Belanger DURAJET ARCH User manual

DURAJET™
Belanger, Inc®.
P.O. Box 5470
Northville, MI 48167-5470
ustomer Service Phone [phone]
Fax [phone]
www.Belangerinc.com
1MANUL028
REV 00
ARCH

Belanger® Equipment Owner’s Manual
DURAJET™ Arch
Copyright 2013
Belanger, Inc®
This manual and the accompanying equipment are protected by United States trademark, copyright, and patent laws. You
may make one copy of this manual. Do not make additional copies of this manual or electronically transmit it in any form
whatsoever, in whole or in part, without the prior written permission of Belanger, Inc.®
The registered trademarks used in this document are the property of their respective owners. The use of such trademarks is
for reference purposes only and does not imply sponsorship or approval of Belanger, Inc.®by these companies or any
companies affiliated with their respective owners.

DURAJET™ ARCH
1MANUL028 Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Table of Contents
Belanger Incorporated® Limited Warranty.......................................................3
Operational Warning...........................................................................................4
Introduction.........................................................................................................5
Important Safety Information......................................................................................................5
Safety Symbols and Signal Words.............................................................................................5
IMPORTANT Safety Information – MUST READ ......................................................................6
Overview ....................................................................................................................................8
Before You Get Started..............................................................................................................9
Specifications....................................................................................................12
Requirements...........................................................................................................................12
Output.......................................................................................................................................12
Dimensions ..............................................................................................................................13
Installation.........................................................................................................14
Arch Assembly.........................................................................................................................14
Utility Connections....................................................................................................................20
Nozzle Installation ....................................................................................................................22
Side Lens Installation...............................................................................................................23
Upper Lens Installation.............................................................................................................24
Initial Start Up...........................................................................................................................25

DURAJET™ ARCH
2 Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL028
Table of Contents
Maintenance ......................................................................................................27
Routine Procedures.................................................................................................................27
Trouble Shooting .....................................................................................................................27
Powder Coating Maintenance..................................................................................................28
Powder Coating Repair............................................................................................................29
Replacement Parts..................................................................................................................31

DURAJET™ ARCH
1MANUL028 Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Belanger Incorporated® Limited Warranty
LIMITED WARRANTY: Equipment: Seller warrants to the original purchaser that the goods sold hereunder, which are
fabricated by Seller, shall be free from defects in workmanship and material under normal use and service for a period of 1 year
plus 30 days from the date of invoice - CAT

