BDI Sequel User manual

1
Placement and Maintenance
Sequel™ Home Office Furniture is designed for indoor use on level floors. Clean glass
with glass cleaner, and steel parts and wood veneer with a moist cloth. Your Sequel™
Home Office Furniture is engineered for easy assembly. Carefully follow this procedure
to prevent any damage.
Do not use power tools for assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly workspace should be a
non-marring surface such as carpet. For missing hardware pieces, please contact BDI
Customer Service at [email protected]. For all other concerns, please
contact your BDI Retailer.
Designed by Matthew Weatherly.
‘Sequel’ is a trademark of Becker Designed, Inc.
All rights reserved. ©2015 Becker Designed, Inc.
Made in Taiwan. 6002REV082515v7
G- 1/4-20 x 63 mm Screw x 6
H- 1/4-20 x 16 mm Screw x 16
F- 4mm Hex Wrench x 1
Component List
B- Top Glass x 1
D- Front Kick Panel x 1
C- Back Panel x 1
(optional)
L- Right Leg x 1
K- Left Leg x 1
M- Glides x 4
A - Frame Assembly x 1
E- Lower Horizontal Beam x 1
N- Upper Horizontal Beam x 1
sequel®
6002
return
assembly instructions
bdiusa.com [email protected]

assembly instructions
bdi
usa.com [email protected]
2
sequel®
6002 RETURN
Step 1
Install Glides (M) to the bottom of Left Leg (K) and Right Leg (L).
M x 4
LK

assembly instructions
bdi
usa.com [email protected]
3
sequel®
6002 RETURN
L
A
H
H
Step 2
Attach Left Leg (K) to Frame Assembly (A) using Screw (H) and
Hex Wrench (F).
Step 3
Attach Right Leg (L) to Frame Assembly (A) using Screw
(H) and Hex Wrench (F).
K
A

assembly instructions
bdi
usa.com [email protected]
4
sequel®
6002 RETURN
Step 4
Attach Upper Horizontal Beam (N) to inside of Left and Right Leg using
Screw (H) and Hex Wrench (F).
N
H
H

assembly instructions
bdi
usa.com [email protected]
5
sequel®
6002 RETURN
Step 5
Attach Lower Horizontal Beam (E) to inside of Left and Right Leg using
Screw (H) and Hex Wrench (F).
2 Person Task
E
H
H

assembly instructions
bdi
usa.com [email protected]
6
sequel®
6002 RETURN
Step 6
With the help of another person, gently lower Assembly onto Top Glass
(B). Both parts will be placed upside down for the assembly process and
fasten into place using Screw (G) and Hex Wrench (F) at all (7) fastener
locations. DO NOT OVERTIGHTEN! With the help of another person, turn
return upright onto its base.
B
G
G
G
G
G
G
G
G
2 Person Task

assembly instructions
bdi
usa.com [email protected]
7
sequel®
6002 RETURN
Step 7
Place Sequel Return in desired location. Once all of the electrical wires are routed,
install Kick Panel (D) as shown above. The rear side of panel has magnets that
will hold the panel in place. Note: The Sequel Return is designed to permit
placement in front of an electrical outlet for easier wiring access.
Optional Step
If return is located in the middle of a room, the optional 6009 Back Panel (C) is
available for purchase to conceal wire management. Please contact BDI Customer
Service at [email protected] or 800-428-2881
D
C