Belden Telecast Fiber Systems THOR-SLG User manual

Telecast Fiber Systems
A Belden Brand
102 Grove Street
Worcester, MA 01605
www.telecast-fiber.com
Tel. [phone]
Fax [phone]
User Manual
Edition: 2011-10-31
THOR Large Switch
Model:
THOR-SLG
DISCONTINUED

THOR- Large Switch
2
2011-10-31
Copyright
© 2011. All rights reserved. This information may not be reproduced in any
manner without the prior written consent of the manufacturer.
Information in this document is subject to change without notice.
Trademarks
All trademark and trade names mentioned in this document are
acknowledged to be the property of their respective owners.
Disclaimer
While every precaution has been taken during preparation of this manual,
the manufacturer assumes no liability for errors or omissions. Neither does
the manufacturer assume any liability for damages resulting from the use
of the information contained herein.
The manufacturer reserves the right to change specifications, functions, or
circuitry of the product without notice.
The manufacturer cannot accept liability for damage due to misuse of the
product or due to any other circumstances outside the manufacturer’s
control (whether environmental or installation related). The manufacturer
shall not be liable for any loss, damage, or injury arising directly, indirectly,
incidentally, or consequently from the use of this product.

Contents
2011-10-31 3
Contents
1 About This Manual ....................................................................... 7
1.1 Scope.................................................................................. 7
1.2 Validity ................................................................................ 7
1.3 Cautions and Notes............................................................. 7
2 Safety Instructions ....................................................................... 8
3 Description ................................................................................... 9
3.1 Application .......................................................................... 9
3.2 System Overview .............................................................. 10
3.3 Product Range .................................................................. 11
3.4 Accessories....................................................................... 11
3.5 Device Views .................................................................... 13
3.5.1 Configuration Redundancy.................................. 13
3.5.2 Configuration Standard 1 .................................... 14
3.5.3 Configuration Standard 2 .................................... 15
3.6 Diagnostics and Status ..................................................... 16
3.6.1 Status LEDs ........................................................ 16
3.6.2 Status of Console Ports ...................................... 18
3.6.3 Status of the CPU ports ...................................... 21
3.6.4 Network Status.................................................... 24
3.6.5 Firmware Status.................................................. 26
3.7 Trace Function .................................................................. 28
3.8 Flash Memory Status ........................................................ 29
4 Installation .................................................................................. 31
4.1 Package Contents............................................................. 31
4.2 System Setup.................................................................... 32
4.3 Example Applications........................................................ 33
4.3.1 Single-Head KVM Switcher................................. 34
4.3.2 Dual-Head KVM Switcher ................................... 35
4.3.3 Quad-Head KVM Switcher .................................. 36
4.3.4 Single-Head KVM / USB 2.0 Switcher ................ 38

THOR- Large Switch
4
2011-10-31
4.3.5 Triple-Head KVM / USB 2.0 Switcher ................. 40
4.3.6 Training System 15 ............................................. 42
4.3.7 Training System 30 ............................................. 44
4.3.8 Crosspoint Switcher ............................................ 46
4.3.9 Parallel mode (Stacking)..................................... 48
4.3.10 Cascading ........................................................... 50
5 Configuration.............................................................................. 52
5.1 Command Mode................................................................ 52
5.2 Control of the THOR Large Switch.................................... 54
5.2.1 Control via OSD .................................................. 54
5.2.2 Control via Java Tool .......................................... 58
5.2.3 Control via LCD Display...................................... 64
5.2.4 Control via Serial Interface.................................. 68
5.3 System Settings ................................................................ 69
5.3.1 System................................................................ 69
5.3.2 Access ................................................................ 73
5.3.3 Switcher .............................................................. 76
5.3.4 Network............................................................... 81
5.3.5 Date and Time .................................................... 84
5.4 User Settings .................................................................... 86
5.4.1 User Properties ................................................... 86
5.4.2 User Switcher...................................................... 89
5.5 Console Settings............................................................... 91
5.5.1 Console Ports (CON Ports)................................. 91
5.5.2 Console Switcher (CON Switcher) ...................... 95
5.5.3 Mouse and Keyboard.......................................... 97
5.5.4 Touchscreen ..................................................... 100
5.5.5 Macro Keys ....................................................... 102
5.5.6 Follow Me (Multicast) ........................................ 105
5.6 CPU Settings .................................................................. 108
5.6.1 CPU Ports ......................................................... 108
5.7 Saving and Loading of configurations ............................. 111