Pumps will be warranted for 2 years from the date of invoice. All
warranties, express, implied, or statutory, pertaining to Seller’s machinery, parts, and equipment are fully set forth
herein. This limited warranty applies to the original purchaser only and is not transferable. No addition to or
modification of any of the provisions of this stated Limited Warranty shall be binding upon the Seller, unless made in
writing and signed by a duly authorized employee of Seller. This warranty is subject to the following limitations: (1)
This warranty shall be void if the factory specifications for operation and maintenance, found in original equipment
manuals, and component manuals, are not followed, or if other than factory authorized erection, alterations or
modifications are made to any parts or equipment; (2) Defective parts are warranted to the Purchaser for repair or
replacement through an authorized distributor of Seller or direct with Seller for a period of 13 months from the date
of invoice. Parts warranty excludes all claims for failure resulting from normal wear and tear to the depreciable parts,
improper installation, omission of factory specified preventative maintenance, misuse, abuse, negligence, third party
damages, or acts of God. Purchaser agrees to submit to and assist Seller or its authorized distributor in conducting
in-warranty inspections of the machinery and equipment including inspection of any part claimed to be defective by
the Purchaser; (3) Labor to repair or replace parts is warranted to Purchaser during normal business hours through
an authorized distributor of Seller or direct with Seller, for 120 days from date of invoice. Labor warranty excludes all
claims for failure resulting from normal wear and tear to the depreciable parts, improper installation, and omission of
factory specified preventative maintenance, misuse, abuse, negligence, third party damages, or acts of God. Seller
reserves the sole right to make determinations on the above stated limitation. All labor and service provided beyond
the labor warranty period shall be subject to labor charges at the rates established by the local authorized distributor
or direct with Seller; (4) This warranty shall be void for all equipment failures and premature component wear
caused by the use of corrosive chemicals in the wash process. The following list includes some, but not all, of the
particularly corrosive chemicals that if used in conjunction with Belanger® equipment will void the warranty:
Hydrofluoric Acid, Ammonium Bi-flouride, Bromic Acid, Muriatic Acid, Sulfonic Acid, Phosphoric Acid, Hydrogen
Cyanide, Hydrochloric Acid, Sodium Hydroxide and Chlorinated Solvents. (5) Seller makes no warranty, express or
implied, with respect to the design or operation of any entire system, in which Seller’s goods sold hereunder are
mere components. (6) In no event shall Seller be liable for any incidental, special, consequential or exemplary
damages resulting from the furnishing, performance or use of any goods or services sold pursuant hereto, whether
due to a breach of contract, breach of warranty, the negligence of Seller or to otherwise; not for loss of business;
inconvenience, or property damage of any kind; not for any damages of whatever nature resulting in any way from
the purchaser’s selection and use of any chemicals not manufactured exclusively by seller but used with the
purchased goods; or for any service not expressly provided herein related to or arising from the equipment or goods
sold. This limitation of liability extends to purchaser’s use of any engineering recommendations, sales
representations, technical assistance, advice or data supplied by seller to purchaser in connection with the goods or
services supplied, other than that information contained in Belanger® manuals.
Parts: Seller warrants to the original purchaser that the Replacement Parts sold hereunder, shall be free from
defects in workmanship and material under normal use and service for a period of 30 days from the date of invoice.
This limited warranty applies to the original purchaser only and is not transferable. (1) This warranty shall be void if
the factory specifications for operation and maintenance are not followed; (2) Parts warranty excludes all claims for
failure resulting from normal wear and tear to the depreciable parts, improper installation, omission of factory
specified preventative maintenance, misuse, abuse, negligence, third party damages, or acts of God. (3) This
warranty shall be void for all replacements parts failures and premature component wear caused by the use of
corrosive chemicals in the wash process. The following list includes some, but not all, of the particularly corrosive
chemicals that if used in conjunction with Belanger® replacement parts will void the warranty: Hydrofluoric Acid,
Ammonium Bi-flouride, Bromic Acid, Muriatic Acid, Sulfonic Acid, Phosphoric Acid, Hydrogen Cyanide, Hydrochloric
Acid, Sodium Hydroxide and Chlorinated Solvents.
THIS LIMITED WARRANTY FOR EQUIPMENT AND REPLACEMENT PARTS IS EXPRESSLY IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, WHETHER STATUTORY OR OTHERWISE,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
Copyright © 2000 by Belanger, Inc.® All rights reserved. No part of this work may be reproduced or transmitted in
any form or by any means, electronic or mechanical, including photocopying and recording, or by any information
storage or retrieval system, except as may be expressly permitted by the 1976 Copyright Act. Revised as of 8-15-
01. Belanger® reserves the right to change or modify the Belanger Inc.® Limited Warranty without notice.

