Baumatic BSPO610 User manual

Simplified Instructions for Use
BSPO610

Ok
1 3 42
3
Control Panel
1Function selector.
2Door lock. When this pilot light is on, it
indicates that the oven door is locked and
cannot be opened.
3Electronic clock.
4Temperature selector.
Switch off oven
Conventional
It is used for sponges and cakes where the
heat received must be uniform to achieve a
spongy texture.
Conventional with fan
Appropriate for roasts and cakes. The fan
spreads the heat uniformly inside the oven.
Grill
For preparing dishes with superficial roasting.
It allows the outer layer to be browned without
affecting the inside of the food. Ideal for flat
food, such as steaks, ribs, fish, toast.
MaxiGrill
Allows greater surfaces to be prepared, than
with the grill, together with higher power redu-
cing the time required for browning of the food.
MaxiGrill with fan
Allows uniform roasting at the same time as
surface browning. Ideal for grills. Special for
large volume pieces, such as poultry, game,
etc. It is recommended to put the item on a
rack with a tray beneath to collect the stock
and juices.
Caution
While using the Grill, MaxiGrill or MaxiGrill with
fan, the door must be kept closed.
Turbo
The fan distributes the heat coming from an
element located at the back of the oven. As a
result of the evenly distributed temperature,
food can be cooked on two levels at the same
time.
Lower Element with Turbo
Ideal for baking pizzas, pies, and fruit tarts or
sponges.
Oven Functions

4
Caution
The electronic clock features Touch-Control
technology. To operate, simply touch the glass
control symbols with your fingertip.
The touch control sensitivity continuously
adapts to ambient conditions. Make sure the
glass surface of the control panel is clean and
free of obstacles when plugging in the oven.
If the clock does not respond correctly when
you touch the glass, unplug the oven for a few
seconds and then plug it in again. Doing this
causes the sensors to adjust automatically so
that they will react once more to fingertip con-
trol.
Setting the time on the Electronic Clock
When the oven is connected to the power sup-
ply, the indication 00:00 flash on the display.
Press or to set the time on the clock. The
clock beeps twice to confirm the selected time.
If you wish to modify the time, press or
until the current time flash on the screen.
Press OK. Then press or to modify the
time. The clock beeps twice to confirm the
modification.
Manual Operation
The oven is ready to be used when the clock
has been set. Select a cooking function and a
temperature.
When you begin cooking, symbol lights up
to indicate that the oven is heating the con-
tents; the symbol goes out when the select-
ed temperature is reached.
Set the controls to to turn the oven off.
Functions of the Electronic Clock
Alarm: Creates an alarm signal when the peri-
od of time finishes; the oven does not need to
be in use in order to use this function.
Cooking Time: To cook for a selected length
of time; the oven turns itself off automatically
when the time finishes.
End Cooking Time: To cook until a set time;
the oven turns itself off automatically when
the time finishes.
Using the Oven
Lower element
Heats only from beneath. Suitable for heating
dishes and raising pastry and similar.
Defrosting
This cooking mode is suitable for gently defros-
ting of food. In special food to be consumed
unwarmed, e.g.: cream, custard, pastry, tarts,
cakes, fruit, etc.
Pyrolytic Function
This programme allows you to carry out a
pyrolytic cleaning cycle which involves the oxi-
disation and carbonisation of grease accumu-
lated during cooking, through the high tempe-
ratures that are reached inside the oven.
During the cleaning cycle the light inside the
oven will remain off.
NB
The light remains on through all cooking func-
tions except the pyrolytic function.

