control and instalation instructions from enclosed guide
• only authorised person can operate the product
• can be use only for frying food
• it cannot be switched on without supervision
• we recommend to have the product checked by proffesional service min. once a year
• only original spare parts can be used for repairs
• the product cannot be cleaned by the water jet or pressure shower
• by damage or break down disconnect all the feeders (water, gas, electricity) and call proffesional service
• producer refuses any responsibility in case of damages caused by wrong instalation, by disobserving of above
mentioned recom mendations or by other use etc.
MODEL VOLTAGE
(V/HZ) WATTAGE (W) DIMENSIONS (CM)
DIMENSIONS
OF BASKET (MM)
FE - 08 230 / 50 3 400 21 x 52 x 30 150 x 320 x 120

4
T
E
C
HNI
C
AL IN
S
TR
UC
TI
O
N
S
F
O
R IN
S
TALATI
O
N AND RE
GU
LATI
O
N
C
an be used
O
NLY b
y
specialized technicians. followin
g
instructions appl
y
to the technician specialized in
i
nsta
l
at
i
on to
d
o a
ll
t
h
e operat
i
ons
i
n t
h
e most correct wa
y
an
d
accor
di
n
g
to t
h
e va
lid
stan
d
ar
d
s
.
Important:
An
y
activit
y
connected with re
g
ulation etc. must be done onl
y
when the device is disconnected from electricit
y
.
If it is necessar
y
to have the device connected to the electricit
y
(
durin
g
repairs
)
y
ou must be ver
y
careful
.
PLA
C
EMENT
The device must be instalated in well ventilated room what is necessar
y
for re
g
ulation of the function of the device
(
technician must
g
o b
y
valid standard
(
ČSN....
)
. If the device is situated close to the wall or if it is in contact with
the furniture walls, these walls must resist the temperatures ran
g
in
g
to 60°C. Instalation, settin
g
, puttin
g
into
operation must be done b
y
qualified person who is competent for this and accordin
g
to the valid standards.
Wrap up the device and check whether it was not dama
g
ed durin
g
transport. Settle the device on horizontal
surface
(
max imbalance 2°
)
.Settle the device under the fumehood to eliminate water steam and bad smell.The
device can be instalated separatel
y
or in a set with devices of our production. Min. distance 10 cm from other
sub
j
ects must be kept.It is also necessar
y
to prevent our product from contact with combustible materials. In this
c
ase
y
ou must make correspondin
g
chan
g
es to secure heat izolation of combustible parts. Safet
y
measures
from the standpoint of the fire protection accordin
g
to ČSN 061008čl. 21
:
S
AFETYMEA
SU
RE
S
FR
O
MTHE
S
TANDP
O
INT
O
FTHEFIREPR
O
TE
C
TI
O
NA
CCO
RDIN
G
TO
ČS
N
06
1
008
Č
L. 21
•
onl
y
adults can operate the devic
e
•
device must be safel
y
used in common surroundin
g
s accordin
g
to ČSN 332000-
1
•
device must be placed so as to stand or han
g
on the noncombustible surface. No sub
j
ects from combustible
m
aterials can be placed directl
y
on the device or in distance which is shorter than safet
y
distance
(
the shortest
distance is 10 cm
)
.
•
safet
y
distances from various materials of different de
g
ree of combustion and information about the de
g
ree o
f
c
omb. of common buildin
g
materials - see chart
:
C
hart:
C
ombustion de
g
ree of buildin
g
materials classified accordin
g
to the combustion de
g
ree of materials and products
(
ČSN 730823
)
A noncombustible
g
ranit, sandstone, concretes,bricks, ceramic wallfacin
g
tiles, plaster
B
uneasil
y
combustible akumine, heraklite, lihnos, itaver
e
C
1 hardl
y
combustible leaf
y
wood, pl
y
wood, sirkoklit, rare paper formica
C
2 middle combustible fibreboards, solodure, cork boards, rubber,floor-coverin
g
s
C
3 easil
y
combustible wood-fibreboards, pol
y
st
y
rene,pol
y
urethane, PV
C
D
evices must be instalated in a safe wa
y
. When instalin
g
y
ou must respect correspondin
g
pro
j
ect, safet
y
and
hyg
ienic orders accordin
g
to
:
•
ČSN 061008 fire
p
rotection of local devices and sources of hea
t
•
ČSN 332000 surroundin
g
for electric devices
CO
NNE
C
TI
O
N
O
F THE ELE
C
TRI
C
C
ABLE T
O
THE ELE
C
TRI
C
ITY
Instalation of electric feeder - This feeder must be separetel
y
protected b
y
a safet
y
fuse accordin
g
to the specific
electric stream which depends on the watta
g
e of the instaled device. Check the watta
g
e on the label at the back
of the device. Connect the device directl
y
to the electricit
y
but
y
ou must put the switch between the device and
electric net. The switch must be placed in min. distance 3 mm between the particular contacts accordin
g
to the
standards and loadin
g
. The feeder of
g
roundin
g
(y
ellow-
g
reen
)
cannot be interrupted b
y
this switch. In ever
y
c
ase feedin
g
cable must be placed so that no point of the cable will reach the temperature which is 50°C hi
g
her
than the temperature of the surroundin
g
. Before connectin
g
the device check that
:

5
•
safet
y
fuse of the feeder and inner mains can stand the loadin
g
of the device
(
see label of the matrix
)
•
mains are equipped with effective
g
roundin
g
accordin
g
to standards
(
ČSN
)
and conditions
g
iven b
y
law
•
soc
k
e
t
o
r
s
wit
c
h
o
f th
e
f
eed
i
s
w
e
ll
access
i
b
l
e
fr
o
m
de
vi
ce
We refuse an
y
responsibilit
y
in case of not respectin
g
above mentioned rules. Before the first use it is necessar
y
to remove all the protection foil and to clean the device - see chapter „cleanin
g
and maintenance“.
M
aintenance: We recommend to have the device checked once a
y
ear b
y
the proffesional service.
O
nl
y
qualified
or com
p
etent
p
ersons can do interventions in the
p
roduct
.
I
N
S
TR
UC
TI
O
N F
O
R
USE
Attention!Before the first use of the device
y
ou must remove protection foil from all surfaces and wash the
device with water with deter
g
ent. Than splash it with clean water. Use the device under supervision. Never use
the device without oil or if the level of the oil is lower then min. line - dan
g
er of fire. If the oil is dirt
y
or
y
ou use
the oil lon
g
er time it ma
y
cause boilin
g
over
.
D
o not fr
y
more then 1 k
g
of food to
g
ether in one bath
.
F
ill the device with fr
y
in
g
oil not hi
g
her than the line on the side. Switch on with main switch
(
B
)
turn the knob
(
E
)
to required position between 90°C - 180°C. Pilot lamps
(
C
)
and
(
D
)
will li
g
ht. Pilot lamp
(
C
)
li
g
hts when the
device is in electricit
y
. Pilot lamp
(
D
)
li
g
hts when the thermo spirals are on. Pilot lamp
(
D
)
g
oes out when the
device reaches required temperature. Switch the device off b
y
turnin
g
the knob
(
E
)
into position „0“ and switch
over the switch
(
B
)
into position „0“.
C
omments and recommendatio
n
Y
ou must alwa
y
s check the level of oil, never use the device without oil. Use the device onl
y
under supervision
.
C
B
E
D

6
CLEANING AND MAINTENANCE
ATTENTION! The device cannot be cleaned by direct or pressure water. Clean it daily. Daily maintenance keeps
longer useful life and efficiency of the device. Before cleaning make sure to have disconnected the device from
electricity. Always switch off the main feeder to the device. Stainless parts wash with moist cleaning cloth and
detergent without groove parts than dry it by the cloth - mainly around the regulation knob, main switch, cable
bushing, feeding cable, microswitch and fit-on listel. Do not use abrasive and corrosive detergents. How to clean
heating elements - take out the box with heating elements. Clean the heating elements only with moist cloth.
How to discharge the oil - take out the bown with the aid of handles on the sides. Do this only when the oil is cold.
You can wash the bowl in the dishwasher. After washing it dry it with cloth and fill it with filtrated or new oil.
Model FE-10T/1010T: User must have convenient bowl for discharging the bath.This bowl must be made from
heat-resistant material. Put the bowl in the safe place to prevent discharging oil from splashing. Splashing can
cause the danger. Put on the discharging pipe, open the safery catch by turning it up and turn the lever into
position marked as opening of the cock. Discharge the bath only when the oil is cold.
WHAT TO DO IN CASE OF BREAK-DOWN
Switch off the electric feeder and call seller´s proffesional service.
INDICATION
Guarentee does not cover all consumption parts succumable to common wear (rubber seals, bulbs, glas and
plastic parts etc.). The guarantee does not refer to the devices which were not instaled in correspondance with
instructions - by qualified worker, in confirmity with standards and when somebody handled incompetently the
device (interventions into inner equipment) or the device was operated by nonqualified staff or at variance with
instructions for use. Guarantee does not also cover the damages caused due to influance of nature or other
outer intervention.