DURAJET™ ARCH
4 Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL028
Operational Warning
Formulations containing the chemicals listed below are particularly dangerous and should not
be used even at low concentrations:
•Hydrofluoric Acid
•Ammonium Bi-fluoride
•Bromic Acid
•Muriatic Acid
•Sulfonic Acid
•Phosphoric Acid
•Hydrogen Cyanide
•Hydrochloric Acid
•Chlorinated Solvents
Belanger, Inc.®, does not endorse or condone the use of chemicals that are potentially dangerous to human health,
the environment or property. Belanger® recognizes that it is the right and sole decision of the end user operators of
our equipment as to the type and dilution ratio of the chemicals used in their facilities. We strongly recommend that
the end user does not select products containing any of the chemicals listed above as an ingredient in the wash
solutions. The chemicals listed above are potentially dangerous to human health, and have a detrimental,
deteriorating effect on the equipment and the facility. Be advised that a portion of, or all of your warranty will be
voided if you determine to use any of the chemicals listed above as an ingredient in the wash solutions in conjunction
with your Belanger® automatic car wash equipment:
Limitation (4), of Paragraph (8), Limited Warranty, of the Belanger® Terms and onditions of Sales describes the
potential limitation of warranty due to your chemical selection:
(4) This warranty shall be void for all equipment failures and premature component wear caused by the use of
corrosive chemicals in the wash process. The following list includes some, but not all, of the particularly corrosive
chemicals that if used in conjunction with Belanger® equipment will void the warranty: Hydrofluoric Acid,
Ammonium Bi-fluoride, Bromic Acid, Muriatic Acid, Sulfonic Acid, Phosphoric Acid, Hydrogen yanide,
Hydrochloric Acid, and hlorinated Solvents. The Purchaser also agrees to accept the responsibility and liability
for the selection and use of any chemicals listed above;
However, should the end user decide to use formulations containing any of the above ingredients, the end user should
institute a comprehensive training program and implement detailed operational parameters within their organization
for the proper handling and treatment of such products to minimize the potential dangers involved. onsult your
chemical supplier for assistance in establishing operational guidelines in the use of their products. MSDS (Material
Safety Data Sheet) should be obtained from the chemical supplier before using any chemical formulation.
CAUTION
During the installation process the installer is responsible for re-tightening ALL
lugs, set screws and terminals located in the electrical panels. Components may
vibrate loose during shipping.

DURAJET™ ARCH
1MANUL028 Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Introduction
Important Safety Information
This section introduces the hazard and safety precautions associated with installing, maintaining or servicing this product.
Before performing any task on this product, read this safety information and the applicable sections in this manual, where
additional hazards and safety precautions for your task may be found. Electrical shock could occur and cause death or
serious injury if these safe service procedures are not followed.
Safety Symbols and Signal Words
Alert Symbol
This safety alert symbol is used in this manual and on warning labels to alert you to
precautions which must be followed to prevent potential personal safety hazards. Obey
safety directives that follow this symbol to avoid possible injury or death.
Signal Words
The signal words used in this manual and on warning labels tell you the seriousness of particular safety hazards. The
precautions that follow must be followed to prevent death, injury or damage to the equipment.
DANGER
This signal word is used to alert you to a hazard or unsafe practice which WILL RESULT IN
DEATH OR SERIOUS INJURY
This alerts you to a hazard or unsafe practice which COULD RESULT IN DEATH OR
SERIOUS INJURY
CAUTION
This signal word designates a hazard or unsafe practice which MAY RESULT IN MINOR
INJURY
CAUTION
When used by itself, CAUTION designates a hazard or unsafe practice which MAY RESULT IN
PROPERTY OR EQUIPMENT DAMAGE
Before You Begin
Only trained or authorized individuals knowledgeable in the related procedures should install, inspect, maintain or
service this equipment.
Read the Manual
Read, understand and follow this manual and any other labels or related materials supplied with this equipment. If you
do not understand the procedure, call a Belanger, Inc.® representative at 248-349-7010. It is imperative to your safety
and the safety of others to understand the procedures before beginning work.

DURAJET™ ARCH
6 Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL028
Important Safety Information
IMPORTANT Safety Information – MUST READ
Safety Warnings
DISCONNECT THE MAIN POWER SUPPLY AND
DISSIPATE ALL POTENTIALLY HAZARDOUS
ENERGY SOURCES PRIOR TO SERVICING OR
MAINTAINING EQUIPMENT
Belanger® recommends that all workers observe the OSHA (U.S. Department of
Labor Occupational Safety & Health Administration) Lockout / Tagout procedure
to dissipate all potentially hazardous energy sources (i.e. - electrical, mechanical,
hydraulic, pneumatic, chemical, thermal, etc.) prior to performing service or
maintenance on machinery and equipment.
Note: Reference the OSHA standard for the Control of Hazardous Energy (Lockout/Tagout), Title 29
Code of Federal Regulations (CFR) Part 1910.147 and the example provided in 1910.147
Appendix A for practices and procedures necessary to disable machinery or equipment, thereby
preventing the release of hazardous energy while employees perform servicing and maintenance
activities. The standard outlines measures for controlling hazardous energies – electrical,
mechanical, hydraulic, pneumatic, chemical, thermal, and other energy sources.
Note: Reference the OSHA standard 29 CFR 1910.331 to 29 CFR 1910.335 for safe work practices to
protect employees working on electrical circuits and equipment. This section requires workers to
use safe work practices, including lockout and tagging procedures. These provisions apply when
employees are exposed to electrical hazards while working on, near, or with conductors or systems
that use electrical energy.
Note: Both referenced OSHA standards can be found at the following website: http://www.osha.gov/law-
regs.html. Browse to the General Industry tab under the Find an OSHA Standard heading, scroll
down to the link of interest and click on it.
Doing so will prevent unexpected energization, startup, or release of hazardous
energy while maintenance and servicing activities are being performed.

DURAJET™ ARCH
1MANUL028 Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Important Safety Information
Safety Warnings
BE SURE TO OBSERVE OPERATING ENVELOPE.
EQUIPMENT MAY START UNEXPECTEDLY. OVERHEAD,
ROTATING AND/OR MOVING COMPONENTS COULD
RESULT IN SERIOUS INJURY OR DEATH.
BE AWARE OF FOREIGN OBJECTS IN THE AREA
SURROUNDING A ROTATING PIECE OF EQUIPMENT.
OBJECTS MAY BECOME TANGLED WITH EQUIPMENT AND
COULD RESULT IN SERIOUS INJURY OR DEATH.
BE AWARE OF HAZARDS ASSOCIATED WITH
EQUIPMENT INSTALLED ON THE FLOOR
THAT MAY BE A TRIP HAZARD.
It is imperative to your safety and the safety of others to always follow safe work
procedures.

DURAJET™ ARCH
8 Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL028
Introduction
Overview
The DuraJet™ Arch was designed to provide a full application on the front, back and side
surfaces of the vehicle.
A 1/3 HP 3-phase motor mounted to the upper frame operates the patent pending sweeping
motion of the DuraJet™ Arch. A pitman arm attached to the motor gearbox assembly moves the
upper manifold channel side-to-side. The upper channel has roller bearings assembled to each
end that roll on guide plates. The guide plates attach the side manifold channel assemblies to the
upper channel assembly and have an engineered arc designed to create the swaying motion of
the top manifold. This design also synchronizes the up/down and inward/outward movement of
the side manifolds with the side-to-side swaying motion of the upper manifold.
The spray manifolds on the DuraJet™ are designed to rotate 30° toward the entrance and 30°
toward the exit of the bay. This feature provides a total rotation of 60° to provide a complete
application on the front, top, side and rear surfaces of the vehicle. Programmed outputs within
the system controller initiate operation. A 4-way pneumatic valve, located on the air panel,
operates a cylinder which rotates the manifolds. A motor starter panel initiates the motor gearbox
to trigger the sweeping motion. The DuraJet™ manifolds start at a 30° angle facing the tunnel
entrance and rotate to 30° toward the exit. The speed of this motion is user defined. In order to
maximize cleaning and rinsing on rear surfaces, Belanger® recommends setting the manifold
rotation toward the exit of the tunnel early enough that the water direction can also be
concentrated on the back of the vehicle mirrors.
The main water feed, 1-1/4” FNPT, is located on the exit side of the upper head assembly. This
feed splits into (2) 3/4” hydraulic hose assemblies that feed the upper manifold. A 3/4” hydraulic
hose assembly from each end of the upper manifold feeds each side manifolds. These 3/4”
hydraulic hose assemblies also help synchronize the upper and side manifold rotation when the
flipping cylinder activates. The upper and side manifolds are both constructed using 1” stainless
steel pipe with 1/4” NPT threaded flow drilled nozzle ports. Each side manifold has (6) nozzle
ports. The upper manifold has (7) nozzle ports. The (19) zero degree rotating nozzles contour the
vehicle surface and provide a full application. Based on the customer’s preference, the
DuraJet™ can be located in the tunnel to remove heavy dirt, remove triple foam or provide a final
rinse.
The DuraJet™ Arch has an extruded aluminum structure specifically engineered for Belanger®
equipment. An optional feature of the DuraJet™ is LED-illuminated spray manifolds. Bright white
LED lights, with a flashing option, back light the manifold covers. A 5 amp power supply
enclosure operates the LED lighting application.
The AlumaJet™ has the same engineered structure with an aluminum finish, black filler strips
and black plastic manifold covers. The AlumaJet™ does not include any other light or color
options.

