Behringer 173 QUAD GATE/MULTIPLES User manual

Quick Start Guide
173 QUAD GATE/MULTIPLES
Legendary Analog Quad Gate &
Multiples Module for Eurorack
Controls
(1) GATE OUT – Send the gate signal to another module via
3.5 mm TS cable.
(2) GATE IN – Connect an incoming signal via
3.5 mm TS cable.
(3) GATE CV – Connect a control voltage signal from other
modules to control gate operation, non-inverting
(active high) and inverting (active low) inputs.
(4) MULTIPLES – Connect a signal to the A jack that will be
sent to multiple designations via the B, C and D jacks in
the same row.
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow
small adjustments to the positioning while you get them all
aligned. After the nal position has been established, tighten the
screws down.
(1)
(2)
(3)
(4)

Specications LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, KlarkTeknik, Lab Gruppen, Lake,
Tannoy,Turbosound,TC Electronic,TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of MusicTribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding MusicTribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Zhongshan Eurotec Electronics Limited
No. 10 Wanmei Road, South China Modern Chinese Medicine Park,
Nanlang Town, 528451, Zhongshan City, Guangdong Province, China
Signal Input
Type 3.5 mm jack, DC coupled
Impedance 160 kΩ, unbalanced
Maximum input level +17 dBu
Signal Output
Type 3.5 mm jack, DC coupled
Impedance 1 kΩ, unbalanced
Maximum output level +17 dBu
Frequency response DC to 20 kHz
Output noise <-90 dBu, 22 Hz - 22 kHz
Gate Control
Type 2 x 3.5 mm jacks,
non-inverting and inverting
Impedance >50 kΩ, unbalanced
Switching threshold Non inverting > +3 V,
inverting < +1.5 V
Maximum input level 10 V p-p
Multiples
Type 24 x 3.5 mm TS mono jacks,
unbalanced
Arrangement 6 sets of 4 parallel jacks,
passive
Compatibility CV and audio signals
Power
Power supply Eurorack
Current draw 40 mA (+12 V),
40 mA (-12 V)
Physical
Dimensions 28 x 81 x 129 mm
(1.1 x 3.2 x 5.1")
Rack units 16 HP
Weight 0.18 kg (0.4 lbs)