BDI Odeon 9940 User manual

1
R - Phillips Screwdriver x 1
S-Hex Driver x 1
H-Cabinet x 1
J-Button Screw x 4
O-Phillips Head Mounting
Screws - M4, M5, M6, and M8
I-Flanged Nut x 4.
P-Plastic Spacer (Large & Small) x 8
U-Universal Mounting Bracket x 2
F-Handle x 1
D-Back Panel x 2
T-Base Assembly x 2
Q-Machine Screw x 2
B-Upper Bracket x 1
C - Lower Bracket x 1
N-Insert Pin x 1
M-Medium Hex Screw x 1
L-Long Hex Screw x 6
K - Handle Screw x 2
E-Tube Bracket x 1
G-Wood Base x 2
A-Vertical Tube x 1
V-Washer x 4
M2 - Washer x 1
Your Odeon Home Theater Furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
Placement and Maintenance
Odeon Home Theater Furniture is designed for indoor use on level floors.
Clean glass with glass cleaner, and steel parts and wood veneer with a
moist cloth.
Step 1
Unpack and identify the parts listed. The assembly workspace should be a
non-marring surface such as carpet. For missing hardware pieces please
contact BDI Customer Service at [email protected]. For all
other concerns, please contact your BDI Retailer.
Component List
Designed by Matthew Weatherly.
‘Odeon’ is a trademark of Becker Designed, Inc.
All rights reserved. ©2009 Becker Designed, Inc.
Made in China. 9940REV101909v4
Od e O n
9940
a s s e m b l y instructions
b d i u s a .c o m customerservice@b d i u s a .c o m

2
assembly instructions
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
K x 2
F
Step 2
Install Handle (F) to flip-down door using Phillips Screwdriver (R) and
Handle Screw (K).

3
assembly instructions
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Step 3
Turn Cabinet (H) on its backside. With door fully opened, install Base
Assembly (T) and Wood Leg (G) using Long Hex Screw (L) and Hex
Driver (S).
L x 6
G
T x 2

4
assembly instructions
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Step 4
Install Vertical Tube (A) to Cabinet (H) by lowering tube through
grommets (pre-installed).
Step 5
Attach Vertical Tube (A) to bottom shelf of Cabinet using
Medium Hex Screw (M), Washer (M2) and Hex Drive
(S). Install Insert Pin (N) to rear side of Vertical Tube (A)
using Phillips Screwdriver (R).
A
N
M
M2

5
assembly instructions
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Step 6
Install Tube Bracket (E) to rear side of cabinet using Hex Driver (S)
and Machine Screw (Q).
Step 7
Install Back Panel (D) to rear side of cabinet.
E
Q x 2
D x 2

6
assembly instructions
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
B
C
B
J x 4
Step 8
Attach Upper Bracket (B) to upper portion of Vertical Tube (A) as
shown below. Using Hex Driver (S), install Button Screws (J).
Step 9
Attach Lower Bracket (C) to lower portion of Vertical Tube (A) using
Hex Driver (S) and Button Screw (J). Note: Be sure to measure
mouting hole location on rear side of TV prior to installing Lower
Bracket (C).

7
assembly instructions
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Flat Screen TV
(back view)
Short Mounting
Screw
Washer
Universal Mounting
Bar
I x 4
Step 10
Install Universal Mounting Brackets (U) to rear side of flat panel TV.
Install Flanged Nuts (I) and Washer (V) to Upper Mounting Bracket
(B) so that it’s partially threaded half way.
Once the threaded post are positioned through the
key holes and slots, lower TV into resting position.
Tighten Flanged Nuts (I) on Upper Mounting Bracket
(B)
Install the second set of Flanged Nuts (I) to the
threaded posts of the Lower Mounting Bracket (C).
Once positioned, fully tighten all Flanged Nuts (I)!