Contents
2011-10-31 5
5.7.1 Saving of Configurations in the Switcher........... 111
5.7.2 Saving of Configurations in a File ..................... 111
5.7.3 Loading of Configurations ................................. 114
5.7.4 Saving and Loading of Configurations from FTP
.......................................................................... 117
6 Operation .................................................................................. 119
6.1 Operation by 'Hot Keys'................................................... 119
6.1.1 Direct Switchering ............................................. 119
6.1.2 Scan Mode........................................................ 120
6.1.3 Addressing of Master and Slave ....................... 120
6.1.4 Macro Keyboard................................................ 121
6.1.5 Function Keys F1 - F12..................................... 121
6.2 KVM Mode ...................................................................... 123
6.2.1 KVM List............................................................ 123
6.2.2 KVM Switcher Function..................................... 124
6.2.3 Follow Me Function (Multicast) ......................... 127
6.3 Crosspoint Mode ............................................................. 130
6.3.1 CON Ports in the Crosspoint Switcher .............. 130
6.3.2 CPU Ports in the Crosspoint Switcher .............. 133
6.4 Serial Interface................................................................ 135
6.5 Power On and Power Down Functions ........................... 136
6.5.1 Restart .............................................................. 136
6.5.2 Reset................................................................. 136
6.5.3 Power down ...................................................... 137
7 Specifications ........................................................................... 138
7.1 Interfaces ........................................................................ 138
7.1.1 RJ45 (Interconnect) .......................................... 138
7.1.2 Fiber SFP Type LC (Interconnect) .................... 138
7.1.3 RJ45 (Network) ................................................. 138
7.1.4 RS-232 (Serial) ................................................. 138
7.2 Interconnect Cable.......................................................... 139
7.2.1 Cat X................................................................. 139

THOR- Large Switch
6
2011-10-31
7.2.2 Fiber.................................................................. 140
7.3 Supported Peripherals .................................................... 141
7.3.1 KVM Extender................................................... 141
7.4 Serial Control .................................................................. 147
7.4.1 Command Structure.......................................... 147
7.4.2 Commands, Swiching Functions....................... 148
7.4.3 Assignment of Configuration File to Command
7.5 Connector Pinouts........................................................... 152
7.6 Power Supply.................................................................. 153
7.7 Environmental Conditions ............................................... 153
7.8 Size ................................................................................. 153
7.9 Shipping Weight.............................................................. 153
8 Troubleshooting....................................................................... 154
8.1 External Failure............................................................... 154
8.2 Failure at the Switcher .................................................... 154
8.3 Blank Screen................................................................... 155
8.4 Video Interference........................................................... 155
9 Technical Support .................................................................... 157
9.1 Support Checklist............................................................ 157
9.2 Shipping Checklist........................................................... 157
10 Regulatory and Standards Compliance ................................. 158
10.1 CE Declaration Of Conformity......................................... 158
10.2 North American Regulatory Compliance ......................... 159
10.3 WEEE ............................................................................. 159
10.4 RoHS .............................................................................. 159
11 Glossary.................................................................................... 160
12 Switcher specific Glossary...................................................... 163

THOR- Large Switch
2011-10-31 7
1 About This Manual
1.1 Scope
This manual describes how to install your THOR-SLG, operate it, and how
to perform troubleshooting.
1.2 Validity
This manual is valid for all devices listed on the front page. The product
code is printed on the base of the device.
1.3 Cautions and Notes
The following symbols are used in this manual:
This symbol indicates an important operating instruction that should be
followed to avoid any potential damage to hardware or property, loss of
data, or personal injury.
This symbol indicates important information to help you make the best use
of this product.
@ 5\mod_1278573321 245_6.doc @ 41528@ 1

THOR- Large Switch
8
2011-10-31
2 Safety Instructions
To ensure reliable and safe long-term operation of your THOR-SLG,
please note the following guidelines:
Installation
Only use the device according to this user manual. Otherwise, the
provided safety measures can be affected.
Only use in dry, indoor environments.
The THOR-SLG and the power supply units can get warm. Do not
situate them in an enclosed space without any airflow.
Do not place the power supply directly on top of the device.
Do not obscure ventilation holes.
Only use power supplies originally supplied with the product or
manufacturer-approved replacements. Do not use a power supply if it
appears to be defective or has a damaged case.
Connect all power supplies to grounded outlets. In each case, ensure
that the ground connection is maintained from the outlet socket
through to the power supply's AC power input.
Do not connect the link interface to any other equipment, particularly
network or telecommunications equipment.
Take any required ESD precautions.
Repair
Do not attempt to open or repair a power supply unit.
Do not attempt to open or repair the THOR-SLG. There are no user
serviceable parts inside.
Please contact your dealer or manufacturer if there is a fault.