5
Cooking time and End Cooking Time: To cook
for a selected length of time and end at a set
time. When this function is set, the oven
comes on automatically at the time required in
order to cook for the set length of time
(Cooking time) and end automatically at the
indicated time (End Cooking Time)
Programming the Alarm
1Press until symbol lights up. Press
OK.
2Set the period of time after which you wish
the alarm to sound by pressing or .
3The clock beeps twice, the current time is
displayed and symbol lights up perma-
nently to indicate that the alarm has been
set.
4When the set period of time comes to an
end, the alarm sounds and symbol starts
to flash.
5Press any button to stop the alarm; symbol
goes out.
You can consult the remaining time at any
moment by pressing or until symbol
flashes and then pressing OK. You can also
modify the set time at this point by pressing
or . The clock beeps twice to confirm the
change.
If you wish the remaining time to be displayed
until the end of the set period of time, press
or until symbol flashes and then
press OK and keep it pressed in. Symbol
flashes. Keep OK pressed in again to return to
the real time.
Setting the Cooking Time
1Press or until symbol lights up.
Press OK.
2Select the period of time you wish to cook
for by pressing or .
3The clock beeps twice, the current time is
displayed and symbol lights up perma-
nently to indicate that the oven will turn
itself off automatically.
4Select a cooking function and temperature.
5When the cooking time comes to an end, the
oven turns itself off, the alarm sounds and
symbol flashes.
6Press any button to stop the alarm and turn
the oven back on again.
7Set the controls to to turn the oven off.
You can consult the remaining cooking time at
any moment by pressing or until symbol
flashes and then pressing OK. You can
also modify the set time at this point by press-
ing or . The clock beeps twice to confirm
the change.
If you wish the remaining time to be displayed
until the end of the set period of time, press
or until symbol flashes and then
press OK and keep it pressed in. Symbol
flashes. Keep OK pressed in again to return to
the real time.
Setting the End Cooking Time
1Press or until symbol lights up.
Press OK.
2Select the time you wish the cooking
process to finish at by pressing or .
3The clock beeps twice, the current time is
displayed and symbol lights up perma-
nently to indicate that the oven will turn
itself off automatically.
4Select a cooking function and temperature.
5When the set time is reached, the oven
turns itself off, the alarm sounds and sym-
bol flashes.
6Press any button to stop the alarm and turn
the oven back on again.
7Set the controls to to turn the oven off.
You can consult the end cooking time at any
moment by pressing or until symbol
flashes and then pressing OK. You can also
modify the end cooking time at this point by
pressing or . The clock beeps twice to
confirm the change.

6
This function can be used even when you are
already using the oven. To do this, follow the
instructions indicated above except point
number 4.
Setting the Cooking Time and the End
Cooking Time
1Press or until symbol lights up.
Press OK.
2Select the period of time you wish to cook
for by pressing or .
3The clock beeps twice, the current time is
displayed and symbol lights up per-
manently.
4Press or until symbol lights up.
Press OK.
5Select the time you wish the cooking
process to finish at by pressing or .
6The clock beeps twice, the current time is
displayed and symbol lights up per-
manently.
7Select a cooking function and tempera-
ture.
8The oven remains off with symbols
and lit up. Your oven is set.
9When the time to start cooking is reached,
the oven starts up and cooks for the set
period of time.
10 When the set end cooking time is reached,
the oven turns itself off, the alarm sounds
and symbols and flash.
11 Press any button to stop the alarm and
turn the oven back on again.
12 Set the controls to to turn the oven off.
You can modify the end cooking time by press-
ing or until symbol lights up and
then pressing OK. You can now modify the end
cooking time by pressing or . The clock
beeps twice to confirm the change.
Important
In the event of a power cut, all the electronic
clock settings are deleted and the indication
00:00 flashes on the display. It is necessary
to set the time and programme the clock
again.

7
Follow the instructions below to complete a
pyrolytic cleaning cycle:
IMPORTANT: Remove all accessories (trays,
grills, tray side supports, tele-
scopic guide rails) from inside the oven.
1. Ensure all major food residues are remo-
ved from the oven and thoroughly clean the
inner door glass.
2. Turn the cooking control dial to the Pyrolytic
position . You will hear a beep which
confirms this function has been chosen.
3. You will then see a P (pyrolytic programme)
on the timer display together and the
symbol will flash.
4. Press the + or – sensors to select one of
the pyrolytic programmes (P1, P2 or P3).
P1: Minimum programme (lasts 1 hour).
P2: Standard programme (lasts 1.5 hours).
P3: Maximum programme (lasts 2 hours).
5. After a couple of seconds, you will hear 2
beeps confirming the pyrolytic programme
chosen.
6. After a short time, the pilot light will turn
on and the oven door will be locked.
7. The oven will start to heat up and the
symbol will appear permanently. The
timer display will show the time remaining
until the end of the programme.
IMPORTANT: At this point, the oven is pro-
grammed and the pyrolitic cleaning cycle is
underway. During the cycle, none of the oven
timer functions may be chosen. Do not try to
open the oven door as this may interrupt the
cleaning process.
8. When the pyrolytic cleaning cycle has
finished, an alarm will sound and the
symbol will flash.
9. Press any of the timer keys to turn the
alarm off. The symbol will disappear.
10. Turn the cooking control dial to the posi-
tion .
11. Although the oven’s heating process has
ended, it is extremely hot and cannot be
used. The cooling motor will operate until
the oven cools down and the pilot light
will remain on.
IMPORTANT
The cooling process may last up to 2 hours
because of the high temperatures inside the
oven.
12. Once pilot light has turned off, you will
soon be able to open the oven door.
IMPORTANT
To open the door (pilot light on), the control
dial must be in position . If you did not
follow step 10, set the control dial to position
and wait a few minutes until the door
unlocks and the pilot light turns off.
13. Open the oven door and wipe the inside
with a damp cloth, cleaning up the ash
from the cleaning cycle. Hard-to-reach
areas in the oven will need to be cleaned
with a non-metallic fibre scourer.
14. Once the oven is clean, remember to
replace the supports and accessories.
15. The oven is now ready to be used.
IMPORTANT: If any incidents are detected in
the programming and operating of this func-
tion, consult the section “Incidents while
Operating the Pyrolytic Function”.
PROGRAMMING AND OPERATING THE PYROLYTIC FUNCTION

