BDI TANAMI 7120 User manual

1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today, and you will be entered to win free a
BINK table from BDI: www.bdiusa.com/register
Placement and Maintenance
Your Tanami Bar is designed for indoor use on level floors.
Clean wood, metal, and porcelain surfaces with a damp cloth.
Tanami is engineered for easy assembly. Carefully follow this procedure
to prevent any damage. Do not use power tools for assembly of this
product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, contact BDI Customer Service at:
[email protected].
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservic[email protected]om
Designed by Matthew Weatherly.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Tanami & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2019, BDI
Made in China. 11.12.2019
TANAMI™7120
BAR
C1 Cabinet x 1
C4 Glass x 1
C6 Drawer Liner x 1
C5 Adjustable Shelf x 1
T1 Hex Wrench x 1
H2 M6 x 12mm Screw x 8
H3 M6 x 76mm Screw x 2
H4 Adhesive Bumper x 4
C2 Leg x 2
C3 Cross Bar x 1
T2 Leveler Wrench x 1
H1 M6 x 12mm
Flathead Screw x 4

bdiusa.com
customerservic[email protected]om
TANAMI 7120
BAR
2
Step 3 - Base Attachment
With help from another person, carefully position cabinet C1 on its back (on top of a few layers of packing
material). Attach the base to the bottom of cabinet C1 as shown using 8 screws H2 going through the
metal tabs and 2 screws H3 going through the cross bar. With all screws started, tighten all screws
with hex wrench T1. See Detail on next page.
Step 2 - Base Assembly
Find the 2 legs inside Cabinet C1. Position 2 legs C2 towards the ends of cross bar C3 as shown mak-
ing sure the countersunk holes on the legs are facing outward. Use 4 flathead screws H1 and hex
wrench T1 to assemble the base. Do not fully tighten the screws yet.
2 Person Ta sk
C2
C2
T1
C1
H1
H1 x 4
H1
H2
H2
C3
H2
H2
H2
H2
H2
H2
H3
H3
T1

bdiusa.com
customerservic[email protected]om
TANAMI 7120
BAR
3
H2
H2
H3
H2
H2
metal tabs
Step 3 - Base Attachment (continued)
Step 4 - Bumpers
Remove paper backing and attach adhesive bumpers H4 to the bottom corners of the glass C4
positioned approximately 1cm (3/8") away from the edges. NOTE: bottom of the glass is painted white.
H4
H4
H4
H4
H4 Adhesive bumper x 4
C4

bdiusa.com
customerservic[email protected]om
TANAMI 7120
BAR
4
2 Person Ta sk
Step 5 - Stand Upright / Install Glass
With help from another person lift and rotate the cabinet onto its base, being careful to prevent it from
sliding on the floor. With painted surface and bumpers facing down, place the glass C4 on top of
cabinet C1 and align the edges with the edges of the cabinet.
Step 6 - Adjustable shelf and Drawer Liner
Install the adjustable drawer C5 in the lower right quadrant. Open the drawer and install the drawer
liner C6.
C4
C1
C6 drawer liner x 1
C5 Adjustable shelf x 1

bdiusa.com
customerservic[email protected]om
TANAMI 7120
BAR
5
Step 7 - Levelers & Shelf adjustment
Once the unit is completely assembled and in its final position, adjust the levelers using Leveler Wrench
T2. To hold the doors in an open position, partially dial out the two front levelers. This action will tilt the
cabinet back slightly, preventing the open doors from swinging towards their closed position. Leveling the
cabinet will also help align the 2 front doors (see step 8).
The shelf height in the lower right quadrant may be adjusted up or down. If desired, unscrew the 4 shelf
pins and reposition at the desired level.
dial out

bdiusa.com
customerservic[email protected]om
TANAMI 7120
BAR
6
Step 8 - Adjusting the Door Gaps
With both doors closed, check to see if the top corners of the doors align. If not, dial out the correspond-
ing front leveler under the door that is sagging.
Example:
If the door on the right is low, dial out the right front leveler to raise the door back into alignment with the
left door.
To move the right door up, dial
the front, right leveler out.
To move the left door up, dial the
left, front leveler out.
Dial out