Belanger QuickFire Wrap Around Signature Series User manual

QuickFire® Wrap Around Signature® Series
QuickFire® Wrap Around Signature Series
1MANUAL826 Rev03

Belanger Equipment Owner’s Manual
QuickFire® Wrap Around Signature® Series
Copyright 2022
Belanger, Inc®
This manual and the accompanying equipment are protected by United States trademark, copyright, and patent laws. You
may make one copy of this manual. Do not make additional copies of this manual or electronically transmit it in any form
whatsoever, in whole or in part, without the prior written permission of Belanger, Inc.®
The registered trademarks used in this document are the property of their respective owners. The use of such trademarks is
for reference purposes only and does not imply sponsorship or approval of Belanger, Inc.®by these companies or any
companies affiliated with their respective owners.

CURRENT REVISION LOG
1MANUL826 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Rev
Release
Date
Page
Description
03
03/18/22
3
Updated Limited Warranty
6
Added the two Warnings about Pneumatics (per Project #10055)
9
Under Utility added Hydraulic information
10
Added page, Installation: Identify Conveyor (per Project #32-523)
11
Removed dimension 153”
13
Added Note at top of the page for the 13” and14-1/2” Conveyor
Updated dimension to driver side QuickFire® Wrap 49-1/2” or 51” See Note Below
Added See Note Below to dimension 103-1/2”
Added to note under image: (13” Conveyor: 49-12” / 14-1/2” Conveyor: 51” and the 103-1/2”) (per
Project #32-523)
14 &15
Removed positioning dimensions from the pages for the QuickFire® Wraps
16
Added dimension to driver side QuickFire® Wrap 13” Conveyor: 49-1/2” and 14-1/2” Conveyor: 51”
In Step 2 after 49-1/2”, added: if the conveyor is 13” wide or 51” if the conveyor is 14-1/2” wide as
shown below. (per Project #32-523)
23
Added 1WASHR-FL498 to image
24-29
Replaced these pages with the information in the Mix and Match Manual - Securing the Head
Assembly to the Boom and Installing Drive Shaft Components for both Hydraulic & Electric
27
Corrected Knob part number from 8265 to 8259, 7094 to 8258, and added part number 1NUT-
JM500 to Jam Nut (per Change Request #87)
Added to Step 1: Parts 8259 and 8258 are part of the Head Assembly
32
Added Neo-Tex™fill information to the Lower Hub on the image (per Change Request #37)
Changed subtitle from Overview for Neo-Tex™Fill to Overview of Neo-Tex™Fill
34
Added more Neo-Tex™fill with Nylon Brush information to the image
Changed subtitle from Overview for Fleet Wash with Nylon Brush Packs to Overview of Neo-Tex™
Fill with Nylon Brush Packs for Fleet Wash (per Change Request #37)
36
Inserted page showing Overview of Neo-Tex™Fill for the Upper Hub (per Change Request #37)
41-54
Replaced these pages with the Utility Connections information in the Mix and Match Manual
46
In the note under Confirming Wheel Rotation changed the word below to above
63
Changed: During operation, the transition between portions of operation (i.e., front to side, side to
rear) will indicate by what is observed the adjustments needed for optimal QuickFire® Wrap
operation.
To: During a vehicle wash, observe the transitions between the different portions of the wash
operation (i.e., front to side, side to rear) this will indicate if adjustments are needed to optimize the
operation of the QuickFire® Wrap.
65
Under Routine Procedures, Daily removed Check the chemical injection pump(s)…and Hose down
the component and surrounding area at the end of each day. Added Check all hydraulic hose
connections for leaks and check for water, chemical, or air leaks…
Under Weekly removed: Check all tanks periodically for sludge… and added Hose down the
component and surrounding area…
Under Monthly removed Wash component down with a good degrimer… and grease bearings and
added Wash components frame and Check cleaning material for wear
Under Quarterly removed Scrub down aluminum portions…
66
Added Spherical Bearing Replacement Tip for Hydraulic Motor from Mix and Match Manual
67
Added Hydraulic Hose Replacement Procedure from the Mix and Match Manual
68
Add Electric after the Spherical Bearing Replacement Tip subheading
73
Added Powder Coating Maintenance information
74-75
Added Powder Coating Repair information
76
Changed Cylinder Mount Weldment part number from 8239 to 112304 (DS) /112305 (PS) (per
Project #10055)
78
Added reference part numbers 8258 & 8259 to the exploded view
Added note: Reference Parts 8258 & 8259 are part of the Electric & Hydraulic Head Assemblies
shown on the following pages (per Change Request #88)
Added Enlarged View at bottom and notes for 1NUT-RG942