DURAJET™ ARCH
1MANUL028 Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Introduction
Before You Get Started
Tools needed for installation:
hammer drill with 5/8” bit 25 foot extension cord
tape measure (25 foot or greater) tin snips
level safety glasses
miscellaneous hand tools work gloves
ladder 2 large pipe wrenches
(2) - lamps forklift
Equipment included:
Description Quantity
DuraJet™ or AlumaJet™ Arch Upright Leg Assemblies (typical) 2
DuraJet™ or AlumaJet™ Arch Head Assembly 1
DuraJet™ or AlumaJet™ Arch Side hannel Assemblies (typical) 2
DuraJet™ or AlumaJet™ Arch Accessory box: 110471 1
Accessory box contents: 110471
Part Number ty Description
1FSTNR-ST750 8 Kwick bolt 5/8” x 6”
1HOSE-HY020 2 orner Hose Assembly
1HOSE-HY033 2 Feed Hose Assembly
1FSTNR-HH522 8 1/2-13 x 1-1/2” HH S
1FSTNR-HH540 8 1/2-13 x 1-3/4” HH S
1WASHR-L 498 16 1/2” lock washer
110469 1 Air Panel
Note: Uncrate and inspect shipment for damage, and to verify that all pieces are there. If there is
any damaged equipment, file a claim with the trucking company immediately. Receiving
party is responsible for filing claim with trucking company. Notify your local distributor or
Belanger, Inc.® immediately if shipment is determined damaged or incomplete.

DURAJET™ ARCH
10 Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL028
Introduction
Available Nozzle Options
The nozzle pressure and water volume of the DuraJet™ or AlumaJet™ Arch depends on the
pump station capability, which allows the customization to accommodate the customer’s
vehicle washing strategies.
Nozzles are selected separately based on your pump station option. This ensures maximum
performance of your DuraJet™ or AlumaJet™ Arch.
KKit Part Number Descripion Nozzle Quantity
115006 Nozzle Kit for 36 GPM @ 600 psi DuraFlo™
Pumping Station
19
115005 Nozzle Kit for 36 GPM @ 1100 psi DuraFlo™
Pumping Station
19
Available Lens Cover Choices
The lens covers are available in a variety of colors for maximum market appeal.
UPPER Manifold over SIDE Manifold over olor
1PLST - V108 1PLST - V109 Natural
1PLST - V110 1PLST - V111 Black
1PLST - V112 1PLST - V113 Blue
1PLST - V114 1PLST - V115 Green
1PLST - V116 1PLST - V117 Orange
1PLST - V118 1PLST - V119 Red
1PLST - V120 1PLST - V121 Yellow
Additional components that are used with the Lens Covers:
Part Number Quanity Description
9460 4 orner Adapter
9488 2 orner Bellow
1FSTNR-HH198 2 5/16-18 X 1-1/4 HH S
1FSTNR-SB156 2 3/8-16 X 1-1/4 Stainless Steel Shoulder Bolt
1WASHR-FL415 2 5/16 Stainless Steel Flat Washer
1WASHR-L 270 2 5/16 Stainless Steel Lock Washer
1FSTNR-HK275 6 5/16-18 X 5/8 Black Hand Knob

DURAJET™ ARCH
1MANUL028 Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Introduction
Available DuraJet™ Filler Strip Options
DuraJet™ filler strips are available in a variety of colors for maximum market appeal. Replacement
filler strips are provided in 10 foot lengths and cut to size in the field.
Part Number olor
110479 Black
110480 Blue
110481 Green
110482 Gray
110483 Orange
110484 Red
110485 Yellow
Note: The AlumaJet™ is ONLY available with black filler strips (Replacement Part Number
110479).

