BEA G3 User manual
4IR Presence Sensing Field: Width and Depth (wide lens installed as default)
Dimensions Are Approximate Size
IR Patterns
Mounting Height of Sensor
7’ 10’ 12’ 14’
Narrow Lens Depth of Two Curtains 1’3” 1’6” 1’8” 1’10”
Narrow Lens Width of Curtains 3’6” 5’ 6’ 7’
Wide Lens Depth of Two Curtains 1’3” 1’6” 1’8” 1’10”
Wide Lens Width of Curtains 6’6” 10’ 12’ 14’
1. The IR pattern may be adjusted by moving the pattern nearer or further away from the face of the door by adjusting the tilt angle from +4° to
-4°. A counterclockwise rotation of the adjustment screw will move the curtain further away from the door and clockwise rotation will move the
curtain toward the door. Precise location of the IR beam may be found by using BEA’s Spotnder P/N 10SPOT.
G3
QUICK SETUP GUIDE
COMBINED RADAR ACTIVATION AND ACTIVE INFRARED SAFETY SENSOR
The G3 Quick Setup Guide is for the installation and setup of the G3. This document is provided for installers and service personnel who are
familiar with the G3. For those who are not completely familiar with the installation and setup of the G3, BEA recommends following the detailed
installation and setup instructions found in the G3 User’s Guide document number 75.5640.
75.5641.01 20091112 Page 1 of 2
1Mount Sensor
1. Using scale on template, position drawing of sensor on template
0” to 2” from bottom of header.
NOTE: Flush mount with bottom of header is necessary for all
negative IR angles.
2. Drill hole marked for wire passage and drill pilot holes for screw
mounting. Remove template prior to sensor installation.
3. Insert mounting screws approximately halfway in and install the G3
on the screws. When in place, tighten screws to secure to header.
NOTE: Leave cover off until mechanical adjustments are complete.
2Cable Routing
1. With G3 in place, locate the enclosed cable and feed the stripped
end through the wire passage hole in the header.
2. Leave enough slack to allow connection to the G3 and proper
routing of wire around the plastic post.
NOTE: Observe proper routing of the cable as shown. This is
to divert rainwater from the G3 if water should run down
the cable. Proper routing of the wire also provides easier
installation of the cover.
Plastic Post
Cable / Wire
3Sensor Wiring
1. When connecting to a microprocessed control box, the motion output and presence output wires may be connected to separate inputs or may
also be connected to a mutual input. Some controls may only have an activation input, while others may have an activation input, as well as a
safety (or presence) input.
6 Wire Conguration (Preferred Conguration) 4 Wire Conguration (Mandatory Remote Setup: Unlock, F1, 1, Lock, Lock)
W
I
Z
A
R
D
•
PWR: Red - 12 to 24 VAC / VDC: -5% to +10%
• PWR: Black - 12 to 24 VAC / VDC: -5% to +10%
• COM: White - Common at Door Control
• ACTIV: Green - Activation at Door Control
• COM: Brown - Common at Door Control
• SAFETY: Blue - Safety at Door Control
C
O
N
T
R
O
L
W
I
Z
A
R
D
•
PWR: Red - 12 to 24 VAC / VDC: -5% to +10%
• PWR: Black - 12 to 24 VAC / VDC: -5% to +10%
• COM: White - Common at Door Control
• ACTIV: Green - Activation at Door Control
C
O
N
T
R
O
L
-4°
0°
max. 3” max. 3”
+4° -4°
0°
Sensor Plastic Pin Indicator Sensor Adjustment Screw
1 Description
2 Installation / Wiring / Setup
1/4
1/2
3/4
1
1-1/4
1-1/2
1-3/4
2
1/4
1/2
3/4
1
1-1/4
1-1/2
1-3/4
2
G3 MOUNTING TEMPLATE
Drill1/8” hole Drill1/8” hole
Drill 1/2”wire passage hole anywhere within this area
Do not mount lower than this line
Do not mount lower than this line
OBSOLETE
5Radar Motion Sensing Field: Width
6Radar Motion Sensing Field: Depth
3.2’ 6.4’3.2’6.4’
3.2’
6.4’
9.6’
3.2’ 6.4’3.2’6.4’
0
3.2’
6.4’
9.6’
13.1’
Sensitivity
0 (min) → 9 (max) default = 7
0
3
6
9
03.2’ 6.4’3.2’6.4’
0
3.2’
6.4’
9.6’
15°30°45°
30°
45°
15°
0°
Wide Pattern Narrow Pattern
7IR Presence Sensing Field / IR Assisted Setup
An Assisted Setup is Required after installation and any time after mechanical IR adjustments. With remote unlock, setup (magic wand), 0.