CURRENT REVISION LOG
Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL826
Rev
Release
Date
Page
Description
79
Changed Gearbox Assembly number 1GEABX-AS986 to 112286 and 1GEABX-AS988 to 112288
(per ECN #5131)
82
Added Electric after the Boom Clamps Assembly subheading
84
Removed Signature Series from the QuickFire® Boom Utility Mount: Electric subheading and added
Electric
Added Electric Drive Boom Utility Mount part number 8234 (per Change Request #71)
85-90
Added Hydraulic Drive Exploded Views from the Mix and Match Manual
85
Changed part number 7065 to 9390
86
Changed part numbers: 7068 to 8266, 7083 to 9389, 7066 to 7990 (2 places), 7071 to 8263, 7069
to 8261 (2 places), 7095 to 8259, 7096 to 8264 (2 places), 7070 to 8262, 7094 to 8258, 7038 to
8260
88
Changed part numbers: 7085 to 8256, 7082 to 9388, and 7084 to 9391
90
Changed Boom Utility Mount Assembly numbers from DS: 108025 to 110426 and PS: 102855 to
110427
Changed part number 7102 to 9392
91
Changed part number 1VALVE-HY393 to 1VALVE-HY395 (per Change Request #10)
Corrected Air-Over-Oil Assembly # DS is 108892 & PS is 108891 they were reversed (per Change
Request #71 & Project #10055)
92
Removed spacer part number 8230 it is now part of Cylinder Mount Weldment DS:112304 and PS:
112305 (per Project #10055)
Added 1WASHR-FL498
96
Moved Neo-Tex™Wash Clips and Fill Pattern to a separate page (per Change Request #37)
97
Changed format of Neo-Tex™Only Fill Replacement charts (per Change Request #37)
Added Neo-Tex™complete fill replacement part number chart
Corrected 32”x10”x1/4”blue fill part number from 7685 to 6985 (per Change Request #106)
98
Changed format of Neo-Tex™with Nylon Brush Fill Replacement charts (per Change Request #37)
Added Neo-Tex™complete fill replacement part number chart
Corrected 32”x10”x1/4”blue fill part number from 7685 to 6985 (per Change Request #106)

QUICKFIRE® Signature ®Series
1MANUL826 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Table of Contents
Belanger Incorporated Limited Warranty........................................................ 3
Operational Warning......................................................................................... 4
Important Safety Information –MUST READ.................................................. 5
Safety Symbols and Signal Words............................................................................................................................... 5
Safety Warnings........................................................................................................................................................... 6
Introduction....................................................................................................... 7
Before You Get Started................................................................................................................................................ 8
Specifications.................................................................................................... 9
Requirements............................................................................................................................................................... 9
Output .......................................................................................................................................................................... 9
Installation....................................................................................................... 10
Identify Conveyor ....................................................................................................................................................... 10
Tunnel Placement Overview ...................................................................................................................................... 11
Positioning the Stands (Legs) .................................................................................................................................... 16
Installing the Booms................................................................................................................................................... 18
Installing Boom Components ..................................................................................................................................... 20
Securing the Head Assembly to the Boom: Hydraulic ............................................................................................... 24
Securing the Head Assembly to the Boom: Electric................................................................................................... 27
Installing Side Wheel Hubs ........................................................................................................................................ 30
Installing Cleaning Material........................................................................................................................................ 31
Adjusting the Positive Stops....................................................................................................................................... 40
Utility Connections ..................................................................................................................................................... 40
Utility Connections for Boom Movement .................................................................................................................... 41
Utility Connections for Side Wheels: Hydraulic.......................................................................................................... 44
Utility Connections for Side Wheels: Electric ............................................................................................................. 47
Initial Startup................................................................................................... 55
Wheel Speed.............................................................................................................................................................. 55
Air Settings................................................................................................................................................................. 55
Operational Performance and Controls ........................................................ 56
Understanding Air-Over-Oil........................................................................................................................................ 56
Understanding Regulator Adjustments ...................................................................................................................... 56
Understanding Component Movement ...................................................................................................................... 57
Overview of Controls.................................................................................................................................................. 58
Sizer Adjustment Steps.............................................................................................................................................. 60
Adjustment Affects / Options...................................................................................................................................... 61
Symptoms and Required Adjustments....................................................................................................................... 63