DURAJET™ ARCH
12 Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL028
Specifications
Requirements
Physical
Tunnel space required 28-1/2”
Unit height 122”
Unit width 163”
Utility
Electrical 120VA (for ontroller, Air Panel, LED Package)
3-Phase (for 1/3 HP Electric Motor)
Pneumatic 1S FM @ 100 psi (for Flipping ylinder)
(2) 1/4” Polyflow Lines (between Air Panel and Flipping
ylinder ontrols on Machine)
Water 36 GPM @ 600 psi or 1100 psi (to feed nozzles)
Output
Physical
Vehicle clearance, height 88”
Vehicle clearance, width 145”
DISCONNECT AND LOCKOUT ELECTRICAL POWER AND DISSIPATE ALL
POTENTIALLY HAZARDOUS ENERGY SOURCES BEFORE SERVICING ANY
EQUIPMENT!
CAUTION
Always wear safety glasses when performing maintenance on any equipment
CAUTION
It is recommended that a licensed electrician is contracted to perform all electrical installations.
CAUTION
A compressed Air System should be set correctly to support 90 PSI necessary to operate
equipment, but should never be set to deliver more than 120 PSI air pressure to the Belanger®
specified equipment.

DURAJET™ ARCH
1MANUL028 Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Specifications
Dimensions
122”
163”
88”
learance with
Lens overs
145”
Clearance
28-1/2”

DURAJET™ ARCH
14 Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL028
Installation
Arch Assembly
1. Place the Head assembly in the bay so that the main feed manifold is on the exit side of the
machine. See the image below.
2. Lift the Head assembly. Using a fork lift and 2 C-clamps, clamp the Head assembly to each
fork. A typical clamping set up is shown below.
Direction
Of Travel
Head
Assembly
Main Feed
Manifold

DURAJET™ ARCH
1MANUL028 Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Installation
Arch Assembly
3. Bolt the (2) Upright Leg assemblies to the Head assembly using (8) 1/2-13 X 1-1/2 fasteners
and lock washers. See the image below.
Note: The Filler Strips on the Upright Leg assemblies should face the inside of the arch. See the
image above.
Direction
Of Travel
Head Assembly
Upright Leg (2)
1/2-13 X 1-
1/2
Fastener (8) 1/2" Lock
Washer (8)
Filler Strip (4)
(2) Per Upright Leg
Typical at Each Corner
Upright Leg (2)
Head Assembly

DURAJET™ ARCH
16 Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL028
Installation
Arch Assembly
4. Place the arch in the tunnel so that the outside of the driver side base plate is 54-1/2 inches
off the inside guide rail of the conveyor. See the image below.
5. Verify that the driver side Upright Leg is square to the inside guide rail of the conveyor and
secure the driver side of the arch to the floor using (4) 5/8 x 6” lag bolts. See the image below.
6. Verify that the Upright Legs are square and plumb to each other, then secure the passenger
side upright leg to the floor using (4) 5/8 x 6” lag bolts . See the image above.
Note: Make sure that the DuraJet™ Arch is level. Verify that there is an equal measurement
from the driver side to the passenger side at both the top and bottom of the arch.
Direction
Of Travel
54-1/2”
Inside Guide Rail
of the onveyor
Driver Side
Base Plate
Partial Top View of Wash Wall
Partial Top View of Wash Wall
Plumb-bob and
floor line
Verify that the distance between
the Upright Legs is the same at
the top and the bottom of the arch
Direction
Of Travel
Partial Top View
of onveyor
Top View of
DuraJet™ Arch
Head Assembly
Upright Leg (2)
5/8-16 X 6
Fastener (8)