Behringer 150 RING MOD/NOISE/S&H/LFO User manual

Quick Start Guide
150 RING MOD/NOISE/S&H/LFO
Legendary Analog Ring Modulator/
Noise/S&H/LFO Module for Eurorack
Controls
(1) EXT SIG X/NOISE jack routes audio signals or noise into the
ring modulator. The audio signal or noise coming in through
the EXT SIG X/NOISE jack is combined with and modulated
by the carrier signal routed into the EXT SIG Y/LFO jack.
(2) EXT SIG Y/LFO jack routes the carrier signal into the
ring modulator. The carrier signal can be in the audio
range, such as a 500 Hz sine wave, or a signal from
Low Frequency Oscillator (LFO).
(3) R.M OUT jack sends out the nal ring modulator signal.
(4) PINK output jacks oer dual white pink noise outputs for
use other modules.
(5) WHITE output jacks oer dual white noise outputs for use
with other modules.
(6) EXT SIG input jack routes external signals into the S&H
circuit for processing. Use the EXT/LFO/NOISE switch to
optimize the EXT SIG input for dierent types of signals.
(7) EXT/LFO/NOISE sliding switch optimizes the EXT SIG for use
with control signals (EXT), signals from a Low Frequency
Oscillator (LFO) or noise signals (NOISE).
(8) CLOCK OUT jack sends out a clock signal generated inside
the S&H circuit.
(9) CLOCK RATE slider controls the internal clock signal’s rate
before the clock signal is routed out through the CLOCK
OUT jack.
(10) S&H OUT jack sends out the nal S&H (Sample & Hold)
signal over cables with 3.5 mm TS connectors.
(11) LAG TIME slider can be used to smooth out the changes
between control voltage values as the slider is raised,
similar to a portamento or glide eect on a keyboard.
(12) EXT CLOCK IN input jack routes an external clock signal into
the S&H circuit.
(13) WAVEFORM knob selects between sine, triangle, square,
ramp and sawtooth waveforms for the LFO.
(14) FREQ RANGE sliding switch selects between high (H),
mid (M) and low (L) frequency ranges.
(15) TRIGGER jack allows a control voltage to trigger the LFO
waveform by resetting the amplitude to 0. The waveform
then returns to the original amplitude at a rate set by the
DELAY slider.
(16) FREQ slider ne-adjusts the LFO frequency within the range
chosen by the FREQ RANGE switch.
(17) DELAY slider controls the amount of time that elapses
between the beginning of a new note and the LFO’s
amplitude peak.
(18) FREQ CV IN input jack allows a control voltage to control
the LFO frequency in place of the FREQ slider.
(19) OUTPUT LEVEL sliding switch selects between a
full-strength LFO output signal (x1 setting) and a
1/10th-strength signal (x 1/10 setting).
(20) LFO OUT output jacks oer dual LFO outputs for use with
cables with 3.5 mm TS connectors.
Power Connection
The 150 RING MOD/NOISE/S&H/LFO module comes with the
required power cable for connecting to a standard Eurorack power
supply system. Follow these steps to connect power to the module.
It is easier to make these connections before the module has been
mounted into a rack case.
1. Turn the power supply or rack case power o and disconnect
the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
(1)
(3)
(4)
(10)(8)(6) (7)
(2) (9)
(14)
(16) (17) (19)
(20)
(13)
(12)
(18)
(15)
(11)
(5)

3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting in
a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that allows
individual threaded plates to slide along the length of the case.
The free-moving threaded plates allow precise positioning of the
module, but each plate should be positioned in the approximate
relation to the mounting holes in your module before attaching
the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded plate.
Attach the screws part way to start, which will allow small
adjustments to the positioning while you get them all aligned.
After the nal position has been established, tighten the
screws down.
Specications
Signal Connections
Ring modulator
Ext signal X / Y 2 x 3.5 mm jack
X Impedance 100 k unbalanced
Y impedance 100 k unbalanced
Maximum level +20 dBu
R.M out 1 x 3.5 mm jack
Impedance 100  unbalanced
Maximum level +15 dBu
Noise generator
White 2 x 3.5 mm jack
Impedance 1 k unbalanced
Output level 0 dBu
Pink 2 x 3.5 mm jack
Impedance 1 k unbalanced
Output level 0 dBu
S & H
Ext signal 1 x 3.5 mm jack
Impedance 100 k unbalanced
Maximum level + 17 dBu
Ext clock in 1 x 3.5 mm jack
Impedance 100 k unbalanced
Threshold > 1 V
Clock out 1 x 3.5 mm jack
Impedance 1 k unbalanced
S & H out 1 x 3.5 mm jack
Impedance 1 k unbalanced
LFO
Freq CV in 1 x 3.5 mm jack
Impedance 100 k unbalanced
CV input range 0 V to +10 V
LFO out 2 x 3.5 mm jack
Impedance 1 k unbalanced
Output level 1 V p-p / 10 V p-p
Controls
S & H
Clock rate 1 x slider, 2 Hz - 25 Hz
Lag time 1 x slider, 0 - 8 seconds
Ext / LFO / noise 3-way sliding switch
LFO
Freq range 3-way sliding switch
High / mid / low, selectable
Frequency 1 x slider, 0.03 Hz - 30 Hz in 3 ranges
Delay 1 x slider, 4 ms to 8 seconds
Waveform 5-way switch Sine / triangle / square /
sawtooth /inverted sawtooth, selectable
Output level 2-way sliding switch x⁄ / x1, selectable
Power
Power supply Eurorack
Current draw 60 mA (+12 V), 50 mA (-12 V)
Physical
Dimensions (H x W x D) 44 x 81 x 129 mm (1.7 x 3.2 x 5.1")
Rack units 16 HP
Weight 0.16 kg (0.35 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are
the property of their respective owners. Midas, KlarkTeknik, Lab Gruppen,
Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera,
Auratone and Coolaudio are trademarks or registered trademarks of MusicTribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding MusicTribe’s Limited Warranty, please see complete details online at
musictribe.com/warranty.
Zhongshan Eurotec Electronics Limited
No. 10Wanmei Road, South China Modern Chinese Medicine Park,
Nanlang Town, 528451, Zhongshan City, Guangdong Province, China