QUICKFIRE® Signature ®Series
2Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL826
Table of Contents
Maintenance.....................................................................................................64
Troubleshooting ..........................................................................................................................................................64
Routine Procedures ....................................................................................................................................................65
Daily ............................................................................................................................................................................................65
Weekly ........................................................................................................................................................................................65
Monthly........................................................................................................................................................................................65
General Replacement Information..............................................................................................................................66
Spherical Bearing Replacement Tip: Hydraulic ..........................................................................................................................66
Hydraulic Hose Replacement .....................................................................................................................................................67
Spherical Bearing Replacement Tip: Electric .............................................................................................................................68
Head Assembly Bearing Adjustment ..........................................................................................................................................68
Torque Plate and Electric Motor Replacement ...........................................................................................................69
Remove Motor Gearbox assembly .............................................................................................................................................69
Replacing Torque Plate Fasteners .............................................................................................................................................71
Reinstall Motor Gearbox assembly .............................................................................................................................................71
Powder Coating Maintenance.....................................................................................................................................73
Powder Coating Repair...............................................................................................................................................74
Replacement Parts .....................................................................................................................................................76
Stand Assembly ..........................................................................................................................................................................76
QuickFire® Filler Strips ...............................................................................................................................................................77
Boom Components .....................................................................................................................................................................78
Upper Head Assembly: Electric ..................................................................................................................................................79
Lower Head Assembly: Electric ..................................................................................................................................................81
Boom Clamps Assembly: Electric...............................................................................................................................................82
Boom Hose Manifold Assembly: Electric ....................................................................................................................................83
Boom Hoses: Electric..................................................................................................................................................................83
Boom Utility Mount: Electric ........................................................................................................................................................84
Boom Hoses: Electrical Enclosure Assembly .............................................................................................................................84
Head Assembly: Hydraulic..........................................................................................................................................................85
Boom Clamps Assembly: Hydraulic............................................................................................................................................87
Boom Hose Manifold Assembly: Hydraulic .................................................................................................................................88
Boom Hoses: Hydraulic ..............................................................................................................................................................89
Secondary Water Manifold: Hydraulic.........................................................................................................................................90
Posi-Stop.....................................................................................................................................................................................91
Air-Over-Oil Components............................................................................................................................................................91
Air-Over-Oil Cylinder and Mount.................................................................................................................................................92
108880: Driver Side Sizer Plate Assembly .................................................................................................................................93
108881: Passenger Side Sizer Plate Assembly .........................................................................................................................93
108878: Sizer / Actuator Pneumatic Assembly...........................................................................................................................94
108879: Adjustable Sizer Stop Assembly...................................................................................................................................94
Air Panel......................................................................................................................................................................................95
Neo-Tex™ Wash Clips................................................................................................................................................................96
Neo-Tex™Fill Pattern..................................................................................................................................................................96
Neo-Tex™ Only Fill Replacement ..............................................................................................................................................97
Neo-Tex™ with Nylon Brush Fill Replacement...........................................................................................................................98