8
CANCELLING THE PYROLYTIC CYCLE
Pyrolytic is an automatic function and there
fore can only be activated from the timer pro-
gramme. To cancel a cleaning cycle it is neces-
sary to reset the oven, following the instruc-
tions below:
1Set the function control at and wait for
1 minute.
2Unlock the oven door.
1 Set the function control at and wait for
1 minute. The oven will no longer heat up.
2 Unlock the oven door. To cancel the clean-
ing cycle, the oven door must be unlocked.
To do so, consider the following:
a) Unlocking the door 45 minutes after
the cleaning cycle. If the oven has been
operating for more than 45 minutes, the
door will unlock automatically once the
oven has cooled down to the safe tem-
perature. Then, pilot light will switch
off.
b) Unlocking the door in the first 45 min-
utes (at a low temperature). Within the
first 45 minutes the oven door will
unlock automatically. Follow the instruc-
tions below:
1Turn the control dial to position .
2Wait for approximately 1 minute.
3Turn the control dial to position .
4Approximately, 1 minute later pilot
light will turn off and the oven door
can be opened.

9
INCIDENTS WHEN OPERATING THE PYROLYTIC FUNCTION
INCIDENT CAUSE SOLUTION
My accessories and shelf
supports are damaged.
You have not removed the
accessories and supports during
the pyrolytic cleaning cycle.
You must replace them and
remove them in later cleaning
cycles.
The enamel colour has
changed and stains have
appeared.
The chemical composition of
some foodstuffs may cause
changes in the enamel.
This is normal and does not
damage the properties of the
enamel.
The oven door is locked, pilot
light is lit up but the oven
is not hot.
You have turned the control
dial to position and no
other additional operation has
been performed.
Switch off the oven and follow
the instructions to unlock the
door in the first 45 minutes at
a low temperature.
Next, select the pyrolytic
function, carefully following the
instructions.
I have turned the control dial
to position and selected
a pyrolytic programme (P1, P2
or P3) but the pilot light has
not lit up and the oven is not
heating up.
The oven door has not been
closed properly so it cannot
be locked automatically.
Check the door and make
sure that it is closed properly.
I have turned the control dial
to position and selected
a pyrolytic programme (P1, P2
or P3) but the pilot light
has not lit up and the oven is
not heating up.
The door switch is not working
even though the door is
properly closed.
Call Technical Assistance
Service as there is a fault in
the door switch.
I have programmed the
pyrolytic function, the oven is
working properly but pilot light
is not lit up.
Pilot light does not work
properly.
Call the Technical Assistance
Service.
The pyrolytic programme has
ended and the oven is cold,
but the door is locked and
symbol is flashing.
You did not turn the control
dial to position when the
pyrolytic programme ended.
1. Turn the control dial to
position and wait for 1
minute.
2. Turn the control dial to
position and wait for 1
minute.
3. Turn the control dial to
position again and wait
until pilot light turns off.

10
INCIDENT CAUSE SOLUTION
The control dial is in position
and the door is still loc-
ked.
The oven has not cooled down
to the safe temperature.
Wait until the temperature
lowers and pilot light turns
off.
The control dial is in position
, the oven is cold and the
door is still locked.
You have not followed the
instructions to cancel the
operation correctly.
1. Turn the control dial to
position and wait for 1
minute.
2. Turn the control dial to
position and wait for 1
minute.
3. Turn the control dial to
position again and wait
until pilot light turns off.
I have turned the control dial
to position . The pilot light
is lit up, the P symbol is
flashing on the timer display
and there is a beep every 5
seconds.
You have not selected one of
the programmes (P1, P2 or
P3).
Press + or – to choose one of
the programmes (P1, P2 or P3)
to start the pyrolytic cycle.

(AUS)
Think Appliances Pty Ltd.
416-424 Barry Rd
Coolaroo VIC 3048
Sales Telephone
1300 132 824
Service Telephone
1800 444 357
Website
www.thinkappliances.com
(NZ)
Applico Ltd.
Private Bag 92900
Onehunga, Auckland,
New Zealand 1061
Website
www.baumatic.co.nz
(UK)
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
[phone]
Website
www.baumatic.co.uk
Our contribution to enviromental protection: we use recycled paper. Cod.: 83172622/3172622-001