THOR- Large Switch
2011-10-31 9
3 Description
3.1 Application
The THOR-SLG switcher is used to establish a connection from consoles
(monitor, keyboard, mouse, and other peripheral devices) to various
sources (computer, CPU).
In a maximum configuration, up to 16 independent consoles can be
switched with up to 32 independent sources.
The THOR-SLG switcher is only specified for use with extenders that are
able to transmit video, KVM and USB 2.0 signals.
The connection between the switcher and the KVM extenders can only be
made by Cat X or fiber cables.
The switcher serves as a repeater. Thus the switcher can be run a
maximum distance of 10 km away from the consoles and 10 km away
from the sources.

THOR- Large Switch
10
2011-10-31
3.2 System Overview
A THOR-SLG switcher system consists of a THOR-SLG switcher and one
or more CPU and CON units. The THOR-SLG switcher is connected to
the CPU and CON units by interconnect cables.
The CPU units are connected directly to the source (computer, CPU) by
the provided cables.
Monitor(s), keyboard and mouse are connected to the CON units.
The communication between the THOR-SLG switcher, the CPU, and
CON units takes place over the respective interconnect cables.
12 3 5
36
4
Example System Overview
1 Source (computer, CPU)
2 CPU Units
3 Interconnect cable
4 THOR-SLG switcher
5 CON Units
6 Console (monitor, keyboard, mouse)

THOR- Large Switch
2011-10-31 11
See Chapter 4.3, Page 33 for installation examples.
3.3 Product Range
Part No. Description
TH-SLG-8IN-OUT
THOR-SLG switcher for 8 users and 8 CPUs
TH-SLG-16IN-8OUT THOR-SLG switcher for 8 users and 16 CPUs
TH-SLG-24IN-8OUT THOR-SLG switcher for 8 users and 24 CPUs
TH-SLG-32IN-8OUT THOR-SLG switcher for 8 users and 32 CPUs
TH-SLG-8IN-16OUT THOR-SLG switcher for 16 users and 8 CPUs
TH-SLG-16IN-16OUT THOR-SLG switcher for 16 users and 16 CPUs
TH-SLG-24IN-16OUT THOR-SLG switcher for 16 users and 24 CPUs
TH-SLG-32IN-16OUT THOR-SLG switcher for 16 users and 32 CPUs
TH-SLG-EMPTY THOR-SLG switcher empty (consisting of a basic
chassis, a basic circuit board, a control board and a
plug-in power supply unit for free configuration)
3.4 Accessories
Part No. Description
TH-SLG-PS Plug-in power supply unit as a replacement or for
an upgrade to a redundant power supply
TH-SLG-OSD THOR-SLG OSD card
TH-SLG-DIS THOR-SLG display card
TH-SLG-M-CAT THOR-SLG Cat X I/O card
TH-SLG-M-MM THOR-SLG fiber I/O card, Multi-mode
TH-SLG-M-SM THOR-SLG fiber I/O card, Single-mode
TH-SLG-EMPTY-
MODULE THOR-SLG I/O card empty, for free configuration
SFP-MM Multi-mode SFP for the use in THOR-SLG
SFP-SM Single-mode GBIC for the use in THOR-SLG

THOR- Large Switch
12
2011-10-31
Part No. Description
1583A Belden Category 5e Cable for Non Plenum
1585A Belden Category 5e Cable for Plenum
2412 Belden Category 6 Cable for Non Plenum
2413 Belden Category 6 Cable for Plenum
You can find appropriate extenders or other components in chapter 7.3,
page 138.

