BEA Eagle Operator's manual

75.5957.02 EAGLE FAMILY 20181130 Page 1 of 4
1
2
5
3
4
EAGLE & EAGLE HM
DESCRIPTION
Unidirectional activation sensor for automatic,
pedestrian doors and high-mount doors
ENGLISH
1. main connector
2. wide zone antenna (Eagle only)
3. narrow zone antenna (optional for Eagle, default for Eagle HM)
4. push buttons
5. cover
TECHNICAL SPECIFICATIONS
Technology: microwave and microprocessor
Transmitter frequency: 24.150 GHz
Transmitter radiated power: < 20 dBm EIRP
Transmitter power density: < 5 mW/cm²
Detection mode: motion
Min. detection speed: 2 in/s
Supply voltage: 12 – 24 VAC ±10%; 12 – 24 VDC +30% / -10%
Mains frequency: 50 – 60 Hz
Max power consumption: < 2 W
Output:
max. contact voltage:
max. contact current:
max. switching power:
relay (free of potential changeover contact)
42V AC/DC
1A (resistive)
30W (DC) / 60VA (AC)
Mounting height: Eagle: 6’ – 13’
Eagle HM: 10’ − 16’6"
Degree of protection: IP54
Temperature range: -4 – 131 °F
Dimensions: 4.7" (L) × 3.1" (H) × 2.0" (W)
Tilt angles: 0 – 90° vertical; -30 – 30° lateral
Material: ABS
Weight: 7.6 oz
Cable length: Eagle: 8’
Eagle HM: 30’
Norm conformity: R&TTE 1999/5/EC, LVD 2006/95/EC, RoHS 2 2011/65/EU
Specifications are subject to change without prior notice.
All values measured in specific conditions.
The image shown here is a standard Eagle.
Antennae differ between the standard and high-mount versions of the Eagle.
Visit website for
available languages of
this document.

Page 2 of 4 75.5957.02 EAGLE FAMILY 20181130
1
4
2 3
7 ft
7 ft
INSTALLATION TIPS
MOUNTING & WIRING
MECHANICAL ADJUSTMENTS
BEFORE MOUNTING AFTER MOUNTING
If using EAGLE SPACER or EAGLE SPACER V, please refer to User’s Guide 75.5981 before beginning.
• Do not touch electrical parts.
• Avoid vibrations.
• Do not cover the sensor.
• Avoid proximity to neon lamps or moving objects.
• The sensor may be mounted horizontally or vertically (e.g. on a ceiling or on a wall, respectively).
◊ If mounting horizontally, the sensor must be mounted in front of the door.
◊ If mounting vertically, the sensor must be mounted above the door.
Apply the mounting template.
Drill 1 hole for the cable and
pull it through.
Drill 2 holes for the screws.
Standard EAGLE only: Choose the appropriate antenna
(narrow or wide) for the correct detection zone width.
Narrow: 6’ 6" ×8’
Wide: 13’ ×6’ 6"
EAGLE HM only offers narrow antenna.
See diagram below for how to change antennas.
Position the cable as indicated.
Mount the sensor firmly.
Connect the wires accordingly:
1: RED - POWER SUPPLY +
2: BLACK - POWER SUPPLY -
3: WHITE - COM
4: GREEN - NO OR 5: GREEN - NC
WIDE
NARROW
How to Open the Sensor:

75.5957.02 EAGLE FAMILY 20181130 Page 3 of 4
XXS
0.5 s
XS
1 s
auto
< 10 ft
low
bi
A
S
2 s
open
> 10 ft
normal
uni
P
>
3 s
closed
high
uni
MTF
>
4 s
>
uni
AWAY
>
5 s
>
MTF &
AWAY
>
6 s
>
L
7 s
L
XL
8 s
XL
XXL
9 s
highest
+
7 ft 7 ft
5
6
10 ft 10 ft
MECHANICAL ADJUSTMENTS (cont.)
SETTINGS (by remote control or push-buttons)
If desired, adjust the antenna angle (laterally and/or vertically) to position the detection field.
When mounting at the maximum height, BEA recommends a 15° tilt angle.
Observe antenna type (narrow or wide) in the illustrations below.
Program the sensor for the desired application.
When mounting at the maximum height, BEA recommends the following:
Immunity = low
Zone Size = XXL
LATERAL ADJUSTMENT VERTICAL ADJUSTMENT
ZONE SIZE
IMMUNITY FILTER
DETECTION MODE
OUTPUT
CONFIGURATION
HOLD-OPEN TIME
MOUNTING
HEIGHT
DOOR CONTROL
bi = two-way detection
uni = one-way detection towards sensor
uni MTF = one-way detection with motion tracking feature
uni AWAY = one-way detection away from sensor
A = active output (NO-contact); relay energizes upon detection
P = passive output (NC-contact); relay de-energizes upon detection
Standard Eagle default = < 10 ft
High-mount Eagle default = > 10 ft
open = the sensor detects constantly. The LED is ON.
closed = the sensor is in standby and does not detect. The LED is OFF.
FACTORY VALUES
USING REMOTE CONTROL: USING PUSH-BUTTONS: > 2 sec
WIDE WIDE
NARROW NARROW
RESETTING TO FACTORY VALUES
ACCCESS CODE
The access code (1 to 4 digits) is recommended to set sensors installed close to each other.
SAVING AN ACCESS CODE:
DELETING AN ACCESS CODE:
Once you have saved an access code, you always need to enter this code to unlock the sensor.
If you forget the access code, cycle the power. For the first minute, you can access the sensor without an access code.

Page 4 of 4 75.5957.02 EAGLE FAMILY 20181130
TROUBLESHOOTING
The door remains
closed.
LED is off.
Sensor power is off. Check wiring and power supply.
Door control setting (F2) is set to
3 (closed).
Change door control setting (F2) to 1
(automatic).
Door does not react
as expected
Improper output configuration
on sensor.
Change the output configuration setting
on each sensor connected to the door
operator.
Door opens and
closes constantly
Sensor is disturbed by door
motion or vibrations from door
motion.
Ensure sensor is fixed properly.
Ensure detection mode is unidirectional.
Increase antenna angle.
Increase immunity filter.
Reduce zone size.
Door opens for no
discernable reason
It rains and the sensor detects
the motion of the rain drops.
Ensure detection mode is unidirectional.
Increase immunity filter.
Install rain accessory.
In highly reflective environments,
the sensor detects objects
outside of its detection zone.
Change the antenna angle.
Reduce zone size.
Increase immunity filter.
In airlock vestibules, the sensor
detects the movement of the
opposite door.
Change the antenna angle.
Change antenna.
Increase immunity filter.
LED flashes quickly
after unlocking
Sensor needs access code to
unlock.
Enter correct access code.
If you forgot the code, cycle the power to
access the sensor without access code.
Change or delete the access code.
Sensor does not
respond to the
remote control
Batteries in the remote control
are weak or installed improperly.
Check batteries and change if necessary.
Remote control not pointed
correctly.
Point remote control at sensor.
BEA, the sensor manufacturer, cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor/device; therefore, BEA
does not guarantee any use of the sensor outside of its intended purpose.
BEA strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for doors/gates, and factory-
trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor
system installation is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer recommendations
and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service
call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107).
Verify that all appropriate industry signage and warning labels are in place.
BEA INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462
General Tech Questions: T[email protected] | Tech Docs: www.BEAinc.com
©BEA | Original Instructions | PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING