BDI MÜV 1252 User manual

1
C1 Top Panel x 2
A1 Glass Panel x 2
C2 Middle Panel x 2
C3 Bottom Panel x 2
H2 Swivel Locking
Casters x 8
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your BDI
products. Register today, and you will be entered to win free a
BINK table from BDI: www.bdiusa.com/register
Placement and Maintenance
Your Müv Table is designed for indoor use on level floors.
Clean glass with glass cleaner and wood veneer with a moist cloth.
Müv is engineered for easy assembly. Carefully follow this procedure to
prevent any damage. Do not use power tools for assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, contact BDI Customer Service at: [email protected].
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservic[email protected]om
Designed by Matthew Weatherly
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Muv & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2018, BDI
Made in China. 5.17.2019 V5
MÜV™ 1252
Tables
Tool Required:
Phillips Screwdriver
H1 M4 x 12mm
Pan Head Screw x 32
T1 Hex Driver x 1
Component List

bdiusa.com
customerservic[email protected]om
MÜV 1252
Table
2
Step 2 - Place the top panel C1 (which has a finger groove around the bottom edge as shown). Remove the
protective film from glass panel A1. Slide one edge of glass panel A1 (with aluminum rail) into the matching
slot on bottom side of top panel C1. If the aluminum channel is tight, brace the front edge of the top panel.
Step 3 - Take the middle panel C2 and position it as shown until the connectors engage with each other.
Make sure the edges are flush.
C1 Top Panel
A1 Glass Panel
Finger Groove
Wall

bdiusa.com
customerservic[email protected]om
MÜV 1252
Table
3
Step 4 - Place hex driver T1 into the access holes at a 45 degree angle and tighten the connectors by turning
clockwise about 1/4 turn until tight. You may need to wiggle the hex driver until the end of the driver engag-
es with the connecting hardware. Tighten all 4 connectors.
Step 5 - Orient the bottom panel C3 as shown and slide it so that the aluminum channel goes into the slot on
bottom panel C3. Keep sliding until the mitered edges align and touch. Wiggle and lift bottom panel C3 to
align the joint and close the seam.
4 access holes
to tighten connectors
C2 Middle Panel
T1 Hex Driver
C3 Bottom Panel
Aluminum Channel

bdiusa.com
customerservic[email protected]om
MÜV 1252
Table
4
Step 7 - Attach each swivel locking caster H2 with pan-head screws H1 and a Phillips screwdriver.
Repeat for all 4 casters.
H1 x 16
H1 x 4
H2
Phillips Driver (not included)
Step 6 - Tighten the 4 miter joint connectors by inserting hex driver T1 into the slanted holes and turning
clockwise until tight.
T1 Hex Driver
(45˚ angle)

bdiusa.com
customerservic[email protected]om
MÜV 1252
Table
5
Step 8 - Repeat steps 2-7 and assemble the other half of the table.
Step 9- With help from another person, carefully position the tables onto their wheels.
Step 10 - Your Müv Coffee Table comes with lockable casters. Raise the tab to lock, lower the tab to unlock.
Caution!
• The middle panels have hidden magnets to help align the 2 halves of your Müv table.
• Keep sensitive electronic equipment and fingers out of the path of the magnets.
Hidden Magnets
Lockable Casters