Becker Centronic EasyControl EC5410A-II User manual

Centronic EasyControl
EC5410A-II
en Assembly and Operating Instructions
10-channel hand-held transmitter
Important information for:
• Fitters / • Electricians / • Users
Please forward accordingly!
These instructions must be kept safe for future reference.
Becker-Antriebe GmbH
Friedrich-Ebert-Straße 2-4
35764 Sinn/Germany
www.becker-antriebe.com
4034 630 197 014/07/2022

Table of contents
General information ................................................................................. 3
Warranty ................................................................................................. 3
Safety instructions ................................................................................... 4
Intended use ........................................................................................... 5
Explanation of displays and buttons........................................................... 6
Explanation of functions ........................................................................... 7
Programming the transmitter .................................................................... 8
Installing the wall bracket.......................................................................... 9
Changing batteries................................................................................... 9
Cleaning.................................................................................................. 9
Technical data ........................................................................................10
What to do if...?.......................................................................................10
2-en

General information
Products such as roller shutter and sun protection systems, light controls and
remote-controlled sockets can be operated using the 10 transmission chan-
nels.
In addition to the 10 individual transmission channels, this transmitter also has
3 central transmission channels which operate transmission channels 1-5,
6-10 and 1-10.
This device is exceptionally easy to use.
Please observe these Assembly and Operating Instructions when installing
and setting up the equipment.
Explanation of pictograms
CAUTION CAUTION indicates a hazardous situation
which, if not avoided, could result in in-
jury.
ATTENTION ATTENTION indicates measures that must
be taken to avoid damage to property.
Denotes user tips and other useful in-
formation.
Warranty
Structural modifications and incorrect installation which are not in accordance
with these and our other instructions can result in serious injuries, e.g., crush-
ing of limbs. Therefore, structural modifications may only be carried out with
our prior approval and strictly in accordance with our instructions, particularly
the information contained in these Assembly and Operating Instructions.
Any further processing of the products which does not comply with their inten-
ded use is not permitted.
The end product manufacturer and fitter have to ensure that all the relevant
current statutory, official and, in particular, EMC regulations are adhered to
during utilisation of our products, especially with regard to end product manu-
facture, installation and customer advice.
3-en

Safety instructions
General information
•Please keep the instruction manual safe!
•Only use in dry rooms.
•Only use unmodified original parts from the control unit manufacturer.
•Keep children away from control units.
•Observe all pertinent country-specific regulations.
•Dispose of used batteries properly. Only replace the battery with one of
the same type (see Technical Data).
Caution
•Keep people out of the system’s range of travel.
•If the system is controlled by one or more transmitters,
the system’s range of travel must always be visible during
operation.
•Device contains small parts that can be swallowed.
Caution
THIS PRODUCT CONTAINS A LITHIUM BATTERY.
If swallowed, a lithium battery can cause severe or fatal in-
juries within 2 hours.
Keep batteries away from children.
If you think batteries may have been swallowed or placed in-
side any part of body, seek immediate medical attention.
4-en

Intended use
The transmitter described in these instructions must only be used for operat-
ing Centronic-compatible radio drives and radio control units.
•Please note that radio-controlled systems may not be used in areas with
a high risk of interference (e.g. hospitals, airports).
•The remote control is intended solely for use with equipment and sys-
tems in which malfunctions in the transmitter or receiver would not pose
any risk to persons, animals or property, or which contain safety devices
to eliminate such risks.
•The operator is not protected from interference from other telecommu-
nications systems and terminal equipment (e.g. even from radio-con-
trolled systems which are properly operated in the same frequency
range).
•Only connect radio receivers to devices and systems approved by the
manufacturer.
•Ensure that the control unit is not installed or operated
close to metal surfaces or magnetic fields.
•Radio-controlled systems transmitting on the same fre-
quency may cause reception interference.
•Note that the range of the radio signal is limited by legis-
lation as well as by design.
5-en

Explanation of displays and buttons
1
8
7
2
6
3
4
5
1. UP button
2. STOP button
3. DOWN button
4. Channel selection button
5. Channel indicator lamps
6. Programming button
7. Labelling field
8. Type plate
6-en

Explanation of functions
Channel
The channel of a transmitter can be programmed into one or more receivers.
One receiver is operated through an individual command, several receivers
through a group command.
Central command
If all the channels of the transmitter are selected, it is possible to operate all of
the assigned receivers/groups simultaneously.
Channel selection button
Up to 10 channels can be selected using the channel selection button. The in-
dividual channels are indicated by the corresponding LED lighting up.
Channel LED colour
1-5 and central command 1-5 green
6-10 and central command 6-10 red
1-10 central command orange
You can make a note of the programmed channel in the la-
belling field underneath the transparent film. If you keep the
channel selection button pressed for 3seconds, the channel
selection sequence will change.
Channel indicator lamps
A radio signal is indicated by the corresponding channel indicator lamp light-
ing up. The respective channel indicator lamp flashes while transmitting if the
battery is getting weak. The transmission strength and the radio range de-
crease as battery power declines. If the channel indicator lamp no longer
lights up when a button is pressed, the battery must be replaced.
7-en

Programming the transmitter
1) Programming the master transmitter
The central commands 1-5, 6-10 and 1-10 cannot be pro-
grammed separately.
a) Readying the receiver for programming
Follow the Assembly and Operating Instructions for the re-
ceiver.
Operate the programming button on the transmitter using a
suitable cylindrical tool (e.g. a ballpoint pen).
•Switch off the power supply to the receiver for 5 seconds, then switch it
back on
or
•Operate the programming button or the radio switch of the receiver.
The receiver is now in programming mode for 3 minutes.
b) Programming the master transmitter
Press the programming button on the master transmitter while in program-
ming mode until the receiver confirms that programming has been successful.
The programming process is now complete.
2) Programming additional transmitters
1. Press the programming button of the master transmitter until the re-
ceiver confirms.
2. Then press the programming button of the new transmitter until the re-
ceiver confirms.
3. Now press the programming button of the new transmitter again.
4. The receiver confirms successful programming.
8-en

Installing the wall bracket
Unlocking mechanism
Wall bracket
mounting
plate
Wall bracket
26
•Before installation in the de-
sired installation position,
check that the transmitter and
receiver are functioning prop-
erly.
•Fix the bracket to the wall with
the two screws enclosed.
Changing batteries
You will find the appropriate battery type in the "Technical
data" chapter.
Cleaning
Only clean the device with a suitable cloth. Do not use aggressive cleaning
agents that may damage the surface.
9-en

Technical data
Rated voltage 3 V DC
Battery type CR 2430
Degree of protection IP20
Permissible ambient temperature -10 °C to +55 °C
Maximum emitted transmission output ≤ 3 mW
Radio frequency 915.3 MHz
The maximum transmitter range on and in the building is up to 15m, and up to
150m in the open.
What to do if...?
Problem Remedy
Drive is not functioning. Insert a new battery.
Insert the battery correctly.
Reduce distance from receiver.
Program transmitter.
Desired drive is not functioning. Select correct channel.
10-en