BDI ZONA User manual

1
Product Registration
Registering your new BDI product allows us to send you
important product updates, service information and helpful hints
related to your BDI products. Register today, and you will be
entered to win free a BINK table from BDI:
www.bdiusa.com/register
Placement and Maintenance
Your Zona Console is designed for indoor use on level floors.
Clean glass with glass cleaner, and steel parts and wood veneer
with a moist cloth. Zona is engineered for easy assembly.
Carefully follow this procedure to prevent any damage. Do not
use power tools for assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly
workspace should be a non-marring surface such as carpet.
For missing hardware pieces, contact BDI Customer Service at:
[email protected].
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservic[email protected]om
Designed by BDI Studio.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Zona & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2016, BDI
Made in China. 11.10.2016 V1
ZONA™8859-ZO-CO__
4 DOOR CONSOLE
T2 Hex Wrench x 1
A1 Cabinet x 1
H1 1/4-20 x 15 mm
Machine Screw x 8
H2 1/4-20 x 63 mm
Machine Screw x 8
H4 KLEET™ Cord Wrap x 2
C5 Back Panels x 2
C4 Adjustable Side
Shelf x 2
C3 Adjustable Middle
Shelf x 1
A2 Sub-frame C2 Leg x 2
T1 Phillips Screwdriver x 1

bdiusa.com
customerservic[email protected]om
ZONA 8859-ZO-CO__
CONSOLE
2
Step 2 - Attach the 2legs C2 to sub-frame A2 with 8screws H1 using hex wrench T2.
Make sure the red arrow on the sub-frame faces the same direction as the direction of the ends of the legs.
Step 3 With help from another person, carefully position cabinet A1 upside-down. Caution-do not remove
packaging holding the shelves inside the cabinet. Attach the base to the cabinet with 8 screws H2 using hex
wrench T2. Do NOT fully tighten until all 8 screws are started.
H1 Screw x 8
A2
C2
H2 x 8
2 Person Ta sk
T2
H1
T2

bdiusa.com
customerservic[email protected]om
ZONA 8859-ZO-CO__
CONSOLE
3
Step 4 - Adjust your Shelves
With help from another person, carefully rotate your Zona Console onto its feet. The shelf pins located inside all
three cabinet spaces may be repositioned using screwdriver T1, allowing you to raise or lower the adjustable
middle and adjustable side shelves C3 and C4 to the desired level.
2 Person Ta sk
C3
C4
C4
T1
Step 5 - The 2 back panels C5 are removable and can slide towards the middle. To remove lift up and pull the
bottom edge out of its groove. To re-install, put the top edge of the back panel into the top groove, then drop
the bottom edge into the bottom groove.
Your Zona Console comes with 2KLEET cord wraps H4. Remove the adhesive backing and adhere the cord
wraps onto the back as shown (or where desired).
2
1
C5
C5
H4 Cord Wrap
H4 H4

bdiusa.com
customerservic[email protected]om
ZONA 8859-ZO-CO__
CONSOLE
4
Fine tuning your new BDI Media Furniture
These steps are to be followed after you have unpacked and completed the simple assembly instructions for
your console. Due to jostling in freight or perhaps an uneven floor, the doors on your cabinet may not appear
to be in perfect alignment. Making a few minor adjustments can rectify this situation. The high-quality European
hinge hardware is adjustable. Through a little adjustment, you can modify the orientation of the cabinet doors to
make sure that they are sitting perfectly on your unit.
STEP 1 - Level your unit
Levelers are integrated into each leg assembly and are accessed at the bottom of each cabinet leg. If your floor
is uneven, you may extend one or more levelers to attain a level, stable cabinet placement. Turning the leveler
clockwise will extend the leveler; turning it counter-clockwise will retract it.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your console should be evenly spaced and the doors should open and close freely without rubbing
against the door frame. If the cabinet’s doors appear out of alignment, this condition can be corrected with
minor adjustment to the European hinges on each door. Because these hinges are adjustable, adjusting one
hinge element can sometimes cause the need for adjustments to other Zona. But with a few adjustments, you
can modify the orientation of the cabinet doors to make sure that they hang
perfectly within your cabinet.
Use the Phillips Screwdriver T1 supplied to adjust the door hinges:
• By adjusting Screw 1, the door will move LEFT or RIGHT within the frame.
Make minor adjustments at both top and bottom hinges for best results.
• By adjusting Screw 2, the door will move UP or DOWN.
• By adjusting Screw 3 the entire door will move IN or OUT, opening or
closing the gap between the door frame and cabinet. (This screw rarely
needs adjustment.)
Tightening screw 1
on top hinge will open the
seam between Door C
& Door D here.
Loosening screw 1
on this hinge will close
the seam between Door C
& Door D here.
Door A Door B Door C Door D
Door C
1 2 3