QUICKFIRE® Signature ®Series
1MANUL826 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Belanger Incorporated Limited Warranty
LIMITED WARRANTY:
Equipment:
Subject to the limitations stated below, Seller warrants that the Equipment sold hereunder, which is fabricated by
Seller, shall be free from defects in workmanship and material under normal use and service for a period of 1 year plus
30 days from the date of invoice - CATPumps will be warranted for 2 years from the date of invoice.
Parts:
Subject to the limitations stated below, Seller warrants that the Parts sold hereunder, shall be free from defects in
workmanship and material under normal use and service for a period of 90 days from the date of invoice.
Limitations On All Warranties:
The warranties contained in this Section 13 are subject to the following limitations: (1) they are void if the factory
specifications for operation and maintenance, found in original equipment manuals, and component manuals, are not
followed, or if other than factory authorized erection, alterations or modifications are made to any Parts or Equipment;
(2) defective Parts are warranted to the Purchaser only for repair or replacement through an authorized Purchaser or
Distributor of Seller, or direct with Seller for a period of 13 months from the date of invoice; however, this warranty
excludes all claims for failure resulting from normal wear and tear, improper installation, omission of factory specified
preventative maintenance, misuse, abuse, negligence, third party damages, or acts of God and Purchaser agrees to
submit to and assist Seller or its authorized Purchaser or Distributor in conducting in-warranty inspections of the
Goods including inspection of any Equipment or Parts claimed to be defective by the Purchaser; (3) the cost of
providing labor or repair to replace Equipment and Parts warranted to Purchaser will be included within the warranty
only if such claim is made within 120 days from the date of invoice and then only during normal business hours
through an authorized Purchaser or Distributor of Seller, or direct with Seller, and labor and service provided beyond
the labor warranty period shall be subject to labor charges at the rates established by the local authorized Purchaser
or Distributor or direct with Seller; (4) the warranties shall be void for all Equipment failures and premature Part wear
caused by the use of corrosive chemicals in the wash process, and the following list includes some, but not all, of the
particularly corrosive chemicals that if used in conjunction with Equipment or Parts will void the warranty: Hydrofluoric
Acid, Ammonium Bi-fluoride, Bromic Acid, Muriatic Acid, Sulfonic Acid, Phosphoric Acid, Hydrogen Cyanide,
Hydrochloric Acid, Sodium Hydroxide and Chlorinated Solvents; (5) Seller makes no warranty, express or implied, with
respect to the design or operation of any entire system, in which Seller’s Equipment or Parts sold hereunder are mere
components;(6) in no event shall Seller be liable for any incidental, special, consequential, punitive or exemplary
damages resulting from the furnishing, performance or use of any Goods or services sold pursuant hereto, whether
due to a breach of contract, breach of warranty, negligence or any other claim at law or equity. Seller shall not be
liable for any damages of any kind, including, but not limited to, loss of business; inconvenience, or property damage
of any kind; nor for any damages of whatever nature resulting in any way from the Purchaser’s selection and use of
any chemicals not manufactured exclusively by Seller but used with the purchased Equipment or Parts; or for any
service not expressly provided herein related to or arising from the Equipment or Parts sold. Seller shall not be liable
for damages resulting from Purchaser’s use of any engineering recommendations, sales representations, technical
assistance, advice, or data other than that information contained in Belanger manuals; (7) all warranties, express,
implied, or statutory, pertaining to the Equipment and Parts apply to the Purchaser only; are not transferable; are fully
set forth herein; and no addition to or modification thereto shall be binding upon the Seller, unless made in writing and
signed by a duly authorized employee of Seller.
No Other Warranties:
THIS LIMITED WARRANTY FOR EQUIPMENT AND PARTS IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, WHETHER STATUTORY OR OTHERWISE, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE CONTAINED IN THE UNIFORM COMMERCIAL CODE –SALES ARE EXPRESSLY
DISCLAIMED.
Copyright ©2020 by Belanger, Inc. All rights reserved. No part of this work may be reproduced or transmitted in any
form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage
or retrieval system, except as may be expressly permitted by the 1976 Copyright Act. Belanger reserves the right to
change or modify the Belanger Inc. Limited warranty without notice.

QUICKFIRE® Signature ®Series
4Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL826
Operational Warning
Formulations containing the chemicals listed below are particularly dangerous and should not
be used even at low concentrations:
•Hydrofluoric Acid
•Ammonium Bi-fluoride
•Bromic Acid
•Muriatic Acid
•Sulfonic Acid
•Phosphoric Acid
•Hydrogen Cyanide
•Hydrochloric Acid
•Chlorinated Solvents
Belanger, Inc., does not endorse or condone the use of chemicals that are potentially
dangerous to human health, the environment, or property. Belanger recognizes that it is the
right and sole decision of the end-user operators of our equipment as to the type and dilution
ratio of the chemicals used in their facilities. We strongly recommend that the end-user does
not select products containing any of the chemicals listed above as an ingredient in the wash
solutions. The chemicals listed above are potentially dangerous to human health and have a
detrimental, deteriorating effect on the equipment and the facility. Be advised that a portion of,
or all of your warranty will be voided if you determine to use any of the chemicals listed above
as an ingredient in the wash solutions in conjunction with your Belanger automatic car wash
equipment:
Limitation (4), of Paragraph (8), Limited Warranty, of the Belanger Terms and Conditions of
Sales describes the potential limitation of warranty due to your chemical selection:
(4) This warranty shall be void for all equipment failures and premature component wear
caused by the use of corrosive chemicals in the wash process. The following list includes
some, but not all, of the particularly corrosive chemicals that if used in conjunction with
Belanger equipment will void the warranty: Hydrofluoric Acid, Ammonium Bi-fluoride, Bromic
Acid, Muriatic Acid, Sulfonic Acid, Phosphoric Acid, Hydrogen Cyanide, Hydrochloric Acid,
and Chlorinated Solvents. The Purchaser also agrees to accept the responsibility and
liability for selecting and using any chemicals listed above.
However, should the end-user decide to use formulations containing any of the above
ingredients, the end-user should institute a comprehensive training program and implement
detailed operational parameters within their organization for the proper handling and treatment
of such products to minimize the potential dangers involved. Consult your chemical supplier for
assistance in establishing operational guidelines in the use of their products. MSDS (Material
Safety Data Sheet) should be obtained from the chemical supplier before using any chemical
formulation.
During the installation process, the installer is responsible for re-tightening
ALL lugs, set screws, and terminals located in the electrical panels.
Components may vibrate loose during shipping.