Or to perform a manual assisted set up; simply momentarily depress the right most push button on the top right of the G3. The red & green led
will alternately ash approximately 16 seconds during set up. Keep area clear of trafc during this process. If the G3 ashes fast red after the
assisted setup then an error has occurred. Repeat the assisted setup or see the G3 user guide troubleshooting section pages 8-9.
03.2’ 6.4’3.2’6.4’
0
3.2’
6.4’
9.6’
03.2’ 6.4’3.2’6.4’
0
3.2’
6.4’
9.6’
Wide Pattern Narrow Pattern
2nd Radar Antenna
Radar Motion Sensor
F1 Optional Setup Congurations F1
F1 Function: For a 4 wire connection in lieu of a 6 wire connection - see step 3 for wire connections.
The purpose of selecting safety output redirection using the universal remote (Unlock, F1, 1, Lock, Lock) is to allow the installer two options as
outlined below. With either option; it is absolutely mandatory to redirect the safety signal to the green & white wires. Using the remote control
follow this sequence: Unlock, F1, 1, Lock, Lock. If this is not done the safety signal will not keep the door(s) open if a person occupies
the threshold area even if the G3 red LED is indicating detection.
Option 1: To enable the G3 to function correctly with older non micrprocessed controls. This disables the brown and blue wire function and
redirects the output of the safety signal to the green and white wires. Both motion and presence will now output on the green (NO) and white
(COM) wires.
Option 2: If the installer wants a 4 wire connection in lieu of the preferred 6 wire connection, simply use the red and black wires for power and
the green (NO) and white (COM) for a combined output signal of the motion and presence zone.
◊Automatic Door Control Connections
BEA, Inc. Recommends a
dedicated transformer to power
the G3. Contact Technical
Support if you intend to utilize
the door control power supply.
ACT COM SAF ACT COM SAF
Besam 4000 5 & 7 617 & 19 Horton 2160 Blk Wht Grn
Besam amd1 2 & 4 6, 11 8 & 9 Hunter SS Com SB
Besam amd2 12 & 13 5, 11 7 & 9 KM Red Grn Yel
Besam uni 2 & 5 1, 4, 10 11 & 12 KM/Rec 5000 236
Dorma 6 1 2 Record 1 2 N/A
Dorma ESAII 15 & 18 16 & 19 (26 & 28)
(21 & 23)
Stanley Dura (TB2) 4 & 8 (TB2) 3 & 7 (TB3) 7 & 8
DOM Brn Brn Brn / Wht Stanley 521 (TB4) 4 & 8 (TB4) 3 & 7 (TB3) 7 & 8
GT1100 Blk Red Wht Tormax tlp/lc 2 & 4 3
Horton 2150 2 & 3 4, 7, 9 6Tormax tep/xp 2 & 7 3
Do not leave problems unresolved. If a satisfactory solution cannot be achieved after troubleshooting a problem, please call BEA, Inc. If you must wait for the
following workday to call BEA., leave the door inoperable until satisfactory repairs can be made. Never sacrice the safe operation of the automatic door or
gate for an incomplete solution. The following numbers can be called 24 hours a day, 7 days a week. For more information, visit www.beasensors.com.
Page 2 of 2 75.5641.01 20091112
NEW SIMPLIFIED G3 Setup Congurations IR Immunity
1: Normal
2: High (May be used in highly reective applications or in extreme cases of snow, rain, pedimats or lighting.)
0
0
0
Canada & Texas: 1-866-836-1863 Central: 1-800-407-4545
West: 1-888-419-2564 East: 1-866-249-7937
OBSOLETE
Other BEA Security Sensor manuals
