BDI VENUE 8649G User manual

1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today, and you will be entered to win free a BINK
table from BDI: www.bdiusa.com/register
Placement and Maintenance
Your Venue console is designed for indoor use on level floors. Clean
glass with glass cleaner, and steel parts and wood veneer with a moist
cloth.
Venue is engineered for easy assembly. Carefully follow this procedure
to prevent any damage. Do not use power tools for assembly of this
product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, please contact BDI Customer Service at:
[email protected].
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservic[email protected]om
Designed by Louis A Lara.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Venue & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2016, BDI
Made in China. 08.02.2016 V1
VENUE™8649G/8649W
MEDIA CONSOLE
T2 Hex Wrench x 1
T1 Phillips Screwdriver x 1
A1 Cabinet x 1
8649G - 2 wood / 2
glass doors
8649W - 4 wood
doors
H1 1/4-20 x 16 mm
Machine Screw x 20
H2 Leveler x 4
H3 KLEET™ Cord Wrap x 2
C5 Back Panels x 2
C4 Side Shelf x 2
C3 Middle Shelf x 2
C1 Sub-frame x 2
C2 Leg Frame x 2

bdiusa.com
customerservic[email protected]om
VENUE 8649 G/W
MEDIA CONSOLE
2
Step 2 - Attach the 2 Sub-frames C1 to one of the Leg frames C2 with 6Screws H1 using Hex wrench T1.
Do NOT fully tighten yet.
Step 3 - Attach the second Leg Frame C2 to the Sub-frames with 6 screws H1. Do NOT fully tighten yet.
H1 Screw x 6
H1 Screw x 6
T2
T2
C1 x 2
C2
C2
C2
C1

bdiusa.com
customerservic[email protected]om
VENUE 8649 G/W
MEDIA CONSOLE
3
Step 4 - Install 4 Levelers H2 into the threaded holes on the bottom of the Leg Frames.
H2 Leveler
x 4
Step 5 - Remove shelves from Cabinet.
Remove any packing material that may be above the shelves. One at a time, remove the 4 internal shelves
from the cabinet by lifting the edge (opposite the hinge side) upward and carefully pulling out.
A1

bdiusa.com
customerservic[email protected]om
VENUE 8649 G/W
MEDIA CONSOLE
4
Step 7 - Wire Management
With help from another person, carefully rotate Venue onto its feet. The 2 Back Panels C5 are removable. To
remove lift up and pull the bottom edge out of its groove. To re-install, put the top edge of the back panel into
the top groove, then drop the bottom edge into the bottom groove.
Venue Media Console comes with 2KLEET Cord Wraps H3. Remove the adhesive backing and adhere the
Cord Wraps onto the back of the leg as shown (or on the bottom of the cabinet if preferred). Velcro straps are
included under the top panel for your convenience to facilitate wire management.
2 Person Task
2
1
C5
C5
H3 Cord Wrap
Velcro Straps
Step 6 - With help from another person, carefully lay the Cabinet A1 on its top (upside down). Attach the
base assembly to the bottom of the Cabinet A1 with 8 Screws H1 as shown using Hex Wrench T2. Once all
screws have been started, fully tighten all base screws.
2 Person Task
H1 1/4-20
Screw x 8
T2
A1

bdiusa.com
customerservic[email protected]om
VENUE 8649 G/W
MEDIA CONSOLE
5
Step 8 - Adjustable Shelves
Reinstall the shelves. The shelf pins located inside all 4 cabinet spaces may be repositioned using Screwdriver
T1, allowing you to raise or lower the shelves C3 and C4 to the desired level.
T1
C3
C3
C4

bdiusa.com
customerservic[email protected]om
VENUE 8649 G/W
MEDIA CONSOLE
6
Fine tuning your new BDI Venue Home Theater Furniture
These steps are to be followed after you have unpacked and completed the simple assembly instructions for
your AV cabinet. Due to jostling in freight or perhaps an uneven floor, the doors on your cabinet may not appear
to be in perfect alignment. Making a few minor adjustments can rectify this situation. The high-quality European
hinge hardware is adjustable. Through a little adjustment, you can modify the orientation of the cabinet doors to
make sure that they are sitting perfectly on your unit.
STEP 1 - Level your unit
Levelers are integrated into each leg assembly and are accessed at the bottom of each cabinet leg. If your floor
is uneven, you may extend one or more levelers to attain a level, stable cabinet placement. Turning the leveler
clockwise will extend the leveler; turning it counter-clockwise will retract it.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing
against the door frame. If the cabinet’s doors appear out of alignment, this condition can be corrected with minor
adjustment to the European hinges on each door. Because these hinges are adjustable, adjusting one hinge
element can sometimes cause the need for adjustments to other elements. But with a few adjustments, you can
modify the orientation of the cabinet doors to make sure that they hang perfectly within your cabinet.
Use the Phillips Screwdriver T1 supplied to adjust the door hinges:
•By adjusting Screw 1, the door will move LEFT or RIGHT within the frame.
Make minor adjustments at both top and bottom hinges for best results.
•By adjusting Screw 2 the entire door will move IN or OUT, opening or
closing the gap between the door frame and cabinet. (This screw rarely
needs adjustment.)
21
1
2
Example of a tight seam.
Top hinge on Door C
must be moved to the
left.
Example of an open seam.
Bottom hinge of Door C
must be moved to the right.
Tighten this screw to
move door away from
the adjacent door.
Loosen this screw to
move door towards
the adjacent door.
Door C