QUICKFIRE® Signature ®Series
1MANUL826 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Important Safety Information –MUST READ
This section introduces the hazard and safety precautions associated with installing, maintaining, or
servicing this product. Before performing any task on this product, read this safety information and
the applicable sections in this manual, where additional hazards and safety precautions for your task
may be found. Electrical shock could occur and cause death or serious injury if these safe service
procedures are not followed.
Safety Symbols and Signal Words
Alert Symbol
This safety alert symbol is used in this manual and on warning labels to alert you to
precautions, which must be followed to prevent potential personal safety hazards.
Obey safety directives that follow this symbol to avoid possible injury or death.
Signal Words
The signal words used in this manual and on warning labels tell you the seriousness of
particular safety hazards. The precautions that follow must be followed to prevent death, injury,
or damage to the equipment.
This signal word is used to alert you to a hazard or unsafe practice which WILL RESULT IN
DEATH OR SERIOUS INJURY
This alerts you to a hazard or unsafe practice which COULD RESULT IN DEATH OR
SERIOUS INJURY
This signal word designates a hazard or unsafe practice, which MAY RESULT IN MINOR
INJURY
When used by itself, CAUTION designates a hazard or unsafe practice which MAY RESULT
IN PROPERTY OR EQUIPMENT DAMAGE
Before You Begin
Only trained or authorized individuals knowledgeable in the related procedures should install,
inspect, maintain or service this equipment.
Read the Manual
Read, understand and follow this manual and any other labels or related materials supplied with
this equipment. If you do not understand the procedure, call a Belanger, Inc. representative at
248-349-7010. It is imperative to your safety and the safety of others to understand the
procedures before beginning work.

QUICKFIRE® Signature ®Series
6Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL826
Important Safety Information –MUST READ
Safety Warnings
DISCONNECT MAIN POWER SUPPLY PRIOR TO SERVICING
OR MAINTAINING EQUIPMENT
Belanger recommends that all workers observe the OSHA (U.S. Department of
Labor Occupational Safety & Health Administration) Lockout / Tagout procedure
prior to performing service or maintenance on machinery and equipment. Doing so
will prevent unexpected energization, startup, or release of hazardous energy while
maintenance and servicing activities are being performed.
BE SURE TO OBSERVE THE OPERATING ENVELOPE. EQUIPMENT
MAY START UNEXPECTICALLY. OVERHEAD, ROTATING, AND/OR
MOVING COMPONENTS COULD RESULT IN SERIOUS INJURY OR
DEATH.
BE AWARE OF FOREIGN OBJECTS IN THE AREA SURROUNDING A
ROTATING PIECE OF EQUIPMENT. OBJECTS MAY BECOME
TANGLED WITH EQUIPMENT AND COULD RESULT IN SERIOUS
INJURY OR DEATH.
PNEUMATICS SHOULD RETRACT WHEEL(S) OUT OF THE PATH OF
THE VEHICLE IF MOTOR OVERLOAD IS TRIPPED.
PNEUMATIC OUTPUT FROM SYSTEM CONTROLLER TO PNEUMATIC
VALVE MUST HAVE ITS CIRCUIT INTERRUPTED IN THE EVENT OF
AN OVERLOAD TRIPPED. THIS USUALLY REQUIRES ROUTING THE
OUTPUT CIRCUIT TO THE PANEL HOUSING, THE MOTOR STARTER,
AND OVERLOAD. BELANGER CUSTOM PANELS ORDERED WITH
RETRACT CIRCUIT WILL HAVE NORMALLY OPEN CONTACT
TERMINALS INSTALLED WITH NOTATION ENDING IN RA AND RB.
BE AWARE OF HAZARDS ASSOCIATED WITH EQUIPMENT
INSTALLED ON THE FLOOR THAT MAY BE A TRIP HAZARD.
It is imperative to your safety and the safety of others to always follow safe
work procedures.

