BDI VALERA 9729 User manual

E - Cam Bolt x 4
D - Dowel Pin x 8
C - Cam Fastener x 4
I - Upper Bracket x 4
J - Lower Bracket x 4
K - Shelf Clip x 4
F - 1/4-20 x 38mm
Machine Screw x 6
H - M6 x 6mm
Machine Screw
Hex Drive x 8
G - M6 x 20mm
Machine Screw
Hex Drive x 8
M - Rubber Stem Bumper
x 6
L - 5/32 x 12mm
Machine Screw x 4
Phillips Drive
A - Phillips Screwdriver
(Not Provided)
B - 4mm Hex L-Wrench
VALERA
Designed by Louis A. Lara
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
BDI are trademarks of Becker Designed, Inc.
All Rights reserved. © 2010 BDI
Made in Taiwan. 9729 Revision: 05-03-10
Component List
9729
ASSEMBLY INSTRUCTIONS
1
BDIUSA.COM [e-mail]
Valera is engineered for easy assembly. Carefully follow this procedure to
prevent any damage.
Placement and Maintenance
Valera is designed for indoor use on level floors. Clean glass with glass cleaner,
and wood veneer with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. The assembly workspace should be
a non-marring surface such as carpet. For missing hardware pieces, please
contact BDI Customer Service at [e-mail]. For all other
concerns, please contact your BDI Retailer.
N - Top Panel x 1
O - Side Panels x 2
P - Base Assembly x 1
Q - Back Panel x 1
R - Glass Shelves x 2
N
O
O
P
Q
R

Cam Fastener (C)
Arrow to point up to start
VALERA
9729 ASSEMBLY INSTRUCTIONS
2 BDIUSA.COM [e-mail]
Step 2
Install Hardware onto Top Panel
Lay Top Panel (N) on its Top on a carpeted surface, with holes facing up.
Install Dowel Pins (D) and Cam Bolts (E) into Top Panel (N) using Phillips
Screwdriver (A).
Install Upper Brackets (I) onto Top Panel (N) with Machine Screws (G)
using 4mm Hex L-Wrench (B), do not fully tighten for ease of Back Panel
(Q) installation.
Step 3
Install Hardware into Side Panels
Install Cam Fasteners (C) into Side Panels (O)
as shown, align arrow on Cam Fastener (C) to
point up.
Step 4
Install Hardware into Bottom Panel
Install Lower Bracket (J) into Base Assembly
(P) with Machine Screws (G) and tighten using
4mm Hex L-Wrench (B).
Do not fully tighten Brackets for ease of Back
Panel (Q) installation.
D
E
E
D
A
B
I
J
C
O
O
C
G
G
B
UP

VALERA
9729 ASSEMBLY INSTRUCTIONS 3 BDIUSA.COM [e-mail]
Step 5
Attach Side Panels to Top Panel
Attach Side Panels (O) to Top Panel (N) by lowering Side
Panels (O) onto Dowel Pins (D) and Cam Bolts (E). Make
certain shelf pin holes face inward.
Tighten Cam Fasteners (C) with 4mm Hex L-Wrench (B).
Step 6
Attach Base Assembly
Insert Dowel Pins (D) into Side Panels (O).
Attach Base Assembly (P) to Side Panels (O) using Dowel
Pins (D) to align components. Make certain Upper
Brackets (I) and Lower Brackets (J) are on same side.
Tighten Machine Screws (F) with 4mm Hex L-Wrench (B).
After Base Assembly (P) is attached turn Unit over.
CAUTION: Do not turn unit over on Brackets.
B
O
N
E
D
N
O
O
N
O
P
F
F
F
F
B
O
O
N
D
D
D
Recommended
2-person Step
for easy
installation

VALERA
9729 ASSEMBLY INSTRUCTIONS
4 BDIUSA.COM [e-mail]
Step 7
Install Back Panel
Install Back Panel (Q) onto Upper Brackets (I) and Lower Brackets
(J) with Machine Screws (H) using 4mm Hex L-Wrench (B).
Fasten the Machine Screws (H) in the middle of the Back Panel (Q)
and then fasten the outside Machine Screws (H).
After Back Panel (Q) is installed, then tighten Upper Brackets (I) and
Lower Brackets (J).
Step 8
Install Glass Shelves
Note: Glass Shelves (R) are identical.
Install Rubber Stem Bumpers (M) into Base Assembly (P).
Install Lower Glass Shelf (R) onto Base Assembly (P). Slowly slide Glass Shelf (R)
into place under Lower Brackets (J).
Install Shelf Clips (K) into Side Panels (O) at desired height and tighten with
Phillips Screwdriver (A). Make certain set screw on Shelf Clips (K) faces down.
Install Middle Glass Shelf (R) into Shelf Clips (K) and tighten set screws on Shelf
Clips (K) with Phillips Screwdriver (A).
Fasten the screws in the middle
of the panel and then
fasten the outside screws.
Shelf Clip (K)
Set screw faces down.
Carefully slide Glass Shelf (R)
under Lower Brackets (J).
H
H
H
H
H
H
H
H
B
Q
A
LK
R
R
Recommended
2-person Step
for easy
installation
H
B