BDI Odeon 9940 User manual

8/2008
OdeonTM 9940
Assembly Instructions
HIGH PERFORMANCE
FURNITURE FOR YOUR
HOME THEATER

2
Odeon™Home Theater Furniture
Placement and Maintenance
Odeon™Home Theater Furniture is designed for indoor use on level floors. Clean
glass with glass cleaner, and steel parts and wood veneer with a moist cloth.
www.bdiusa.com
customerser[email protected]
Unpack and identify the parts listed on this page.
The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact
BDI Customer Service at: customerser[email protected] For all other concerns please contact your local BDI Retailer.
Designed by Matthew Weatherly.
‘Odeon’ is a trademark of Becker Designed, Inc.
All rights reserved. ©2008 Becker Designed, Inc.
Your Odeon™Home Theater Furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
R- Phillips Screwdriver x 1
Step 1
S- Hex Driver x 1
H- Cabinet x 1
J- Button Screw x 4
O- Phillips Head Mounting
Screws - M4, M5, M6, and M8
I- Flanged Nut x 4.
P- Plastic Spacer (Large & Small) x 8
U- Universal Mounting Bracket x 2
F- Handle x 1
D- Back Panel x 2
T- Base Assembly x 2
Q- Machine Screw x 2
B- Upper Bracket x 1 C- Lower Bracket x 1
N- Insert Pin x 1
MLong Hex Screw x 1
LMedium Hex Screw x 6
KHandle Screw x 2
E- Tube Bracket x 1
G- Wood Base x 2
A- Vertical Tube x 1
V- Flanged Nut x 4.
M2 Washer x 1

3
Step 2
Install Handle (F) to flip-down door using Phillips Screwdriver (R) and Handle Screw (K).
Kx 2
F

4
Step 3
Turn Cabinet (H) on its backside. With door fully opened, install Base
Assembly (T) and Wood Leg (G) using Medium Hex Screw (L) and Hex
Driver (S).
Lx 6
G
Tx 2

5
Step 4
Install Vertical Tube (A) to Cabinet (H) by lowering tube through
grommets (pre-installed).
Step 5
Attach Vertical Tube (A) to bottom shelf of Cabinet using Long
Hex Screw (M), Washer (M2) and Hex Drive. Install Insert Pin
(N) to rear side of Vertical Tube using Phillips Screwdriver.
A
N
M
M2

6
Step 6
Install Tube Bracket (E) to rear side of cabinet using
Hex Driver (S) and Machine Screw (Q).
Step 7
Install Back Panel (D) to rear side of cabinet.
E
Qx 2
Dx 2

7
Step 8
Attach Upper Bracket (B) to upper portion of Vertical Tube (A) as shown below.
Using Hex Driver (S), install Button Screws (J).
Step 9
Attach Lower Bracket (C) to lower portion of Vertical Tube (A) using
Hex Driver (S) and Button Screw (J). Note: Be sure to measure
mouting hole location on rear side of TV prior to installing Lower
Bracet (C).
B
C
B
Jx 4

8
Step 10
Install Universal Mounting Brackets (U) to rear side of flat panel TV. Install flanged nut (I)
to upper mounting bracket so that it’s partially threaded half way.
Flat Screen TV
(back view)
Short Mounting
Screw
Washer
Universal Mounting Bar
Once the threaded post are positioned through the key
holes and slots, lower TV into resting position. Tighten
Flanged Nuts (I) on Upper Mounting Bar.
Install the second set of Flanged Nuts (I) to the threaded posts of the Lower
Mounting Bracket. Once positioned, fully tighten all Flanged Nuts!
I x 4