QUICKFIRE® Signature ®Series
1MANUL826 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Introduction
Congratulations on your purchase of the QuickFire® Wrap. During the design and concept stages,
engineering considered some of the maintenance and adjustment difficulties of our previous Wave
Wrap™. Noted changes addressed included: the difficulty of maintaining adjustments, replacement
of the head roller and bearing assembly is costly, deterioration of the cable on pulley system –which
is time-consuming when replacement is required. Therefore, the main focus when designing the
QuickFire® Wrap was to create a new (tall wheel) wrap around that can accommodate high-line
speeds, maximize the length of time on vehicle surface, and requires minimal maintenance.
Engineering feels confident that we have exceeded design expectations, as the QuickFire® Wrap
truly is a component in which FORM meets FUNCTION.
The QuickFire® Wrap is the first Belanger component utilizing a newly engineered oval aluminum
structure, providing a sleek signature appearance to the frame. The head assembly design is based
on the technology of the Gyro Head™, consisting of a unique socket joint that is maintenance-free.
Providing a full 360-degree fluid motion. The QuickFire® head glides down polished stainless steel
rails of the boom using engineered “maintenance free” Caterpillar bearings. The new linear
Caterpillar Bearings design eliminates costly maintenance issues accrued on the previous Wave
Wrap™.
The head is controlled in both directions of travel, using an exhaust flow control on the retract of the
cylinder. Controlling the speed of the head and maximizing time on the surface of a vehicle. The
pivot point of the QuickFire® Wrap has been adjusted to align with the side (sheet metal) of a
vehicle. Combined with the patent pending DynaTrigger the QuickFire® provides simultaneous pivot
and linear movement. The operation of the DynaTrigger mechanism accurately senses different
vehicle widths for maximum rear coverage and precise surface contact. To increase the benefits of
this feature we have taken a new approach in the manual, to define adjustments and thoroughly
explain how each adjustment affects operation performance.

QUICKFIRE® Signature ®Series
8Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL826
Introduction
Before You Get Started
Tools Needed for Installation:
Forklift
Clamps
Hammer drill with 5/8” (15.8 mm) bit
Tin snips
Tape measure (25 foot [8 meters] or greater)
Safety glasses
Miscellaneous hand tools
Work gloves
Level
50-foot extension cord
Equipment Included: Qty
QuickFire® Wrap stand assemblies
2
QuickFire® Wrap boom assemblies
2
QuickFire® Wrap head assemblies
2
QuickFire® Wrap air-over oil assemblies
2
QuickFire® Wrap sizer assemblies
2
QuickFire® Wrap boom utility mount assemblies
2
Accessory box
1
QuickFire® Wrap boom rails (96-1/2”)
4
QuickFire® Wrap shafts (102”)
2
Lower Hub assemblies (28-1/4” x 12” )
2
Upper Hub assemblies (42-1/4” x 6” )
2
Note: Uncrate and inspect the shipment for damage, and verify that all pieces are there. If there
is any damaged equipment, file a claim with the trucking company immediately. Receiving
party is responsible for filing a claim with the trucking company. Notify your local
distributor or Belanger, Inc. immediately If a shipment is determined damaged or
incomplete.

QUICKFIRE® Signature ®Series
1MANUL826 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Specifications
Requirements
Physical Working Envelope
Vehicle Clearance Height
90”
Vehicle Clearance Width
105”
Tunnel Space Required
222-1/2”
Unit Height
121”
Unit Width
153”
Utility
Electrical
Two Outputs from Controller @110VAC
Hydraulic
6 GPM @ 900 PSI
Pneumatic
1 CFM (clean, dry air) @ 90 PSI minimum 120 PSI maximum
Water
Two 3/4” Pipe @ 8 GPM @ 40 PSI
Output
Physical
Vehicle clearance, height
90”
Utility
Pneumatic
.3 CFM @ 90 PSI minimum 120 PSI maximum
DISCONNECT AND LOCKOUT ELECTRICAL POWER BEFORE SERVICING ANY
EQUIPMENT!
Always wear safety glasses when performing maintenance on any equipment
It is recommended that a licensed electrician is contracted to perform all electrical installations.
Note: YOUR HYDRAULIC SYSTEM MUST BE CAPABLE OF ADJUSTMENT TO 76 RPM
AT 900 PSI WHILE LOADED AGAINST VEHICLE. PLEASE VERIFY YOUR
SYSTEMS CAPABILITY TO MEET THESE SETTING WHILE RUNNING A
VEHICLE PRIOR TO INSTALLING PIECE OF EQUIPMENT!
A compressed Air System should be set correctly to support 90 PSI necessary to operate
equipment, but should never be set to deliver more than 120 PSI air pressure to the Belanger
specified equipment.