THOR- Large Switch
2011-10-31 13
3.5 Device Views
The following views of the THOR-SLG switcher illustrate the different
available configurations, each completely equipped as an example.
3.5.1 Configuration Redundancy
Rear View
1 2 3 5 6 874
1 I/O module CPU (Cat X)
2 I/O module CPU (fiber)
3 I/O module console (Cat X)
4 I/O module console (fiber)
5 Connect to network (RJ45)
6 Connect to serial interface (D-sub 9-pole)
7 Connect to power supply unit 2 (redundancy)
8 Connect to power supply 1 (standard)
Front View
1 2 3
1 LCD display
2 Plug-in power supply unit 1 (standard)
3 Plug-in power supply unit 2 (redundancy)

THOR- Large Switch
14
2011-10-31
3.5.2 Configuration Standard 1
Rear View
1 2 3 5 6 74
1 I/O module CPU (Cat X)
2 I/O module CPU (fiber)
3 I/O module console (Cat X)
4 I/O module console (fiber)
5 Connect to network (RJ45)
6 Connect to serial interface (D-sub 9-pole)
7 Connect to power supply
Front View
1 2
1 LCD display
2 Plug-in power supply unit

THOR- Large Switch
2011-10-31 15
3.5.3 Configuration Standard 2
Rear View
1 2 3 6 7 84 5
1 I/O module CPU (Cat X)
2 I/O module CPU (fiber)
3 I/O module console (Cat X)
4 I/O module console (fiber)
5 LCD display
6 Connect to network (RJ45)
7 Connect to serial interface (D-sub 9-pole)
8 Connect to power supply
Front View
1
1 Plug-in power supply unit

THOR- Large Switch
16
2011-10-31
3.6 Diagnostics and Status
3.6.1 Status LEDs
The THOR-SLG is fitted with the following LEDs for overall status
indication on every I/O module:
I/O card Cat X
2 1
Rear View
1 Status LED left port
2 Status LED right port
Status LEDs on Cat X I/O modules
Pos. LED Status Description
Off Port offline
Flashing Port online, no connection via Cat X
cable
Link Status
(green)
On Connection via Cat X cable ok,
data traffic active.
Off Port offline
1,2
Link Status
(orange) Flashing
Port online, no connection via Cat X
cable.

THOR- Large Switch
2011-10-31 17
I/O card fiber
31 24
Rear View
1 Failure LED left port
2 Status LED left port
3 Status LED right port
4 Failure LED right port
Status LEDs on fiber I/O modules
Pos. LED Status Description
Off Port offline1,4 Failure
Status
(red) Flashing
Port online, SFP module failure signal
Off Port offline
On Port online, signal ok
2,3 Failure
Status
(green) Flashing
Port online, no signal

THOR- Large Switch
18
2011-10-31
3.6.2 Status of Console Ports
All of the connections between the various consoles and CPUs are shown
in this menu.
You have the following possibilities to access the status view of the
various console ports:
OSD
The general operation of the OSD is explained in chapter 5.2.1.
Select the menu item 'Status' in the main menu and then select 'CON
Ports'.
Switch to the 'CPU Port' view by pressing <F1>.
Menu View 'Status - CON Ports'

THOR- Large Switch
2011-10-31 19
You can find the following pictures in the status view:
Picture Description
Number of the console port
(black);
Name of the console port
(green)
Number of the CPU ports with
keyboard and mouse
connection ('K/M');
Number of the CPU ports with
video connection ('MON')
Java Tool
The general operation of the Java tool and the connection to the switcher
is explained in chapter 5.2.2 and in the Java tool itself.
Select the menu item 'Status' in the left menu bar and afterwards go to
'CON Ports'.
Menu View 'Status - CON Ports'

THOR- Large Switch
20
2011-10-31
LCD Display
The general operation of the LCD display is explained in chapter 5.2.3.
Select the menu item 'Status' in the main menu and then go to "Ports.”
The display consists of six pages.
The first four pages provide information of the existing video connections.
The last two pages provide information of the existing mouse and
keyboard connections.
Output Input
CPU_01 CON_01
CPU_02 n.c.
CPU_03 n.c.
CPU_04 n.c.
CPU_05 n.c.
CPU_06 n.c.
CPU_07 n.c.
CPU_08 n.c.
Status Ports
Draco major
Menu View 'Status – Ports' video connections
The following information is available in the status view of pages 1-4:
Field Description
Left column Name of CPU port
Right column Name of CON ports that is connected with the
output signal ('video') of the CPU port.
Output Input
CON_01 CPU_01
CON_02 n.c.
CON_03 n.c.
CON_04 n.c.
CON_05 n.c.
CON_06 n.c.
CON_07 n.c.
CON_08 n.c.
Status Ports
Draco major
Menu view 'Status – Ports' mouse/keyboard connection