QUICKFIRE® Signature ®Series
10 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL826
Installation
Identify Conveyor
The QuickFire® Wrap assemblies can be installed in a tunnel with a Belanger® 13” or 14-1/2” wide
Conveyor that has either a single or double guide rail. Identifying the conveyor is crucial for properly
positioning the QuickFire® Wrap assemblies during installation. The Belanger® conveyor options
are shown in the images below.
Single Guide Rail Conveyor Assemblies (13” & 14-1/2” Wide)
Double Guide Rail Conveyor Assemblies (13” & 14-1/2” Wide)
13”
14-1/2”
13”
14-1/2”
Guide Rail

QUICKFIRE® Signature ®Series
1MANUL826 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Installation
Tunnel Placement Overview
The placement images shown in this document are all laid out with the
driver side Stand closer to the entrance of the tunnel. However, the most
important factor is that the two Stands are offset 78-1/2” as far as tunnel
depth. This means if your site is better suited with the passenger side Stand
closest to the tunnel entrance, be sure to adhere to the stated offset as
shown in the diagrams.
Side View
121"
Entrance View
204”
Operating Envelope
Direction of Travel
78-1/2"
190”
Minimum

QUICKFIRE® Signature ®Series
12 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL826
Installation
Tunnel Placement Overview
When placing a piece of equipment, tunnel depth will vary from site to site. Be sure to
allow an adequate operating envelope.
Adjust the Posi-Stops to decrease the rotation distance if your site has limited space, this is
covered later in the manual.
1) Locate the two stand assemblies (legs) and determine which is the driver side and the
passenger side. See the image above to assist in the determination.
There are three traditional installation configurations for the QuickFire® Wrap Around,
shown on the following pages.
•Standard, stand-alone
•Staggered with a set of Wave Low Side Washers™
•Staggered with a set of Wave Full Side Washers™
2) Use a forklift to position the QuickFire® Wrap Around ™ stand assemblies (legs) into their
appropriatetunnel location as shown on the following pages.
Be sure to clamp equipment securely to the forks of the forklift.
Do not stand under load while the forklift is in operation.
33°
12°
12°
33°
78-1/2"
Minimum

QUICKFIRE® Signature ®Series
1MANUL826 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]
Installation
Tunnel Placement Overview
Standard, Stand-Alone Configuration
Equipment around the Wrap should give ample room for the wheels to swing within the working
envelope.
Dimensions (13”Conveyor: 49-12” / 14-1/2”Conveyor: 51”and the 103-1/2”) are taken from
the outside of the base to the driver side edge of the inside guide rail as shown above.
The heavy dotted line shows the proper operating envelope.
Note: In this manual, a 13” wide Conveyor is shown in all images. If a 14-1/2” wide Conveyor is
installed at the site be sure to add 1-1/2" to the dimensions to position the driver side
QuickFire® Wrap assembly.
Note: Dimensions in this section are not intended for tunnel placement. Later in this manual,
it will give tunnel placement dimensions.
Note: Above image shown with booms and wash material installed to indicate operating
envelope required to function properly.
Direction of Travel
78-1/2"
Minimum
49-1/2" or 51”
See Note Below
103-1/2"
See Note
Below

QUICKFIRE® Signature ®Series
14 Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph [phone] * Fax [phone]MANUL826
Installation
Tunnel Placement Overview
Staggered with a set of Wave Low Side Washers™
Equipment around the Wrap should give ample room for the wheels to swing within the working
envelope.
150" minimum
78-1/2” minimum
Direction of Travel
78-1/2"
minimum
LSW
LSW
For more information and details on installation of the Low Side Washers, refer to the
Low Side Washer Manual 1MANUL860.
Important Installation Note:
Note: Above image shown with booms and wash material installed to indicate operating envelope
required to function properly.